HP D7171A - NetServer - LPr Bedienungsanleitung

HP NetServer LC 2000

Pedestal to Rack Guide

HP Part Number 5969-2110

Printed November 1999

Notice

The information contained in this document is subject to change without notice.

Hewlett-Packard makes no warranty of any kind with regard to this

material, including, but not limited to, the implied warranties of

merchantability and fitness for a particular purpose. Hewlett-Packard shall not

be liable for errors contained herein or for incidental or consequential damages in

connection with the furnishing, performance, or use of this material.

Hewlett-Packard assumes no responsibility for the use or reliability of its software

on equipment that is not furnished by Hewlett-Packard.

This document contains proprietary information that is protected by copyright.

All rights are reserved. No part of this document may be photocopied, reproduced,

or translated to another language without the prior written consent of

Hewlett-Packard Company.

Windows NT®, Windows 95®, and Windows 98®are registered trademarks of

Microsoft in the U.S. and other countries.

3M®is a registered trademark of Minnesota Mining and Manufacturing Company.

Torx®is a registered trademark of CamCar/Textron, Inc.

Tinnerman®is a registered trademark of Eaton/Tinnerman.

Hewlett-Packard Company

Network Server Division

Technical Communications MS 45SLE

10955 Tantau Avenue

Cupertino, California 95014 USA

Audience Assumptions

The guide is for the person who installs, administers, and troubleshoots LAN

servers. Hewlett-Packard Company assumes you are qualified in the servicing of

computer equipment and trained in recognizing hazards in products with

hazardous energy levels and are familiar with weight and stability precautions for

rack installations.

iii

Contents

1 Preparing the HP NetServer for Rack-Mounting ........................................ 1

Introduction ................................................................................................... 1

Tools Required.......................................................................................... 1

Removing the HP NetServer’s Top Cover and Pedestal................................. 2

Removing the Bezel .................................................................................. 3

Removing the Top Cover........................................................................... 4

Removing the Pedestal.............................................................................. 5

2 Rack Mounting the HP NetServer ............................................................... 7

Introduction ................................................................................................... 7

Tools Required.......................................................................................... 8

Safety Precautions.................................................................................... 9

Preparing the Rack...................................................................................... 10

HP NetServer Rack Mount Parts List....................................................... 10

Marking the Rack and Attaching Rack Nuts ............................................. 10

Attaching the Column Adapters and Slides.............................................. 13

Attach the Hinge Assembly and Catch Assembly..................................... 16

Attach the Mounting Handles................................................................... 17

Placing the HP NetServer in the Rack...................................................... 18

Attaching the Cable Management Arm..................................................... 22

Attaching the Front Bezel ........................................................................ 24

Continuing with the Rack Installation Process.............................................. 25

Index............................................................................................................... 27

1 Preparing the HP NetServer for

Rack-Mounting

Introduction

This chapter describes how to remove the top cover and the pedestal from the

HP NetServer LC.

WARNING Before removing the top cover, shut down the operating

system and disconnect the power cords and unplug telephone

cables. Disconnect the power cords to avoid exposure to

high energy levels that may cause burns when parts are

short-circuited by metal objects, such as tools or jewelry.

Disconnect telephone cables to avoid exposure to a shock

hazard from telephone ringing voltages.

Tools Required

An anti-static service kit (3M 8501/8502/8503 or equivalent). This kit

includes a static-dissipating work surface, a chassis clip lead, and a wrist

strap.

Chapter 1 Preparing the HP NetServer for Rack-Mounting

Removing the HP NetServer’s Top Cover and

Pedestal

Use this procedure to remove the bezel, top cover, and pedestal from the pedestal

version of the HP NetServer LC 2000.

WARNING Do not operate the HP NetServer with its covers removed.

Always disconnect the power cord before removing any

covers, to avoid exposure to high energy levels that may cause

burns when parts are short-circuited bymetal objects such as

tools or jewelry. Disconnect any telephone cables to avoid

exposure to shock hazard from telephone ringing voltages.

CAUTION To prevent overheating, never operate the NetServer with its

cover removed. This includes the power supplies and Hot

Swap hard disks, which must be replaced or the opening

covered immediately (within 2 minutes).

1. If the HP NetServer is operating, log off all users and if necessary back-up

files.

2. Follow instructions in your network operating system (NOS)

documentation to gracefully shut down all networking software and

applications.

3. Press the power switch on the HP NetServer’s control panel when

prompted by the operating system.

Normally, this completes the power down procedure.

4. Disconnect the power cord from its power source.

Chapter 1 Preparing the HP NetServer for Rack-Mounting

Removing the Bezel

1. Pull the top of the bezel forward until it unsnaps.

2. Lift the entire bezel upward and away from the chassis. See Figure 1-1.

The bezel connects to the front of the HP NetServer chassis with two snap-in

connectors at the top front of the chassis and two metal tabs, which fit into

two slots on the bottom front of the chassis.

Figure 1-1. Removing the HP NetServer LC 2000 Bezel

CAUTION To prevent damage to the covers, support the cover as you

remove it from the HP NetServer. The NetServer’s covers can

be easily damaged.

Chapter 1 Preparing the HP NetServer for Rack-Mounting

Removing the Top Cover

1. Remove the single screw that secures the top cover to the front of the

NetServer.

2. Slide the top cover forward to disengage the mounting brackets.

3. Lift the top cover off (See Figure 1-2).

Screw Hole

Top Cover

Figure 1-2. Removing the Top Cover

Chapter 1 Preparing the HP NetServer for Rack-Mounting

Removing the Pedestal

The pedestal version of the HP NetServer LC 2000 mounts to an anti-tip pedestal,

which can be easily removed, if necessary.

NOTE The front bezel is shown removed, but the bezel may remain on

the chassis while removing the pedestal.

1. Disconnect all cables connected to the rear of the NetServer that would

limit its rotation before continuing.

2. Turn the NetServer over onto its top and pull up on the two tabs as shown

in Figure 1-3.

Figure 1-3. Removing the Pedestal

3. Slide the pedestal to the rear of the NetServer as shown in Figure 1-3.

Andere Handbücher für D7171A - NetServer - LPr

117

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere HP Server Handbücher

HP ProLiant DL180 Gen9 Bedienungsanleitung

HP t410 Bedienungsanleitung

HP Integrity rx4610 Bedienungsanleitung

HP 3000/9x9KS Series Bedienungsanleitung

HP ProLiant DL160 G6 Montageanleitung

HP ProLiant DL585 Gebrauchsanweisung

HP ProLiant DL585 Handbuch

HP ProLiant DL580 Generation 2 Handbuch

HP DL385 - ProLiant - G5 Bedienungsanleitung

HP D5970A - NetServer - LCII Bedienungsanleitung

HP BladeSystem bc2000 - Blade PC Bedienungs- und Sicherheitshinweise

HP Compaq t1010 Bedienungsanleitung

HP T5125 - Compaq Thin Client Betriebsanleitung

HP ProLiant DL140 Gebrauchsanweisung

HP Enterprise ProLiant DL380 Gen10 Handbuch

HP T5700 - compaq thin client Referenzhandbuch

HP t5745 - Thin Client Gebrauchsanweisung

HP T5730w - Compaq Thin Client Gebrauchsanweisung

HP rp8420 Installationsanleitung

HP D7171A - NetServer - LPr Stücklistenhandbuch

HP t5740e - Thin Client Bedienungsanleitung

HP ProLiant DL360p Bedienungsanleitung

HP ProLiant XL730f Gen9 Server Betriebsanleitung

HP Rx2620-2 - Integrity - 0 MB RAM Bedienungsanleitung

Beliebte Server Handbücher anderer Marken

Dell

Dell PowerEdge R410 Bedienungsanleitung

PowerNAS

PowerNAS CMA Bedienungsanleitung

Supero

Supero FatTwin F617R3-FT Bedienungsanleitung

MSI

MSI P1-109N-L70 Bedienungsanleitung

Dell

Dell PowerEdge XE9640 Handbuch

Dell

Dell PS4100 Montageanleitung

EtroVISION

EtroVISION EV3151 Bedienungsanleitung

NEC

NEC Express5800/T110j Bedienungsanleitung

Compaq

Compaq ProLiant 3000 Handbuch

Dell

Dell PowerEdge 3YPMN Bedienungsanleitung

iRobo

iRobo IPC2U Bedienungsanleitung

Nortel

Nortel 1000 Con?guration guide Bedienungsanleitung

Asus

Asus AP7500 Bedienungs- und Wartungshandbuch

Avid Technology

Avid Technology AirSpeed 5000 Bedienungsanleitung

Milestone

Milestone Husky IVO 350T Bedienungsanleitung

Planet

Planet NAS-7410 Bedienungsanleitung

Lenovo

Lenovo ThinkSystem SR635 V3 Bedienungsanleitung

Dell

Dell PowerEdge HS5610 Handbuch