HP ProLiant BL495c - G5 Server Bedienungsanleitung
HP ProLiant BL495c Server
Blade
Installation Instructions
Overview
Installation of a server blade requires the following steps:
1. Install and configure an HP BladeSystem c-Class enclosure.
2. Install any server blade options.
3. Install interconnect modules in the enclosure.
4. Connect the interconnect modules to the network.
5. Install a server blade.
6. Complete the server blade configuration.
For definitions of the acronyms used in this document, refer to
"Acronyms and abbreviations" in the server blade user guide.
Installing an HP BladeSystem c-
Class enclosure
Before performing any server blade-specific procedures, install an
HP BladeSystem c-Class enclosure.
The most current documentation for server blades and other
HP BladeSystem components is available at the HP website
(http://www.hp.com/go/bladesystem/documentation).
Documentation is also available in the following locations:
•Documentation CD that ships with the enclosure
•HP Business Support Center website
(http://www.hp.com/support)
•HP Technical Documentation website (http://docs.hp.com)
Installing server blade options
Before installing and initializing the server blade, install any server
blade options, such as an additional processor, hard drive, or
mezzanine card. For server blade options installation information,
see the HP ProLiant BL495c Server Blade User Guide on the HP
website (http://www.hp.com/go/bladesystem/documentation).
Installing interconnect modules
For specific steps to install interconnect modules, see the
documentation that ships with the interconnect module.
© Copyright 2008, 2009 Hewlett-Packard Development Company, L.P.
The information contained herein is subject to change without notice. The
only warranties for HP products and services are set forth in the express
warranty statements accompanying such products and services. Nothing
herein should be construed as constituting an additional warranty. HP shall
not be liable for technical or editorial errors or omissions contained herein.
Part Number 466196-003
April 2009 (Third Edition)
Interconnect bay numbering and device
mapping
•HP BladeSystem c7000 Enclosure
To support network connections for specific signals, install an
interconnect module in the bay corresponding to the embedded
NIC or mezzanine signals.
Server blade
signal
Interconnect bay Interconnect bay labels
Flex-10 NIC 1
(embedded) 1
Flex-10 NIC 2
(embedded) 2
Mezzanine 1 3 and 4
Mezzanine 2 5 and 6
7 and 8
For detailed port mapping information, see the HP BladeSystem
enclosure installation poster or the HP BladeSystem enclosure setup
and installation guide on the HP website
(http://www.hp.com/go/bladesystem/documentation).
•HP BladeSystem c3000 Enclosure and Tower Enclosure
Server blade
signal Interconnect
bay number Interconnect
bay label Notes
Flex-10 NIC 1,
2 (embedded)
1 —
Mezzanine 1 2 Four port cards
connect to bay 2
Mezzanine 2 3,4 •Four port cards
•Ports 1 and 3
connect to bay 3
•Ports 2 and 4
connect to bay 4
For detailed port mapping information, see the HP BladeSystem
enclosure installation poster or the HP BladeSystem enclosure setup
and installation guide on the HP website
(http://www.hp.com/go/bladesystem/documentation).
Connecting to the network
To connect the HP BladeSystem to a network, each enclosure must
be configured with network interconnect devices to manage
signals between the server blades and the external network.
Two types of interconnect modules are available for HP
BladeSystem c-Class enclosures: Pass-thru modules and switch
modules. For more information about interconnect module options,
see the HP website
(http://www.hp.com/go/bladesystem/interconnects).
Installing a server blade
CAUTION: To prevent improper cooling and thermal
damage, do not operate the server blade enclosure unless
all bays are populated with either a component or a
blank.
1. Remove the device bay blank.
2. Remove the enclosure connector cover.
3. Prepare the server blade for installation.
4. Install the server blade.
Completing the configuration
To complete the server blade and HP BladeSystem configuration,
see the overview card that ships with the enclosure.
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
Andere HP Server Handbücher
HP
HP Tc4100 - Server - 256 MB RAM Betriebsanleitung
HP
HP Color LaserJet Enterprise CP5525 Kurzanleitung
HP
HP ProLiant Lights-Out 100i Gebrauchsanweisung
HP
HP Integrity BL890c - i2 Server Gebrauchs- und Wartungshandbuch
HP
HP LaserJet 9000 Bedienungsanleitung
HP
HP Integrity rx2800 - i2 Gebrauchsanweisung
HP
HP A4500A - VMEbus Single Board Computer 744... Bedienungsanleitung
HP
HP Disk Carrier Blade for bh3710 Bedienungsanleitung
HP
HP P2000 G3 Bedienungsanleitung
HP
HP DL320 - ProLiant - G3 Gebrauchsanweisung
HP
HP ProLiant DL380 Gen9 Bedienungsanleitung
HP
HP 3020 Bedienungsanleitung
HP
HP Integrity rx1600 Bedienungsanleitung
HP
HP HP DL360 G7 Montageanleitung
HP
HP T5135 - Compaq Thin Client Referenzhandbuch
HP
HP P5389A - Intel Pentium III-S 1.4 GHz Processor... Bedienungsanleitung
HP
HP BL480c - ProLiant - 4 GB RAM Bedienungsanleitung
HP
HP StorageWorks P4000 Series Anleitung zur Verwendung
HP
HP ProLiant DL180 G6 Montageanleitung
HP
HP AlphaServer ES47 Service-Handbuch
