HP NetServer e 800 Bedienungsanleitung

HP Part Number D9394-90000

Printed June 2000

HP NetServer E 800

Installation Guide

Notice

The information contained in this document is subject to change without notice.

Hewlett-Packard makes no warranty of any kind with regard to this

material, including, but not limited to, the implied warranties of

merchantability and fitness for a particular purpose. Hewlett-Packard shall

not be liable for errors contained herein or for incidental or consequential

damages in connection with the furnishing, performance, or use of this material.

Hewlett-Packard assumes no responsibility for the use or reliability of its software

on equipment that is not furnished by Hewlett-Packard.

This document contains proprietary information that is protected by copyright.

All rights are reserved. No part of this document may be photocopied,

reproduced, or translated to another language without the prior written consent of

Hewlett-Packard Company.

Intel®and Pentium®are registered trademarks of Intel Corporation. Microsoft®,

Windows NT®, Windows 95®and Windows 2000®are registered trademarks of

Microsoft in the U.S. and other countries. Novell®and NetWare®are registered

trademarks of Novell, Incorporated in the U.S. and other countries. Symantec®is a

registered trademark of Symantec, Incorporated. pcANYWHERE32™ is a trademark

of Symantec, Incorporated. Torx®is a registered trademark of CamCar/Textron,

Incorporated.

Hewlett-Packard Company

Network Server Division

Technical Communications / MS 45SLE

10955 Tantau Avenue

Cupertino, California 95014 USA

Audience Assumptions

This guide is for the person who installs, administers, and troubleshoots LAN

servers. Hewlett-Packard Company assumes you are qualified in the servicing of

computer equipment and trained in recognizing hazards in products with

hazardous energy levels.

iii

Contents

Setting Up the HP NetServer E 800................................................................. 1

Introduction ................................................................................................... 1

Step 1: Attaching all the Cables................................................................. 2

Step 2: Opening the HP NetServer............................................................ 3

Step 3: Installing Memory.......................................................................... 5

Step 4: Installing Mass Storage Devices.................................................... 6

Step 5: Installing Adapter Boards............................................................. 10

Step 6: Installing a Second Processor ..................................................... 14

Step 7: Configuring the HP NetServer..................................................... 19

Setting Up the HP NetServer E 800

Introduction

This installation guide is a quick reference for HP NetServer E 800 installation.

Skip any steps that do not apply to your installation. Refer to the figures below

for connection and operating information. For more information, refer to the

HP NetServer E 800 User Guide.

Flexible

Disk Drive

CD-ROM Drive

Power ON/OFF/

Sleep Switch

Power ON/

OFF/Sleep LED

SCSI Drive

Activity LED

Optional Back-Up

Tape Drive

Power

Mouse

Keyboard

USB(2) LAN

Serial A

Parallel

Serial B

Video

(SVGA)

Key Lock

External SCSI

(Optional)

Fold-Out

Feet (4)

Unlocked Position

Locked Position

Setting Up the HP NetServer E 800

Step 1: Attaching all the Cables

If you are not installing any accessories, attach all available cables to the

respective connectors, then go to "Step 7: Configuring the HP NetServer."

NOTE The two USB connectors are reserved for printers, scanners,

and external modems. The NetServer does not support USB

connections for the keyboard and mouse.

Power

Power Cord

Strain Relief

Mouse

Keyboard

Video

SVGA

LAN

Setting Up the HP NetServer E 800

Step 2: Opening the HP NetServer

Tools Required:

•¼ inch flat-blade screwdriver

•Torx T-15 driver

WARNING Before removing the cover, always disconnect the power cord

and remove the telephone cable.

Disconnect the power cord to avoid exposure to high energy

levels that may cause burns when parts are short-circuited by

metal objects such as tools or jewelry. Disconnect telephone

cables to avoid exposure to shock hazard from telephone

ringing voltages.

Key-

Lock

Slotted

Thumbscrews(6)

Setting Up the HP NetServer E 800

Front of Chassis

Bottom of Chassis

Cover

Latch Opening

Air Duct

Latch

Setting Up the HP NetServer E 800

Step 3: Installing Memory

•Use only HP DIMMs, which are 3.3V, 168-pin, PC133 (133 MHz),

buffered SDRAM DIMMs in 128 MB, 256 MB, or 512 MB.

•DIMMs may be installed in any slot, in any combination (sizes mixed), in

any order, but HP recommends starting at slot 0 and filling the slots in

order with the largest size first: 0, 1, 2, and 3.

•Ensure both latches close on the DIMM when completely installed.

System Board

0123

Retaining Latches

DIMM Slot

Keys

Notches

Setting Up the HP NetServer E 800

Step 4: Installing Mass Storage Devices

•The NetServer is internally limited to 7 mass storage shelves.

The flexible disk drive and CD-ROM drive, which are standard on all

models of the HP NetServer E 800, occupy shelves 1 and 2 respectively.

•If a backup tape drive is used, it will occupy shelf 3.

•Shelves 4, 5, 6, and 7 are available for up to four SCSI hard drives and at

least one is required for the boot drive.

•IDE drives are not supported in this NetServer.

CAUTION Do not connect high voltage differential (HVD) SCSI devices

on the SCSI bus or you will damage the other devices.

1. Remove the Drive Cage by loosening the three captive screws.

Top of Chassis (Side view)

Captive Screws (3)

Front of

HP NetServer

Hard Disk

Drive Cage

(removable)

Shelf 1

Shelf 2

Shelf 3

Shelves 4-7 (4)

2. Install the SCSI hard disk drive.

Andere Handbücher für NetServer e 800

Inhaltsverzeichnis

Andere HP Server Handbücher

HP BL465c - ProLiant - 2 GB RAM Bedienungsanleitung

HP BL870c i2 Integrity Bedienungsanleitung

HP ProLiant DL560 Gen11 Bedienungsanleitung

HP t5335 - Thin Client Bedienungsanleitung

HP D7171A - NetServer - LPr Bedienungsanleitung

HP cc2300 Bedienungsanleitung

HP Integrity BL890c - i2 Server Bedienungsanleitung

HP Blade bc1000 Handbuch

HP NetServer AA 4000 Bedienungsanleitung

HP T5125 - Compaq Thin Client Service-Handbuch

HP BL20p - ProLiant - G2 Bedienungs- und Sicherheitshinweise

HP ProLiant ML310 Generation 5p Gebrauchsanweisung

HP ProLiant DL320e Gen8 v2 Bedienungsanleitung

HP ProLiant BL460c Gen9 Bedienungsanleitung

HP Cluster Platform Hardware Kits v2010 Bedienungsanleitung

HP LC2000r - NetServer - 128 MB RAM Bedienungsanleitung

HP D7171A - NetServer - LPr Bedienungsanleitung

HP Apollo 4200 Gen9 Handbuch

HP A9834-9001B Bedienungsanleitung

HP L1000 - 9000 - 0 MB RAM Betriebsanleitung

HP t5300 - Thin Client Bedienungsanleitung

HP ProLiant DL360p Gen8 Handbuch

HP Tc2120 - Server - 256 MB RAM Bedienungsanleitung

HP ProLiant DL185 Generation 5 Handbuch

Beliebte Server Handbücher anderer Marken

Dell

Dell PowerEdge R410 Bedienungsanleitung

PowerNAS

PowerNAS CMA Bedienungsanleitung

Supero

Supero FatTwin F617R3-FT Bedienungsanleitung

MSI

MSI P1-109N-L70 Bedienungsanleitung

Dell

Dell PowerEdge XE9640 Handbuch

Dell

Dell PS4100 Montageanleitung

EtroVISION

EtroVISION EV3151 Bedienungsanleitung

NEC

NEC Express5800/T110j Bedienungsanleitung

Compaq

Compaq ProLiant 3000 Handbuch

Dell

Dell PowerEdge 3YPMN Bedienungsanleitung

iRobo

iRobo IPC2U Bedienungsanleitung

Nortel

Nortel 1000 Con?guration guide Bedienungsanleitung

Asus

Asus AP7500 Bedienungs- und Wartungshandbuch

Avid Technology

Avid Technology AirSpeed 5000 Bedienungsanleitung

Milestone

Milestone Husky IVO 350T Bedienungsanleitung

Planet

Planet NAS-7410 Bedienungsanleitung

Lenovo

Lenovo ThinkSystem SR635 V3 Bedienungsanleitung

Dell

Dell PowerEdge HS5610 Handbuch