HP 1040 Programmierhandbuch

HP MSA 1040 Quick Start

Instructions

Abstract

These instructions provide an overview of planning,

installation, and configuration steps.

*759126-001*

HP Part Number: 759126-001

Published: March 2014

Edition: 1

This document is for the person who installs,

administers, and troubleshoots servers and storage

systems. HP assumes that you are qualified in servicing

and installing computer equipment, and are trained

in recognizing hazards in products and hazardous

energy levels.

Feature overview

The HP MSA 1040 is available in six models:

•FC Dual Controller LFF Storage

•FC Dual Controller SFF Storage

•1G iSCSI Dual Controller LFF Storage

•1G iSCSI Dual Controller SFF Storage

•10G iSCSI Dual Controller LFF Storage

•10G iSCSI Dual Controller SFF Storage

MSA 1040 front features (24, 2.5 inch drive)

2. Drive in slot 91. Left bezel ear

4. Heartbeat LED3. Fault LED

6. Right bezel ear5. Unit Identification LED

MSA 1040 front features (12, 3.5 inch drives)

2. Drive in slot 41. Left bezel ear

4. Heartbeat LED3. Fault LED

6. Right bezel ear5. Unit Identification LED

Page 1

MSA 1040 rear features

The rear of the MSA 1040 is the same for all MSA

1040 models, except for the SFPs that are pre-installed

in the controller.

NOTE: The pre-installed SFPs shown in the

illustration might not match your environment.

2. Controller module A1. Power supply 1

4. Host ports3. Controller module B

6. Network management port5. CLI port

8. SAS expansion port7. Cache Status LED

9. Power supply 2

Prepare for the installation

Locate required items

The following items are shipped with the MSA 1040:

•HP MSA 1040 chassis. LFF and SFF chassis are

supported.

•Drives

•Rack mounting kit

•Mini-USB CLI cable

•PDU power cords

•HP MSA 1040 SW Support and Documentation

DVD

Other items you may need:

•Screwdrivers (Phillips)

•Antistatic protection device

•Expansion drive enclosures and cables

•Servers that need access to the MSA 1040

•Switch

•Cables for connecting to the host

•RJ-45 Ethernet cable for connecting to a remote

management host

•Access from a workstation on the server to the

MSA 1040 (to access the SMU and validate host

connections)

•Access to the Internet (to access HP websites for

the latest QuickSpecs, user documents, and

firmware)

Obtain the latest user documents

Locate MSA 1040 user guides to help with the

planning, installation, and configuration processes.

User documents are available on the DVD shipped

with the MSA 1040, with the most recent versions on

the MSA 1040 website at http://www.hp.com/

support/msa1040/Manuals.

For detailed reference information, instructions, and

cabling examples, see the following documents:

•HP MSA 1040 QuickSpecs

•HP MSA 1040 User Guide

•HP MSA 1040 Cable Configuration Guide

•HP MSA 1040 SMU Reference Guide

Confirm support for your hardware and software

components

Confirm that the devices you plan to connect and their

installed firmware and software versions are supported

for use with each other. The latest support information

is available on the HP Single Point of Connectivity

Knowledge (SPOCK) website at http://www.hp.com/

storage/spock.

Verify the operating environment

Review the HP MSA 1040 User Guide and ensure that

all environmental requirements are met, including site

wiring and electrical power inputs, ventilation and

cooling, and weight considerations.

Install the MSA 1040

Use the following steps to install your MSA 1040. For

more information, see the HP MSA 1040 User Guide.

Page 2

Step 1. Install device into the rack

Use the instructions provided with the rack mounting

kits or other devices to rack the MSA 1040, expansion

drive enclosures, switches, and servers.

WARNING! At least two people are needed

to lift a fully populated MSA 1040 or expansion

drive enclosure into the rack. If the enclosure is

being loaded into the rack above chest level, a

third person must assist with aligning the

enclosure with the rails, while the other two

people support the weight of the enclosure.

Step 2. Connect expansion drive enclosures

If expansion drive enclosures are included in your

environment, connect SAS cables per their cabling

plan, either straight-through or fault tolerant. Mini-SAS

to Mini-SAS cables are required for each drive

enclosure.

NOTE: The MSA 1040 supports the MSA

2040 LFF Disk Enclosure. There is no MSA

1040-specific disk enclosure.

The following drive enclosures are supported:

DescriptionDrive enclosure model

6Gb SAS 3.5” 12-drive enclosureHP MSA 2040 LFF Disk

Enclosure

6Gb SAS 3.5” 12-drive enclosureHP P2000 LFF Drive

Enclosure

6Gb SAS 2.5” 25-drive enclosureHP D2700 Disk Enclosure

Drive enclosure connection guidelines

•Expansion drive enclosures can be hot-added to

an MSA 1040 that is operating.

•Mini-SAS to Mini-SAS 0.5 m (1.64 ft) cables are

provided with MSA 2040, P2000, and D2700

drive enclosures (one for each I/O module).

•The maximum length cable supported for

connecting drive enclosures is 2 m (6.56 ft).

•Cables longer than those supplied with the drive

enclosure must be purchased separately. For a

list of cables available from HP, see the HP MSA

1040 QuickSpecs.

•The maximum number of enclosures supported in

an MSA 1040 solution is four (one MSA 1040

and up to three expansion drive enclosures).

Example MSA 1040 drive enclosure connections

MSA 1040 firmware supports both fault-tolerant and

straight-through SAS cabling to cascaded drive

enclosures. For more information about these cabling

schemes and for additional cabling examples, see the

HP MSA 1040 Cabling Configuration Guide.

The following image illustrates connecting two D2700

drive enclosures to an MSA 1040 using a

straight-through cabling scheme.

The following image illustrates connecting two D2700

drive enclosures to an MSA 1040 using a fault-tolerant

cabling scheme.

Step 3. Connect the MSA 1040 to data hosts

Direct-connect and switch-connect environments are

supported. For direct-connect configurations, connect

cables from the MSA 1040 to the host. For

switch-connect configurations, connect cables from the

MSA 1040 to the switch ports and from the switch

ports to the hosts.

Page 3

MSA 1040 connection guidelines

•No host interface cables are shipped with MSA

1040 arrays. For a list of cables available from

HP, see the HP MSA 1040 QuickSpecs.

•In direct-connect deployments, connect each host

to the same port on both of the MSA controllers.

•In switch-connect deployments, connect an MSA

Controller A port and the corresponding MSA

Controller B port to one switch, and connect a

second MSA Controller A port and the

corresponding MSA Controller B port to a

separate switch.

Example MSA 1040 connections

The following image illustrates connecting an MSA

1040 FC to two switches, and the two switches

connecting to two servers. Eight Fibre Channel cables

are required.

For more cabling examples, including connecting

directly to a server, see the HP MSA 1040 Cabling

Configuration Guide.

Step 4. Connect the MSA 1040 to a remote

management host (optional)

A remote management host directly manages systems

out-of-band over an Ethernet network.

If a remote management host is included in your

environment, connect an RJ-45 Ethernet cable from the

network management port on each MSA 1040

controller to a switch that your management host can

access (preferably on the same subnet).

Step 5. Connect two Remote Snap-capable MSA

systems to replicate volumes (optional)

The MSA 1040 supports HP MSA Remote Snap

Software, an optional licensed disaster-recovery utility.

This utility performs asynchronous (batch) replication

of block-level data from a volume on a primary MSA

to a secondary volume on the same system or on a

separate, independent MSA system that supports

Remote Snap Software. These two MSA systems

connect through FC or Ethernet switches that are on

the same fabric or network.

For more information about Remote Snap Software,

including cabling requirements and user information,

see the HP MSA 1040 User Guide,HP MSA 1040

SMU Reference Guide, and Remote Snap online help.

Step 6. Connect power cords and power on

devices

IMPORTANT:

•The power cord must be approved for use

in your country. The power cord must be

rated for the product and for the voltage

and current marked on the electrical ratings

label of the product.

•Important safety information about power

cords is available in the Safety and

Disposal Guide, found on the Software

Support/Documentation DVD shipped with

the MSA 1040.

Apply power to the devices in the following order:

1. Connect power cords from the rack to separate

external power sources.

2. Power on the SAN/LAN switches (if necessary).

3. Connect each power supply module in all

attached expansion drive enclosures to a power

source in the rack. If the drive enclosures have

power switches, apply power. If the drive

enclosures do not have power switches, they

automatically start.

4. Wait one minute to ensure that all drives in the

drive enclosure are powered up and ready.

5. Connect each power supply module in the MSA

1040 to a power source in the rack. The MSA

1040 automatically starts (it does not have a

power switch).

6. Observe the LEDs on the front and the rear of the

MSA 1040 and any expansion drive enclosures,

and confirm that no LEDs are amber.

7. Power on the servers (if necessary).

Page 4

Step 7: Update firmware on all components

After installing hardware and powering on devices

for the first time, verify that MSA 1040 controller

modules, expansion drive enclosure I/O modules, and

all disk drives are running the latest available

firmware. If updates are necessary, obtain the firmware

from the HP website and use the SMU to install the

downloaded firmware. For information, see the HP

MSA 1040 SMU Reference Guide.

Step 8: Configure the MSA 1040

Key configuration steps include setting the system date

and time, entering system parameters, configuring

storage volumes, and setting up SNMP trap and email

alert destinations. For more information, see the HP

MSA 1040 SMU Reference Guide.

Helpful websites

MSA 1040 manuals page: http://www.hp.com/

support/msa1040/Manuals

MSA 1040 product page: http://www.hp.com/

support/msa1040

Troubleshooting: http://www.hp.com/support/

msa1040/Troubleshooting

Best practices: http://www.hp.com/support/

msa1040/Bestpractices

QuickSpecs: http://www.hp.com/go/msa1040/

quickspecs

Firmware downloads: http://www.hp.com/support/

downloads

HP SPOCK: http://www.hp.com/storage/spock

Servers: http://www.hp.com/go/servers

Storage Networking: http://www.hp.com/go/san

HP Support Center: http://www.hp.com/go/hpsc

Email notification system

The Subscriber's Choice website includes options to

personalized product tips, update information, driver-

and support-related advisories, and other notices for

this and other HP devices. While optional, HP

recommends registering all of your HP products with

Subscriber's Choice at http://www.hp.com/go/

e-updates.

Warranty statement

Information contained herein is subject to change

without notice. The only warranties for HP products

and services are set forth in the express warranty

statements accompanying such products and services.

Nothing herein should be construed as constituting an

additional warranty. HP shall not be liable for technical

or editorial errors or omissions contained herein.

To obtain a copy of the warranty for this product, see

the warranty information website at http://

www.hp.com/go/storagewarranty.

Documentation feedback

Send any errors, suggestions, or comments to

Documentation Feedback at [email protected].

Page 5

Andere Handbücher für 1040

Inhaltsverzeichnis

Andere HP Lagerung Handbücher

HP AH164A - StorageWorks 1/8 G2 Tape Autoloader Ultrium... Bedienungsanleitung

HP StorageWorks 1510i - Modular Smart Array Bedienungsanleitung

HP StorageWorks XP1024 Kurzanleitung

HP StorageWorks P4000 Series Bedienungsanleitung

HP PERSONAL MEDIA DRIVE Bedienungsanleitung

HP P9000 Bedienungsanleitung

HP LTO-4 Ultrium 1760 Produkthandbuch

HP StorageWorks 600 - Modular Disk System Handbuch

HP Surestore E Tape Library Model 2/20 Bedienungsanleitung

HP StoreOnce B6000 Bedienungsanleitung

HP StorageWorks 8000 - NAS Bedienungsanleitung

HP C7745NB - SureStore DLT Tape Autoloader 1/9 Bedienungsanleitung

HP NetServer Common Tray Ultra3 Bedienungsanleitung

HP Xw6600 - Workstation - 2 GB RAM Bedienungsanleitung

HP 3PAR StoreServ 7200 2-node Bedienungsanleitung

HP Surestore Disk Array 12h - And FC60 Bedienungsanleitung

HP 3000 - 37XE System Bedienungsanleitung

HP Surestore 160ex - Optical Jukebox Bedienungsanleitung

HP P2000 G3 Bedienungsanleitung

HP StorageWorks 2100 - Disk System Bedienungsanleitung

HP 705 Workstation Bedienungsanleitung

HP Invent EH861 Series Montageanleitung

HP P9000 Bedienungsanleitung

HP StorageWorks P4000 Series Firmware-Update

Beliebte Lagerung Handbücher anderer Marken

QNAP

QNAP TS 32PXU Series Bedienungsanleitung

LaCie

LaCie RUGGED RAID Bedienungsanleitung

Freecom

Freecom CLS DOCK Bedienungsanleitung

PNY

PNY Attache P-FD64MBATT3 Bedienungsanleitung

OLT

OLT 6x6 Maximizer Bedienungsanleitung

Transcend

Transcend JetFlash 160 Bedienungsanleitung

LaCie

LaCie RUGGED MINI Bedienungsanleitung

Thunderbolt

Thunderbolt 600 Bedienungsanleitung

Panasonic

Panasonic LB-DH8 series Handbuch

Intel

Intel RAID High Availability Bedienungsanleitung

LaCie

LaCie 12big Thunderbolt 3 Bedienungsanleitung

Spectra Logic

Spectra Logic T-Series Spectra T50e Bedienungsanleitung

Panasonic

Panasonic LKM-F931-1 Bedienungsanleitung

Tabernus

Tabernus Enterprise Erase E2400 Bedienungsanleitung

Rocstor

Rocstor COMMANDER 3F series Bedienungsanleitung

Western Digital

Western Digital Ultrastar Data60 Bedienungsanleitung

Dell

Dell PowerVault MD3600f Series Bedienungsanleitung

CFI

CFI TERA STOR SATA RAID IV Bedienungsanleitung