HP 4X Bedienungsanleitung

HP 4x SFF hard disk

drive installation kit

Company, L.P.

Printed in

698526-001

Introduction

This document describes how to install a small form factor

(SFF) hard disk drive (HDD) carrier in the optical disk drive

(ODD) bay of the HP Z620 and Z820 Workstations.

Kit contents

•4x carrier

•16 counter-sunk screws

•8 locking screws (not needed on Z620 or Z820)

•Three-way splitter power cable

•Installation instructions (this document)

Required tools

•Phillips screwdriver

WARNING! These symbols on any surface or area of

the equipment indicate the following:

Presence of a hot surface or hot component. If this

surface is contacted, the potential for injury exists. To

reduce the risk of injury from a hot component, let the

surface cool before touching.

Presence of an electrical shock hazard. To reduce the

risk of injury from electrical shock, do not open any

enclosed area marked with this symbol.

Product must always be lifted by two persons to avoid

personal injury due to product weight.

WARNING! To reduce the risk of electric shock or

damage to your equipment:

— Do not disable the power cord grounding plug. The

grounding plug is an important safety feature.

— Plug the power cord in a grounded (earthed) outlet

that is easily accessible at all times.

— Disconnect power from the equipment by

unplugging the power cord from the electrical outlet.

WARNING! To reduce the risk of serious injury, read

the Safety & Comfort Guide. It describes proper

computer setup, posture, health, and work habits for

computer users, and provides important electrical and

mechanical safety information. This guide is located at

http://www.hp.com/ergo.

WARNING! Do not use the front bezel as a handle or

lifting point when lifting or moving the computer.

Lifting the computer from the front bezel, or lifting it

incorrectly, might cause the computer to fall, resulting

in possible injury to you and damage to the computer.

To properly and safely move the computer, lift from the

bottom of the computer.

CAUTION: Static electricity can damage the electronic

components of the computer or optional equipment.

Before beginning this procedure, ensure that you are

static-free by briefly touching a grounded metal object.

To prevent damage to the computer, observe the

following Electrostatic Discharge (ESD) precautions

while performing the system parts removal and

replacement procedures:

— Work on a static-free mat.

— Wear a static strap to ensure that any accumulated

electrostatic charge is discharged from your body to

the ground.

— Create a common ground for the equipment you

are working on by connecting the static-free mat, a

static strap, and peripheral units to that piece of

equipment.

Step 1—Preparing for installation

1. If you need help preparing the computer for this

installation, refer to the:

• Removal and replacement videos for your

computer at http://www.hp.com/go/sml or

•Maintenance and Service Guide for your

computer at http://www.hp.com/support/

computer manuals.

2. Power down the computer, then disconnect the power

cord.

3. Power down all external devices, then disconnect them

from the computer.

4. Remove the side access panel.

NOTE: Install the SFF hard disk drives in the in

the lower ODD bay first.

5. If necessary, remove the ODD filler tray.

a. Lift and hold the green release lever for the optical

bay (1) while sliding the ODD filler tray out of the

bay (2).

b. When the rear of the tray is near the edge of the

bay, release the latch, but continue to slide the

tray outward.

Figure 1 Removing the ODD filler tray

6. If an optical disk drive is present, remove it.

a. Disconnect the power cable and data cable from

the rear of the ODD.

b. Lift and hold the green release lever for the optical

bay while sliding the ODD out of the bay. When

the rear of the ODD is near the edge of the bay,

release the latch, but continue to slide the drive

outward.

HP 4x SFF hard disk

drive installation kit

Company, L.P.

Printed in

698526-001

Introduction

This document describes how to install a small form factor

(SFF) hard disk drive (HDD) carrier in the optical disk drive

(ODD) bay of the HP Z620 and Z820 Workstations.

Kit contents

•4x carrier

•16 counter-sunk screws

•8 locking screws (not needed on Z620 or Z820)

•Three-way splitter power cable

•Installation instructions (this document)

Required tools

•Phillips screwdriver

WARNING! These symbols on any surface or area of

the equipment indicate the following:

Presence of a hot surface or hot component. If this

surface is contacted, the potential for injury exists. To

reduce the risk of injury from a hot component, let the

surface cool before touching.

Presence of an electrical shock hazard. To reduce the

risk of injury from electrical shock, do not open any

enclosed area marked with this symbol.

Product must always be lifted by two persons to avoid

personal injury due to product weight.

WARNING! To reduce the risk of electric shock or

damage to your equipment:

— Do not disable the power cord grounding plug. The

grounding plug is an important safety feature.

— Plug the power cord in a grounded (earthed) outlet

that is easily accessible at all times.

— Disconnect power from the equipment by

unplugging the power cord from the electrical outlet.

WARNING! To reduce the risk of serious injury, read

the Safety & Comfort Guide. It describes proper

computer setup, posture, health, and work habits for

computer users, and provides important electrical and

mechanical safety information. This guide is located at

http://www.hp.com/ergo.

WARNING! Do not use the front bezel as a handle or

lifting point when lifting or moving the computer.

Lifting the computer from the front bezel, or lifting it

incorrectly, might cause the computer to fall, resulting

in possible injury to you and damage to the computer.

To properly and safely move the computer, lift from the

bottom of the computer.

CAUTION: Static electricity can damage the electronic

components of the computer or optional equipment.

Before beginning this procedure, ensure that you are

static-free by briefly touching a grounded metal object.

To prevent damage to the computer, observe the

following Electrostatic Discharge (ESD) precautions

while performing the system parts removal and

replacement procedures:

— Work on a static-free mat.

— Wear a static strap to ensure that any accumulated

electrostatic charge is discharged from your body to

the ground.

— Create a common ground for the equipment you

are working on by connecting the static-free mat, a

static strap, and peripheral units to that piece of

equipment.

Step 1—Preparing for installation

1. If you need help preparing the computer for this

installation, refer to the:

• Removal and replacement videos for your

computer at http://www.hp.com/go/sml or

•Maintenance and Service Guide for your

computer at http://www.hp.com/support/

computer manuals.

2. Power down the computer, then disconnect the power

cord.

3. Power down all external devices, then disconnect them

from the computer.

4. Remove the side access panel.

NOTE: Install the SFF hard disk drives in the in

the lower ODD bay first.

5. If necessary, remove the ODD filler tray.

a. Lift and hold the green release lever for the optical

bay (1) while sliding the ODD filler tray out of the

bay (2).

b. When the rear of the tray is near the edge of the

bay, release the latch, but continue to slide the

tray outward.

Figure 1 Removing the ODD filler tray

6. If an optical disk drive is present, remove it.

a. Disconnect the power cable and data cable from

the rear of the ODD.

b. Lift and hold the green release lever for the optical

bay while sliding the ODD out of the bay. When

the rear of the ODD is near the edge of the bay,

release the latch, but continue to slide the drive

outward.

HP 4x SFF hard disk

drive installation kit

Company, L.P.

Printed in

698526-001

Introduction

This document describes how to install a small form factor

(SFF) hard disk drive (HDD) carrier in the optical disk drive

(ODD) bay of the HP Z620 and Z820 Workstations.

Kit contents

•4x carrier

•16 counter-sunk screws

•8 locking screws (not needed on Z620 or Z820)

•Three-way splitter power cable

•Installation instructions (this document)

Required tools

•Phillips screwdriver

WARNING! These symbols on any surface or area of

the equipment indicate the following:

Presence of a hot surface or hot component. If this

surface is contacted, the potential for injury exists. To

reduce the risk of injury from a hot component, let the

surface cool before touching.

Presence of an electrical shock hazard. To reduce the

risk of injury from electrical shock, do not open any

enclosed area marked with this symbol.

Product must always be lifted by two persons to avoid

personal injury due to product weight.

WARNING! To reduce the risk of electric shock or

damage to your equipment:

— Do not disable the power cord grounding plug. The

grounding plug is an important safety feature.

— Plug the power cord in a grounded (earthed) outlet

that is easily accessible at all times.

— Disconnect power from the equipment by

unplugging the power cord from the electrical outlet.

WARNING! To reduce the risk of serious injury, read

the Safety & Comfort Guide. It describes proper

computer setup, posture, health, and work habits for

computer users, and provides important electrical and

mechanical safety information. This guide is located at

http://www.hp.com/ergo.

WARNING! Do not use the front bezel as a handle or

lifting point when lifting or moving the computer.

Lifting the computer from the front bezel, or lifting it

incorrectly, might cause the computer to fall, resulting

in possible injury to you and damage to the computer.

To properly and safely move the computer, lift from the

bottom of the computer.

CAUTION: Static electricity can damage the electronic

components of the computer or optional equipment.

Before beginning this procedure, ensure that you are

static-free by briefly touching a grounded metal object.

To prevent damage to the computer, observe the

following Electrostatic Discharge (ESD) precautions

while performing the system parts removal and

replacement procedures:

— Work on a static-free mat.

— Wear a static strap to ensure that any accumulated

electrostatic charge is discharged from your body to

the ground.

— Create a common ground for the equipment you

are working on by connecting the static-free mat, a

static strap, and peripheral units to that piece of

equipment.

Step 1—Preparing for installation

1. If you need help preparing the computer for this

installation, refer to the:

• Removal and replacement videos for your

computer at http://www.hp.com/go/sml or

•Maintenance and Service Guide for your

computer at http://www.hp.com/support/

computer manuals.

2. Power down the computer, then disconnect the power

cord.

3. Power down all external devices, then disconnect them

from the computer.

4. Remove the side access panel.

NOTE: Install the SFF hard disk drives in the in

the lower ODD bay first.

5. If necessary, remove the ODD filler tray.

a. Lift and hold the green release lever for the optical

bay (1) while sliding the ODD filler tray out of the

bay (2).

b. When the rear of the tray is near the edge of the

bay, release the latch, but continue to slide the

tray outward.

Figure 1 Removing the ODD filler tray

6. If an optical disk drive is present, remove it.

a. Disconnect the power cable and data cable from

the rear of the ODD.

b. Lift and hold the green release lever for the optical

bay while sliding the ODD out of the bay. When

the rear of the ODD is near the edge of the bay,

release the latch, but continue to slide the drive

outward.

Step 2—Installing the SFF hard drives in the

4x carrier

NOTE: The HP Z820 Workstation supports two

4x carriers (eight SFF hard drives). The HP Z620

Workstation supports one 4x carrier (four SFF

hard drives).

1. To install the SFF drives into the carrier, follow

directions provided by manufacturer. Install the SFF

drives, starting at the upper row, then the lower row,

moving left-to-right.

Figure 2 Order of SFF drive install

2. Install up to four SFF drives in each carrier.

Step 3—Installing 4x carrier in ODD bay

1. Before installing the carrier into the workstation ODD

bay, attach the power cables to the back of the 4x

carrier and to the workstation power cable.

a. Attach the power cables to support the drives in

the carrier, as needed. The upper plug on the 4x

carrier (1), supports the upper row of drives, and

the lower plug (2) supports the lower row of

drives.

Figure 3 Power cables installation order

b. Plug the female ends of the power cables (1) and

(2) into back of the carrier, and male end of the

power cable (4) to the workstation power cable.

The remaining power connector (3) is not used.

Figure 4 Attaching power cables

c. Plug the end of the carrier power cable (4) into

the workstation power cable (5).

NOTE: When installing the 4x carrier in the ODD

bay, install in the lower bay first.

Figure 5 Connecting power cables

2. Lift and hold the green release lever for the optical bay

(1) while sliding the 4x carrier into the bay (2) until an

audible click sounds.

Figure 6 Installing the 4x carrier

3. Attach the SATA cables to the rear of the carrier.

Attach the upper row first, then the lower row, moving

from right-to-left.

Figure 7 Attaching SATA cables

Step 4—Reassembling the computer

1. Reinstall the side access panel.

2. Reconnect power to the computer and all external

devices.

3. Restore power to the computer and all external

devices.

Step 2—Installing the SFF hard drives in the

4x carrier

NOTE: The HP Z820 Workstation supports two

4x carriers (eight SFF hard drives). The HP Z620

Workstation supports one 4x carrier (four SFF

hard drives).

1. To install the SFF drives into the carrier, follow

directions provided by manufacturer. Install the SFF

drives, starting at the upper row, then the lower row,

moving left-to-right.

Figure 2 Order of SFF drive install

2. Install up to four SFF drives in each carrier.

Step 3—Installing 4x carrier in ODD bay

1. Before installing the carrier into the workstation ODD

bay, attach the power cables to the back of the 4x

carrier and to the workstation power cable.

a. Attach the power cables to support the drives in

the carrier, as needed. The upper plug on the 4x

carrier (1), supports the upper row of drives, and

the lower plug (2) supports the lower row of

drives.

Figure 3 Power cables installation order

b. Plug the female ends of the power cables (1) and

(2) into back of the carrier, and male end of the

power cable (4) to the workstation power cable.

The remaining power connector (3) is not used.

Figure 4 Attaching power cables

c. Plug the end of the carrier power cable (4) into

the workstation power cable (5).

NOTE: When installing the 4x carrier in the ODD

bay, install in the lower bay first.

Figure 5 Connecting power cables

2. Lift and hold the green release lever for the optical bay

(1) while sliding the 4x carrier into the bay (2) until an

audible click sounds.

Figure 6 Installing the 4x carrier

3. Attach the SATA cables to the rear of the carrier.

Attach the upper row first, then the lower row, moving

from right-to-left.

Figure 7 Attaching SATA cables

Step 4—Reassembling the computer

1. Reinstall the side access panel.

2. Reconnect power to the computer and all external

devices.

3. Restore power to the computer and all external

devices.

Step 2—Installing the SFF hard drives in the

4x carrier

NOTE: The HP Z820 Workstation supports two

4x carriers (eight SFF hard drives). The HP Z620

Workstation supports one 4x carrier (four SFF

hard drives).

1. To install the SFF drives into the carrier, follow

directions provided by manufacturer. Install the SFF

drives, starting at the upper row, then the lower row,

moving left-to-right.

Figure 2 Order of SFF drive install

2. Install up to four SFF drives in each carrier.

Step 3—Installing 4x carrier in ODD bay

1. Before installing the carrier into the workstation ODD

bay, attach the power cables to the back of the 4x

carrier and to the workstation power cable.

a. Attach the power cables to support the drives in

the carrier, as needed. The upper plug on the 4x

carrier (1), supports the upper row of drives, and

the lower plug (2) supports the lower row of

drives.

Figure 3 Power cables installation order

b. Plug the female ends of the power cables (1) and

(2) into back of the carrier, and male end of the

power cable (4) to the workstation power cable.

The remaining power connector (3) is not used.

Figure 4 Attaching power cables

c. Plug the end of the carrier power cable (4) into

the workstation power cable (5).

NOTE: When installing the 4x carrier in the ODD

bay, install in the lower bay first.

Figure 5 Connecting power cables

2. Lift and hold the green release lever for the optical bay

(1) while sliding the 4x carrier into the bay (2) until an

audible click sounds.

Figure 6 Installing the 4x carrier

3. Attach the SATA cables to the rear of the carrier.

Attach the upper row first, then the lower row, moving

from right-to-left.

Figure 7 Attaching SATA cables

Step 4—Reassembling the computer

1. Reinstall the side access panel.

2. Reconnect power to the computer and all external

devices.

3. Restore power to the computer and all external

devices.

Inhaltsverzeichnis

Andere HP Lagerung Handbücher

HP StorageWorks 8000 - NAS Bedienungsanleitung

HP A2W75-67905 Bedienungsanleitung

HP StorageWorks 2000i Bedienungsanleitung

HP AD510A - StorageWorks Modular Smart Array 1500 cs 2U Fibre Channel SAN Attach Controller Shelf Hard... Bedienungsanleitung

HP 3PAR StoreServ 7200 2-node Bedienungsanleitung

HP Surestore E Tape Library Model 2/20 Bedienungsanleitung

HP AD510A - StorageWorks Modular Smart Array 1500 cs 2U Fibre Channel SAN Attach Controller Shelf Hard... Handbuch

HP Compaq Pro 6305 Bedienungsanleitung

HP StorageWorks 4000/6000/8000 - Enterprise Virtual... Bedienungsanleitung

HP D6030A - NetServer - E50 Bedienungsanleitung

HP StoreAll 9730 Service-Handbuch

HP Surestore Disk Array 12h - And FC60 Bedienungsanleitung

HP AH164A - StorageWorks 1/8 G2 Tape Autoloader Ultrium... Bedienungsanleitung

HP 201723-B21 - HP StorageWorks Modular SAN Array 1000 Hard... Bedienungsanleitung

HP v119r Bedienungsanleitung

HP StorageWorks SDLT 600 Installationsanleitung

HP Surestore Tape Library Model 10/588 Montageanleitung

HP StorageWorks NAS b2000 - v2 Bedienungsanleitung

HP EX950 M.2 Bedienungsanleitung

HP SAS Bedienungsanleitung

HP 3PAR StoreServ 7000 Bedienungsanleitung

HP D2D Bedienungsanleitung

HP Surestore Disk Array 12h - And FC60 Montageanleitung

HP 705 Kurzanleitung

Beliebte Lagerung Handbücher anderer Marken

QNAP

QNAP TS 32PXU Series Bedienungsanleitung

LaCie

LaCie RUGGED RAID Bedienungsanleitung

Freecom

Freecom CLS DOCK Bedienungsanleitung

PNY

PNY Attache P-FD64MBATT3 Bedienungsanleitung

OLT

OLT 6x6 Maximizer Bedienungsanleitung

Transcend

Transcend JetFlash 160 Bedienungsanleitung

LaCie

LaCie RUGGED MINI Bedienungsanleitung

Thunderbolt

Thunderbolt 600 Bedienungsanleitung

Panasonic

Panasonic LB-DH8 series Handbuch

Intel

Intel RAID High Availability Bedienungsanleitung

LaCie

LaCie 12big Thunderbolt 3 Bedienungsanleitung

Spectra Logic

Spectra Logic T-Series Spectra T50e Bedienungsanleitung

Panasonic

Panasonic LKM-F931-1 Bedienungsanleitung

Tabernus

Tabernus Enterprise Erase E2400 Bedienungsanleitung

Rocstor

Rocstor COMMANDER 3F series Bedienungsanleitung

Western Digital

Western Digital Ultrastar Data60 Bedienungsanleitung

Dell

Dell PowerVault MD3600f Series Bedienungsanleitung

CFI

CFI TERA STOR SATA RAID IV Bedienungsanleitung