HP D6030A - NetServer - E50 Bedienungsanleitung

HP NetServer

Common Tray Ultra3

Hard Disk Drive

Installation Guide

HP Part Number 5969-5921

Printed in February 2000

Notice

The information contained in this document is subject to change without notice.

Hewlett-Packard makes no warranty of any kind with regard to this

material, including, but not limited to, the implied warranties of

merchantability and fitness for a particular purpose. Hewlett-Packard shall

not be liable for errors contained herein or for incidental or consequential

damages in connection with the furnishing, performance, or use of this material.

Hewlett-Packard assumes no responsibility for the use or reliability of its software

on equipment that is not furnished by Hewlett-Packard.

This document contains proprietary information that is protected by copyright.

All rights are reserved. No part of this document may be photocopied,

reproduced, or translated to another language without the prior written consent of

Hewlett-Packard Company.

NetWare®and UnixWare®are registered trademarks of Novell, Inc. Microsoft®

Windows NT, NTAS®, MS-DOS and Windows 2000®are registered trademarks

of Microsoft Corporation. SCO®UNIX®is a registered trademark of The Santa

Cruz Operation, Inc. Banyan®and VINES®are the registered trademark of

Banyan Systems Incorporated. OS/2is the registered trademark of the

International Business Machines Corporation. 3M® is a registered trademark of

Minnesota Mining and Manufacturing Company. TorxTM is a registered

trademark of CamCar/Textron, Inc. SCSI SelectTM is a registered trademark of

Adaptec, Inc. Linux®is a registered trademark of Linus Torvalds.

Hewlett-Packard Company

Network Server Division

Technical Communications/MS 45SLE

10955 Tantau Avenue

Cupertino, CA 95014 USA

Audience Assumptions

This guide is for the person who installs, administers, and troubleshoots LAN

servers. Hewlett-Packard Company assumes you are qualified in the servicing of

computer equipment and trained in recognizing hazards in products with

hazardous energy levels.

iii

Contents

1 Prepare Drive for Installation...................................................................... 1

Introduction ................................................................................................... 1

General Installation Steps.......................................................................... 1

Step 1: Prepare for Installation ...................................................................... 2

Tools You Need......................................................................................... 2

Setup Information You Need ..................................................................... 2

Unpack the Drive....................................................................................... 3

Step 2: Determine the Drive Type ................................................................. 3

Step 3: Set the SCSI Address........................................................................ 6

Step 4: Connect SCSI Cable Adapter (if required)....................................... 10

Step 5: Continue Installation........................................................................ 10

2 Mount the Drive in the NetServer L Series............................................... 11

Step 1: Mount the Drive in the System ........................................................ 11

Step 2: Connect the Drive Activity Light ...................................................... 12

Step 3: Connect the Drive ........................................................................... 14

Step 4: Configure the Drive......................................................................... 15

3 Mount the Drive in the NetServer E 45 or E 50......................................... 17

Step 1: Determine the Drive Location.......................................................... 17

Step 2: Mount the Drive in the System ........................................................ 19

Mount the Drive in Shelf 5 or 6................................................................ 19

Mount the Drive in Shelf 3 or 4................................................................ 19

Step 3: Connect the Drive ........................................................................... 20

Step 4: Configure the Drive......................................................................... 21

A Jumper Settings........................................................................................ 23

Jumper Legend ........................................................................................... 23

B Disk Drive Characteristics......................................................................... 25

C Returning HP Hard Disk Drives ................................................................ 27

D Warranty and Support............................................................................... 29

Hardware Warranty ..................................................................................... 29

HP Repair and Telephone Support.............................................................. 29

E Regulatory Information............................................................................. 31

Contents

Index............................................................................................................... 33

1 Prepare Drive for Installation

Introduction

This chapter describes the tools, setup information and the steps necessary to

install a SCSI hard disk drive into an HP NetServer. The drives documented in

this guide are listed in Table 1-1.

Table 1-1. Hard Disk Drive Product Numbers

HP Product Number Capacity RPM

P1213A 9.10 GB 7200

P1214A 9.10 GB 10000

P1215A 18.2 GB 7200

P1167A 18.2 GB 10000

P1169A 36.4 GB 10000

1If you are using a narrow50-pin cable(part number 5182-4551) when connecting to a HP NetServer

E45, a 68-50 pin adapter will also be needed

These HP Ultra3 drives can operate in either Single-Ended (SE) mode as Ultra

drives with a maximum bus data rate of 40 MB or in Low-Voltage Differential

(LVD) mode as Ultra3 drives with a maximum bus data rate of 160 MB. The

terminator on the cable, other drives on the bus, and/or the host controller card,

determines whether the drive runs in SE or LVD mode.

NOTE For any drive to run in LVD mode, all SCSI components on

that bus must be in LVD mode.

General Installation Steps

In general, the steps for installing a hard drive are shown below. Please refer to

the detailed instructions in each step before attempting to install your drive.

1. Prepare for Installation

2. Determine the Drive Type

3. Set the SCSI Address

4. Connect SCSI Cable Adapter (if required)

5. Mount the Drive in the System

6. Connect the Drive Activity Light (if appropriate)

7. Connect the Drive

8. Configure the Drive

Chapter 1 Prepare Drive for Installation

CAUTION In a few cases, drives with the same product number can be of

different types and require different jumper settings. If your

drive does not match the type in the figure, check the other

figures for the matching type.

Step 1: Prepare for Installation

Gather the tools and the setup information you need to install the drive, before

removing the drive from its packaging.

Tools You Need

To install the disk drive, you need the following tools:

•Tweezers, needle-nose pliers or a similar tool for setting configuration

jumpers.

•A TorxTM T-15 screwdriver or a regular blade screwdriver.

Setup Information You Need

Before you begin, you need the following setup information:

•The HP NetServer Installation Road Map for your system or Information

Assistant on the HP NetServer Navigator CD-ROM.

•The SCSI addresses available in your system. (Refer to your system in

Information Assistant on the HP NetServer Navigator CD-ROM for

information on determining available SCSI addresses.)

Chapter 1 Prepare Drive for Installation

Unpack the Drive

CAUTION Shock: Hard disk drives are very susceptible to mechanical

shock and can be damaged by a drop as short as one-quarter

of an inch (.64 cm). Take care when unpacking and handling

the disk drive. If the drop would crack an egg, it will damage

the drive.

Static: Protect the hard disk drive from static electricity by

leaving it in its antistatic bag until you are ready to install it.

Use an antistatic wrist strap and a grounding mat (3M

8501/8502/8505 or equivalent). If an antistatic work area is

not available, touch any unpainted metal surface to discharge

static electricity before handling the drive.

When you remove the hard disk drive from the antistatic bag,

handle it only by the frame. Do not touch the electrical

components. Place the drive on the antistatic bag whenever

you set it down.

After gathering the information and tools:

•Remove the drive from the packaging.

Step 2: Determine the Drive Type

The type of the drive varies and drives with the same part number may be of

different types.

•Match the drive you unpacked with the type of drive shown in Figure 1-1.

Chapter 1 Prepare Drive for Installation

Type 1

P1213A 9.10 GB Model

P1214A 9.10 GB Model

P1215A 18.2 GB Model

P1167A 18.2 GB Model

P1169A 36.4 GB Model

Type 2

P1213A 9.10 GB Model

P1214A 9.10 GB Model

P1215A 18.2 GB Model

P1167A 18.2 GB Model

P1169A 36.4 GB Model

Type 3

P1213A 9.10 GB Model

P1214A 9.10 GB Model

P1215A 18.2 GB Model

P1167A 18.2 GB Model

P1169A 36.4 GB Model

Figure 1-1. Identification of the Three Different Types of Drives

NOTE Some of the product numbers are duplicated, because the type

of drive shipped is not always the same. Therefore, it is

important that you match your drive to the correct type.

The types of drives differ in that the jumpers are in different locations. Refer to

the appropriate illustration (Figure 1-2, 1-3, or 1-4) for your type of drive, and

note the location of the jumpers.

Chapter 1 Prepare Drive for Installation

The "Disk Drive Characteristics" appendix shows a legend of the drive control

settings and the jumper control settings for the individual drives.

SCSI

Connector

Figure 1-2. Component Identification, Type 1 Drives

SCSI

Connector

Power

Connector

Figure 1-3. Component Identification, Type 2 Drives

Chapter 1 Prepare Drive for Installation

SCSI

Connector

Power

Connector

CN2N2

Figure 1-4. Component Identification, Type 3 Drives

Step 3: Set the SCSI Address

The SCSI address is set using jumpers located on the drive. SCSI addresses range

from 0 to 15.

•Each drive is preset to SCSI address 3.

•Address 7 is reserved for communications with the SCSI host bus adapter.

Set the drive to the lowest available SCSI address. Address 0 should be used for

the first drive in the system. Typically, address 1 is assigned to the second hard

disk drive, address 2 is assigned to the third drive, and so forth.

This step assumes the jumpers are accessible. If they are not accessible, it may be

necessary to remove the mounting tray or bracket to adjust the settings.

Each device on the channel needs a different SCSI address. If this is the first

hard drive in the system, complete this step to verify the jumper is set correctly. If

this is one of two or more SCSI devices in the system (and not the first drive),

you must change the SCSI address for the drive.

•If you are connecting an Ultra3 SCSI drive to a narrow SCSI cable1and

narrow SCSI controller, set the SCSI address to 0, 1, 2, or 3.

•If you are connecting an Ultra3 SCSI drive to a wide SCSI cable and wide

SCSI controller, set the SCSI address to 0, 1, 2, 3, 4, 5, or 6.

Detailed descriptions of all the jumpers are provided in the "Jumper Settings"

appendix. Figures 1-7, 1-8, 1-9, 1-10 and 1-11 show the default SCSI address

settings for each drive.

1When connecting to a HP NetServer E45, a 68-50 pin adapter will also be needed.

Andere Handbücher für D6030A - NetServer - E50

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere HP Lagerung Handbücher

HP StoreOnce B6000 Bedienungsanleitung

HP BAAD0010HBK-NHSN Bedienungsanleitung

HP Pavilion p6000 - Desktop PC Bedienungsanleitung

HP StorageWorks ESL E Series Gebrauchs- und Pflegehandbuch

HP 5243-2SE Bedienungsanleitung

HP P9000 Bedienungsanleitung

HP IBRIX X9720 Service-Handbuch

HP StorageWorks XP12000 Bedienungsanleitung

HP AJ765A - StorageWorks RDX Removable Disk Backup... Bedienungsanleitung

HP 8505 8mm Cartridge Tape Drive EK-STWCT-UG.... Bedienungsanleitung

HP StorageWorks 3000 - RAID Array Kurzanleitung

HP D2D Bedienungsanleitung

HP StorageWorks 1900ux Bedienungsanleitung

HP StorageWorks 4000/6000/8000 - Enterprise Virtual... Bedienungsanleitung

HP 201723-B21 - HP StorageWorks Modular SAN Array 1000 Hard... Bedienungsanleitung

HP C4405A - Colorado 14GB Tape Drive Bedienungsanleitung

HP SimpleSave Bedienungsanleitung

HP mv2040 Bedienungsanleitung

HP StoreAll 9730 Service-Handbuch

HP StorageWorks XP1024 Kurzanleitung

HP D2D Bedienungsanleitung

HP StorageWorks P4000 Series Bedienungsanleitung

HP C6388B Bedienungsanleitung

HP P9000 Kurzanleitung zur Einrichtung

Beliebte Lagerung Handbücher anderer Marken

QNAP

QNAP TS 32PXU Series Bedienungsanleitung

LaCie

LaCie RUGGED RAID Bedienungsanleitung

Freecom

Freecom CLS DOCK Bedienungsanleitung

PNY

PNY Attache P-FD64MBATT3 Bedienungsanleitung

OLT

OLT 6x6 Maximizer Bedienungsanleitung

Transcend

Transcend JetFlash 160 Bedienungsanleitung

LaCie

LaCie RUGGED MINI Bedienungsanleitung

Thunderbolt

Thunderbolt 600 Bedienungsanleitung

Panasonic

Panasonic LB-DH8 series Handbuch

Intel

Intel RAID High Availability Bedienungsanleitung

LaCie

LaCie 12big Thunderbolt 3 Bedienungsanleitung

Spectra Logic

Spectra Logic T-Series Spectra T50e Bedienungsanleitung

Panasonic

Panasonic LKM-F931-1 Bedienungsanleitung

Tabernus

Tabernus Enterprise Erase E2400 Bedienungsanleitung

Rocstor

Rocstor COMMANDER 3F series Bedienungsanleitung

Western Digital

Western Digital Ultrastar Data60 Bedienungsanleitung

Dell

Dell PowerVault MD3600f Series Bedienungsanleitung

CFI

CFI TERA STOR SATA RAID IV Bedienungsanleitung