HP NetStorage 6000 Bedienungsanleitung

Andere Handbücher für NetStorage 6000

12

Andere HP Lagerung Handbücher

HP

HP IBRIX X9720 Service-Handbuch

HP

HP Surestore Disk Array 12h - And FC60 Bedienungsanleitung

HP

HP XP7 Bedienungsanleitung

HP

HP StorageWorks Modular Smart Array 500 System Bedienungsanleitung

HP

HP Surestore Disk Array 12h - And FC60 Bedienungsanleitung

HP

HP StorageWorks NAS 8000 - Version 1.6.X Betriebsanleitung

HP

HP StoreOnce B6000 Betriebsanleitung

HP

HP StorageWorks 1000 - Modular Smart Array Gebrauchs- und Pflegehandbuch

HP

HP P9000 Bedienungsanleitung

HP

HP 9130K Bedienungsanleitung

HP

HP StoreOnce 3100 Handbuch

HP

HP C7401A - SureStore Ultrium 230 Tape Drive Bedienungsanleitung

HP

HP 88780B Bedienungsanleitung

HP

HP StorageWorks 8B - FC Entry Switch Bedienungsanleitung

HP

HP StorageWorks 1/8 G2 Bedienungsanleitung

HP

HP D6000 Disk Enclosure Handbuch

HP

HP Surestore 64 - Director Switch Bedienungsanleitung

HP

HP ProLiant StorageWorks NAS 1500s Bedienungsanleitung

HP

HP LTO-4 Ultrium 1760 Produkthandbuch

HP

HP StorageWorks 1000 - Modular Smart Array Service-Handbuch

HP

HP StorageWorks 2000 Series Bedienungsanleitung

HP

HP SmartMemory Bedienungsanleitung

HP

HP MSA 2040 Bedienungsanleitung

HP

HP StorageWorks 4000/6000/8000 - Enterprise Virtual... Bedienungsanleitung

Beliebte Lagerung Handbücher anderer Marken

QNAP

QNAP TS 32PXU Series Bedienungsanleitung

LaCie

LaCie RUGGED RAID Bedienungsanleitung

Freecom

Freecom CLS DOCK Bedienungsanleitung

PNY

PNY Attache P-FD64MBATT3 Bedienungsanleitung

OLT

OLT 6x6 Maximizer Bedienungsanleitung

Transcend

Transcend JetFlash 160 Bedienungsanleitung

LaCie

LaCie RUGGED MINI Bedienungsanleitung

Thunderbolt

Thunderbolt 600 Bedienungsanleitung

Panasonic

Panasonic LB-DH8 series Handbuch

Intel

Intel RAID High Availability Bedienungsanleitung

LaCie

LaCie 12big Thunderbolt 3 Bedienungsanleitung

Spectra Logic

Spectra Logic T-Series Spectra T50e Bedienungsanleitung

Panasonic

Panasonic LKM-F931-1 Bedienungsanleitung

Tabernus

Tabernus Enterprise Erase E2400 Bedienungsanleitung

Rocstor

Rocstor COMMANDER 3F series Bedienungsanleitung

Western Digital

Western Digital Ultrastar Data60 Bedienungsanleitung

Dell

Dell PowerVault MD3600f Series Bedienungsanleitung

CFI

CFI TERA STOR SATA RAID IV Bedienungsanleitung

Network Interface Upgrade

HP NETSTORAGE 6000

Configurations supported:

Any combination of one or two of the following

HP NICs is supported:

•10/100 b

•Dual 10/100 b

•Gigabit 1000 Base SX

Each NIC port must be attached to a different subnet.

runking is not supported.

Parts required:

•New NIC card

Tools required:

•Phillips screwdriver

•Electrostatic protection device

NOTES:

•Use only HP NetStorage 6000 Network Interface Cards for upgrades.

•For this upgrade, you should choose a time when end-user access is not required for the unit.

Shut own the System

Open the Case

A. Remove the two screws on the back of the unit that hold

the top in place.

B. Slide the top backwards, and lift to remove.

A. Shut down the unit using either the front panel interface

or the HP NetStorage web interface.

B. After system shutdown is complete, turn off the power

switch on the back panel of the unit.

C. Disconnect both power cords from the back panel of the

unit.

All manuals and user guides at all-guides.com

all-guides.com

A. Unplug the network cable.

B. Unscrew the existing NIC and gently remove it.

NOTE: If you are installing the NIC in an unused PCI slot,

remove the expansion slot access panel.

A. Select an open PCI slot.

B. Gently place the new card in the slot, and screw it into

place.

A. Slide the top back into place.

B. Using the screwdriver, secure the top to the unit.

Add or Remove a NIC Card

Insert the New Card

Close the Case

A.

B.

All manuals and user guides at all-guides.com

Connect the Unit

A. Connect a network cable to the new port(s).

B. Reconnect the two power cords on the back panel of the

HP NetStorage unit, and plug them into your power source.

C. urn on the unit.

. Press the alarm-reset button on the front panel to turn off

the alarm. he alarm sounds whenever the unit is powered on.

A. Follow one set of the directions below:

•If your system uses DHCP, the LCD panel will display the

IP address of the first NIC port. Move to Step 8.

•If your system does not use DHCP, use the LCD panel and

arrows to configure the IP address, Subnet mask, Broadcast

address, and Gateway address (if needed) for the newly installed

NIC. Move to Step 8.

NOTE: Only one Gateway address is supported, regardless of the

number of NIC ports installed.

Enter Network Information

A.

B.

.

A. Using a computer on the network, open a web browser and enter

the unit's IP address in the browser's address or location field.

B. Select Configuration > Network Settings.

C. ype in or verify the IP address and Subnet Mask for each new NIC

you installed.

. Click Apply.

Use a Web Browser to Enter Network Settings

All manuals and user guides at all-guides.com

*C4480-90101*

C4480-90101

All manuals and user guides at all-guides.com