HP StorageWorks 7110 - Virtual Array Bedienungsanleitung

VA Virtual Front Panel Commands

HP15 Firmware Release

April, 2002

Command Function

help Displays a description of each command.

setup Performs Virtual Front Panel configuration.

dsp Displays subsystem status.

cfg Performs subsystem configuration (LUN creation).

mgr Performs subsystem management operations.

fmt Performs an subsystem format.

rbld Performs rebuild operations.

recover Performs NVRAM recovery operations.

secure Performs security operations.

log Displays Logs

scsi Performs scsi command for provided cdb.

Usage Notes

To maintain consistency with earlier versions of the VFP, all commands can be prefaced with "vfp".

For help with a specific command, use the -? Option. For example, setup -?

For command recall, type “<” or “>”.

Command Options and Arguments Description

setup -e {on | off}

-r <value>

-c <value>

-b <int>

-e: Sets character echo

-r: Sets the number of rows:

<value>: range 5 – 1000

-c: Sets the number of columns:

<value>: ranger 40 - 8000

-b: Sets baud rate

<int> : 0, 1, 2, or 3

for 9600, 19200, 38400, 57600

Note: A firmware reset will restore the

default value of 9600.

dsp dsp (no argument follows)

-c [m/c1 | m/c2]

-d [fruLocation]

-L [LUN ID]

-s

-e

-f

Displays general information about the

subsystem.

-c: display controller information:

m/c1: controller 1, m/c2 controller 2

-d: display drive information:

[fruLocation] m/d#

-L: display LUN information (default for

all existing luns).

[LUN ID]: specify a requested LunID

-s: display subsystem settings

-e: enclosure information

-f: list of discovered FRUs

cfg cfg -L <LUN ID> -a <capacity> [{G|g}|{K|k}] –g <RG Id>

To Create a LUN requires three

parameters, LUN ID, capacity and RD

Id.

-L <LUN ID>: specify LUN ID to be

created.

-a <capacity>: specify LUN capacity.

Capacity is default to MB.

If followed by ‘K’ or ‘k’, the capacity is in

kilobytes and must be a multiple of

512.

If followed by ‘G’ or ‘g’, the capacity is in

gigabytes.

-g <RG ID>: redundancy group id. For

VA 7100 set to 1, for VA 7400 set to 1

or 2.

For valid number of LUNs to create,

check dsp –s for CREATE LUN LIMIT.

cfg -L <LUN ID> -d -L followed by –d: deletes LUN, no

need to specify capacity, just LUN ID.

mgr -s {shut | start}

-R {full | partial}

-L <loop id> -c {1|2}

-t {1 | 2 | 4} –c {1|2}

-S {1 | 2} –c {1 | 2}

-os {hpux | nt | win2k | linux | solaris | aix | netware |

generic | tru64 | openVMS | mpe | solarisCluster} –c {1 | 2}

-B {autoraid | raid1}

-O { on | off }

-q <queue full threshold>

-ds { on | off }

-p {on | off }

-V <Revision>

-s: Shutdown or restart the disk array

-R: Reset the disk array

-L: Set the FC Port Loop ID for the

Controller Port.

-t: Set the topology for the Controller

Port. Valid Arguments:

1- Private Topology

2 - Public Topology

4- Direct Fabric Attached Topology.

-S: Set the FC Port Speed for the

Controller Port.

Valid Arguments:

1- 1 GBit/sec Data Rate

2- 2 GBit/sec Data Rate

-c: Controller for which the port speed

will be set.

-os: Set Host behavior for controller

specified.

-c: Controller for which the host

behavior will be set.

-B: sets array RAID level (AutoRaid |

RAID 1).

-O: set enable optimize policy on/off.

-q: set queue full threshold ( 0 to 4096)

-ds: set disable secondary path

presentation

The -ds option determines whether the

array makes the non-optimal path to

LUNs visible to hosts. When set to ON,

secondary path presentation is enabled

and all LUNs are “visible” through all

ports on all controllers. When set to

OFF, each LUN will be “visible” only on

the controller that is the optimal

controller for that LUN. The optimal

controller is the one associated with the

redundancy group of which the LUN is a

part.

-p: Enable/disable prefetch.

-V: Set volume set revision. Valid

arguments:

1 – For HP01, HP02, HP11, HP13

2 – For HP14, HP15 and greater

fmt No options Perform array format (will destroy all

user data). User will be prompted with a

yes/no. The word ‘yes’ must be

entered completely. Otherwise the

format command will be canceled.

rbld -p

-a {on | off}

-p: Displays status/progress of a

subsystem rebuild.

-a: enables or disables autorebuild

recover No options

-s

Perform a recover process. Will ask for

user’s verification to proceed.

-s: returns the recoverability status or

the disk array, as well as the status of

the recovery progress.

secure -R

-e

-d

-R: Resets the password to AUTORAID.

-e: enables security.

-d: disables security.

log No options

-p <number of most recent events to display>

The log command ignores the row settings. If row setting

is less than 25, log command will set it to 25. In any case,

the row setting will be ignored when dispalying logs.

No options displays all events in buffer.

-p: display a given number of most

recent events.

scsi -cdb <cdblen> <cdb bytes…> <direction> [ -cdbcrc <cdb

crc>]

[ -lun <lunId> ]

[ -data <data len> <data bytes…> [ -datacrc <data crc> ] ]

direction can be: nodata | datain |

dataout

Documentation about this interface is

available upon request.

Andere Handbücher für StorageWorks 7110 - Virtual Array

Andere HP Lagerung Handbücher

HP LTO-4 HH Bedienungsanleitung

HP LTO-4 Ultrium 1760 Referenzhandbuch

HP Surestore 160ex - Optical Jukebox Bedienungsanleitung

HP R/T2200 G4 ERM Montageanleitung

HP StorageWorks 2/128 - SAN Director Switch Bedienungsanleitung

HP C7745NB - SureStore DLT Tape Autoloader 1/9 Bedienungsanleitung

HP AH164A - StorageWorks 1/8 G2 Tape Autoloader Ultrium... Bedienungsanleitung

HP StorageWorks 4000/6000/8000 - Enterprise Virtual... Bedienungsanleitung

HP StorageWorks 3800ux Bedienungsanleitung

HP StorageWorks 600 - Modular Disk System Merkblatt

HP StorageWorks XP48 - Disk Array Bedienungsanleitung

HP SmartMemory Bedienungsanleitung

HP 3PAR StoreServ 7200 2-node Bedienungsanleitung

HP FC 60 Handbuch

HP StorageWorks DLT 80 Gebrauchsanweisung

HP StorageWorks 500 Generation 2 Handbuch

HP StorageWorks 7100 - Virtual Array Technisches Dokument

HP D2D Bedienungsanleitung

HP ES3-H Series Montageanleitung

HP StorageWorks DAT 40m Bedienungsanleitung

HP AH164A - StorageWorks 1/8 G2 Tape Autoloader Ultrium... Bedienungsanleitung

HP Surestore Tape Library Model 2/28 Bedienungsanleitung

HP StorageWorks 7110 - Virtual Array Bedienungsanleitung

HP Surestore 160ex - Optical Jukebox Bedienungsanleitung

Beliebte Lagerung Handbücher anderer Marken

QNAP

QNAP TS 32PXU Series Bedienungsanleitung

LaCie

LaCie RUGGED RAID Bedienungsanleitung

Freecom

Freecom CLS DOCK Bedienungsanleitung

PNY

PNY Attache P-FD64MBATT3 Bedienungsanleitung

OLT

OLT 6x6 Maximizer Bedienungsanleitung

Transcend

Transcend JetFlash 160 Bedienungsanleitung

LaCie

LaCie RUGGED MINI Bedienungsanleitung

Thunderbolt

Thunderbolt 600 Bedienungsanleitung

Panasonic

Panasonic LB-DH8 series Handbuch

Intel

Intel RAID High Availability Bedienungsanleitung

LaCie

LaCie 12big Thunderbolt 3 Bedienungsanleitung

Spectra Logic

Spectra Logic T-Series Spectra T50e Bedienungsanleitung

Panasonic

Panasonic LKM-F931-1 Bedienungsanleitung

Tabernus

Tabernus Enterprise Erase E2400 Bedienungsanleitung

Rocstor

Rocstor COMMANDER 3F series Bedienungsanleitung

Western Digital

Western Digital Ultrastar Data60 Bedienungsanleitung

Dell

Dell PowerVault MD3600f Series Bedienungsanleitung

CFI

CFI TERA STOR SATA RAID IV Bedienungsanleitung