HP StorageWorks DLT VS 40/80 GB Bedienungsanleitung

hp StorageWorks

DLT VS 40/80 GB

internal tape drive

DLT VS 40/80 GB Internal Tape Drive Installation Instructions

Second Edition (January 2003)

Part Number: 289066-002

Hewlett-Packard Company makes no warranty of any kind with regard to

this material, including, but not limited to, the implied warranties of

merchantability and fitness for a particular purpose. Hewlett-Packard shall

not be liable for errors contained herein or for incidental or consequential

damages in connection with the furnishing, performance, or use of this

material.

This document contains proprietary information, which is protected by

or translated into another language without the prior written consent of

Hewlett-Packard. The information contained in this document is subject to

change without notice.

All other product names mentioned herein may be trademarks of their

respective companies.

Hewlett-Packard Company shall not be liable for technical or editorial

errors or omissions contained herein. The information is provided “as is”

without warranty of any kind and is subject to change without notice. The

warranties for Hewlett-Packard Company products are set forth in the

express limited warranty statements accompanying such products.

Nothing herein should be construed as constituting an additional

warranty.

installation

instruction

[bar code goes here in

text box, if applicable]

289066- 002

About this Document

This document provides instructions for installing the HP

StorageWorks DLT VS 40/80 GB Tape Drive into a server.

Required Tools

The following items may be required for DLT VS 40/80 GB

tape drive installation:

■Torx T-15 screwdriver

■Type 1A, Phillips screwdriver

Unpacking the Tape Drive

Caution: If the room in which you are unpacking the drive

differs from the temperature at which the tape drive was

shipped or stored by 30º F (15º C) or more, let the drive

acclimate to the surrounding environment for at least 12

hours before opening the shipping carton.

Unpack and inspect the tape drive for shipping damage:

1. Inspect the shipping box for damage. If you notice any

damage, report it to the shipping company immediately.

2. Open the shipping box and remove the accessories

package. Open the accessories package; you will need these

items during installation.

3. With the drive still in the shipping box, reach under and

around the drive. Carefully lift it out of the shipping box

and place it on the work surface, top facing up. Do not

stand the drive on either end.

4. Carefully remove the drive from the protective bag.

Note: Save the packing materials in case you need to move or ship

the drive in the future. You must ship the DLT VS 40/80 GB tape

drive in the original or equivalent packing materials to preserve

your warranty.

Page 2

Setting the SCSI ID

Each SCSI device attached to the server that is to be the host

for the DLT VS 40/80 GB tape drive must have a unique SCSI

ID. Check the SCSI IDs on all other devices attached to the

selected SCSI bus, including the SCSI host adapter itself, on

the selected server and select an unused SCSI ID for the tape

drive. If the drive factory default SCSI ID 6 is not being used

by another device on the same SCSI bus, you do not need to

change the SCSI ID.

Figure 1: Rear view of internal tape drive

168-pin SCSI connector

2Power connector

3SCSI ID jumpers

Note: If the tape drive is attached to a narrow SCSI bus, only IDs 0

through 7 are valid.

Locate the SCSI ID jumpers on the rear panel of the drive as

shown in Figure 1. Use Figure 2 to select the desired SCSI ID.

Figure 2: SCSI ID settings

Note: The SCSI ID can be set up to 15, but a SCSI ID above 6 is not

recommended.

Note: SCSI ID 7 is reserved for the controller.

Terminating the Tape Drive

If the DLT VS 40/80 GB tape drive is the only SCSI device –

other than the SCSI host adapter – on the selected server, it

must be terminated. Likewise, if the DLT VS 40/80 GB tape

drive is the last device on the selected server SCSI bus, it must

be terminated.

The DLT VS 40/80 GB tape drive ships with a ribbon cable

that is already terminated as shown in Figure 3. If you use a

cable other than the one provided, be sure that the cable is

terminated at each end.

Figure 3: Ribbon cable with terminator

Installing the Internal Tape Drive

Caution: Electrostatic discharge (ESD) can damage

electronic components. Be sure you are properly grounded

before beginning this procedure. Refer to Appendix B,

“Electrostatic Discharge,” in the

HP StorageWorks DLT VS

40/80 GB Tape Drive Reference Guide

for additional

information.

1. Shut down the operating system and power off the selected

server. Turn off all attached peripherals such as printers and

other SCSI devices. Remove the power cable from the host

server and all attached peripherals.

Caution: Failure to follow these instructions could result in

damage to the DLT VS 40/80 GB tape drive or other

devices.

2. Remove the cover from the host server to allow access to

the desired drive bay.

Note: Your server may differ from the following illustrations; refer to

the documentation included with your server.

1 2 3

SCSI ID 0 1 2 3 4 5 6

Jumper

Block

Page 3

Figure 4: Installing an internal drive

3. Install an LVD/SE SCSI host adapter in the server that is to

be the host for the drive, if necessary.

4. If necessary, attach the drive rails that ship with the drive.

Note: Your server may supply rails in the drive bay. Refer to your

server user guide for information on the correct rails to use with your

server.

5. Insert the drive into an available 5 1/4-inch drive bay.

Note: You may need to remove the front cover from the drive bay.

Refer to the documentation included with your server.

6. Secure the tape drive into the server according to the

documentation included with the server.

7. Connect an available power cable and the wide SCSI signal

cable.

Figure 5: Connecting the power and signal cable

1Signal cable

2Power cable

8. Attach the other end of the SCSI ribbon cable to the SCSI

host adapter.

9. Replace the cover on the server.

10. Plug in the AC power cords for any peripheral devices and

power all of them on.

11. Plug in the AC power cord for the server and power it on.

Verifying the Installation

Every time the DLT VS 40/80 GB tape drive is powered on, it

conducts a Power-On Self-Test (POST) to ensure that the drive

is working properly and ready to use.

While POST is in progress, watch the front panel LEDs to see

the progress and results of the test. During POST, the following

actions take place:

1. The LEDs turn on all at once and then turn off.

2. The Ready (green) LED remains illuminated after POST.

3. The drive emits a buzzing sound as the drive calibrates the

read/write head's position.

POST is complete only after the buzzing sound stops. POST

takes several seconds to complete, after which the drive is

ready to use. Refer to Chapter 5, “Operating the DLT VS 40/80

GB Tape Drive,” in the HP StorageWorks DLT VS 40/80 GB

Tape Drive Reference Guide.

Device drivers for Intel-based systems are located on the HP

website at:

http://wwss1pro.compaq.com/support/TSSD2/default.asp

Under Tape Drives, select VS80.

SELECT

ENTER

EJECT

Andere HP Lagerung Handbücher

HP StorageWorks 2012i Bedienungsanleitung

HP StorageWorks DAT 72 Bedienungsanleitung

HP 201723-B21 - HP StorageWorks Modular SAN Array 1000 Hard... Bedienungsanleitung

HP StorageWorks 1606 - Extension SAN Switch Bedienungsanleitung

HP StorageWorks XP12000 Bedienungsanleitung

HP 5243 Bedienungsanleitung

HP StorageWorks 4000/6000/8000 - Enterprise Virtual... Bedienungsanleitung

HP P10000 Bedienungsanleitung

HP StorageWorks 1/8 G2 Bedienungsanleitung

HP C1593B - SureStore DAT Tape 5000e Drive Bedienungsanleitung

HP HDD Bedienungsanleitung

HP Surestore 64 - Director Switch Bedienungsanleitung

HP STORAGEWORKS ALL-IN-ONE STORAGE SYSTEM Bedienungsanleitung

HP 624192-B21 Gebrauchsanweisung

HP Surestore 6164 - Switch Bedienungsanleitung

HP NetStorage 6000 Installations- und Betriebshandbuch

HP Surestore 160ex - Optical Jukebox Bedienungsanleitung

HP StorageWorks 1000 - Modular Smart Array Bedienungsanleitung

HP AJ765A - StorageWorks RDX Removable Disk Backup... Bedienungsanleitung

HP Surestore DLT 80 Bedienungsanleitung

HP StorageWorks 6100 - Enterprise Virtual Array Bedienungsanleitung

HP 330834-B21 - StorageWorks Ultrium 460 Tape Library Drive... Bedienungsanleitung

HP AH164A - StorageWorks 1/8 G2 Tape Autoloader Ultrium... Bedienungsanleitung

HP StorageWorks MSL6000 series Bedienungsanleitung

Beliebte Lagerung Handbücher anderer Marken

QNAP

QNAP TS 32PXU Series Bedienungsanleitung

LaCie

LaCie RUGGED RAID Bedienungsanleitung

Freecom

Freecom CLS DOCK Bedienungsanleitung

PNY

PNY Attache P-FD64MBATT3 Bedienungsanleitung

OLT

OLT 6x6 Maximizer Bedienungsanleitung

Transcend

Transcend JetFlash 160 Bedienungsanleitung

LaCie

LaCie RUGGED MINI Bedienungsanleitung

Thunderbolt

Thunderbolt 600 Bedienungsanleitung

Panasonic

Panasonic LB-DH8 series Handbuch

Intel

Intel RAID High Availability Bedienungsanleitung

LaCie

LaCie 12big Thunderbolt 3 Bedienungsanleitung

Spectra Logic

Spectra Logic T-Series Spectra T50e Bedienungsanleitung

Panasonic

Panasonic LKM-F931-1 Bedienungsanleitung

Tabernus

Tabernus Enterprise Erase E2400 Bedienungsanleitung

Rocstor

Rocstor COMMANDER 3F series Bedienungsanleitung

Western Digital

Western Digital Ultrastar Data60 Bedienungsanleitung

Dell

Dell PowerVault MD3600f Series Bedienungsanleitung

CFI

CFI TERA STOR SATA RAID IV Bedienungsanleitung