HP Surestore 160ex - Optical Jukebox Bedienungsanleitung

Adding 2 Drives to the

C1150 Series Jukebox

HP Part No. C1154-90001

Printed in USA June, 1996

Edition 1 0696

Important! Read This First

BEFORE starting this supgrade, obtain the following:

*The downloadable code required for this upgrade. FTP this code

* A PC with a SCSI interface and appropriate cables

from hpgrsg.gr.hp.com (15.38.89.10)using an "anonymous" login.

Further download instructions are available at that address.

* A utility to download the code - DOWNLD2 or HP TOOLSET (Version 1.95ce

This upgrade requires code to be downloaded to the controller PCA and the drives.

or later) from CoComp

Hewlett-Packard Company, 1996

Adding 2 Drives to the C1150 Series Jukebox

ESD Precautions

The optical disk jukebox contains very sensitive electrical components. It is EXTREMELY IMPOR-

TANT that you follow the proper procedures for preventing ESD (Electrostatic Discharge). Use wrist-

grounding straps, anti-static mats, and anti-static work stations when removing and replacing the

major assemblies.

Tools Required

The following tools are needed:

• Torx driver with the following bits: T-10, T-15, T-20

A T-20W bit may be helpful, but is not necessary.

a. For a performance upgrade, install 32 magazine slots (C1155F/G/H)

Before Upgrade... ... using this kit Upgraded to equivalent of:

(# of drives)

C1150F/G/H (2 drives) 1 kit (2 drives) C1160F/G/H (4 drives)a

Caution

Failure to follow proper procedures could lead to intermittent

failures and/or premature hard failures in the disk controller

and mechanism.

Kit Contents

• 2 - 4X MO drives — # C1113-60x00

• 2 - standard drive brackets — # C1170-60x47

• 2 - cable clamps — # 1400-0611

• 2 - drive SCSI cables — # C1173-60x59

• 2 - drive interface cables — # C1170-60x62

• 2 - drive power cables — # C1170-60x54

• 5 - threaded RLG screws — # 0515-2282

• 11 - M3x6 T10 screws — # 0515-2382

• 1 - these instructions

Note

The “x” in the part numbers listed in the following parts tables

represents a number from “0” to “9” depending on the

revision of the part. For example, if the part is newly

released, the number will be “0”. The ﬁrst time the part is

revised, the number increments to “1”; the second time the

part is revised, the number increments to“2”, and so on.

If you are unsure of the current part number, enter a “0” or a

“1” in place of the “x” when checking your parts database and

the current part number will be displayed.

Before You Begin

1. Look in the jukebox front "window" and make sure that there are no disks in any drive.

Use the control panel to eject any disk still in a drive

2. Bring the jukebox “down.”

Procedures for bringing this jukebox ofﬂine depend on the speciﬁc host system. Coordinate with

the system administrator to prepare this jukebox for the upgrade. This may involve “downing” the

host system also.

3. Remove power from the jukebox.

4. Disconnect the SCSI interface from the host.

Caution

Do NOT switch off power to the jukebox until you are sure the

SCSI bus is inactive. Switching off the jukebox when the

SCSI bus is active can cause data loss and/or indeterminate

bus states.

When doing this upgrade, be sure that disk cartridges are not

moved from their original slot locations. If you need to remove

the cartridges, record their SLOT LOCATIONS and

ORIENTATION so they can be replaced to their ORIGINAL

positions. Failure to follow this practice results in a serious

loss of ﬁle system integrity.

Installing the 2-Drive Upgrade

1. Remove the left, right and back panels. Refer to Figures 1 and 2.

Figure 1: Right-side panel access

a. Remove the T-20 screw that holds the bottom edge of the panel.

b. Lift panel up and out. (Internally, the panel rests on four retaining pins.)

c. Remove the left-side access panel by lifting it up and out. There is no screw on the bottom of

the left side panel.

Caution

Put on a grounding strap to work inside the outer shell of this

jukebox.

Figure 2: Rear access panel

d. Remove the 7 T-20 screws around the outer edge of the panel.

e. Remove the single screw underneath the bottom of the panel.

f. Rotate the back panel back and lift if off the frame.

arrows, screws

Rear, overall

Installing the 2-Drive Upgrade

1. Remove current drive cables from the interposer PCA.

2. Remove the air bafﬂe plate. Refer to Figure 3 for the correct location of the plate and of the 3

screws that must be removed. (You will need to use 2 of these screws to add the drive enclosures.).

Figure 3: Location of the air bafﬂe plate

3. Verify that DIP swtiches on the top of the new drives are set to OFF, which is in the forward posi-

tion (toward the front of the drive.) Refer to Figure 4.

Note

There is 1 drive installed in each drive enclosure.

To add 2 drives, you will install drive enclosures where the air

bafﬂe plate is currently installed.

Interposer PCA

Air

Bafﬂe

Plate

Drives

Figure 4: Ensuring drive DIP switches are all OFF

4. Install drives in drive enclosures (1 drive in each enclosure).

a. Remove the top cable access plate of each drive enclosure by removing the 2 T-10 screws which

hold the plate onto the enclosure.

b. Insert the drive interface, SCSI and power cables (in that order) through each drive enclosure

opening (from outside to inside, front to back in the opening). Refer to Figure 5 for proper

placement.

Figure 5: Cables positioned in the drive enclosure - ready for drive

Polaroid

c. Insert the single drive into the enclosure and position it near the cables at the rear, and in the

upper portion of the enclosure — do not mount the drive at this point — the drive interface

cable and clip must be mounted in the next step.

d. Connect the drive interface cable and clip.

Put the clip near the drive end of the cable. (Mounting the clip is shown separate from the drive

enclosure for clarity in Figure 6.)

Place the cable/drive connectors near each other. Remove the covering on the adhesive on the

back of the clip and press the clip into the position shown in Figure 7. Connect the drive inter-

face connector to the drive.

Figure 6: Clip placement on drive interface cable

Figure 7: Drive interface cable/cable clip positioning

Andere Handbücher für Surestore 160ex - Optical Jukebox

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere HP Lagerung Handbücher

HP StorageWorks SSL1016 Bedienungsanleitung

HP nimblestorage CS200 Series Bedienungsanleitung

HP P9000 Bedienungsanleitung

HP Rack Storage/12 Bedienungsanleitung

HP Surestore 64 - Director Switch Bedienungsanleitung

HP C2233 Bedienungsanleitung

HP StorageWorks 300 - Virtual Library System EVA... Bedienungsanleitung

HP AutoRAID 12H Kurzanleitung

HP AJ765A - StorageWorks RDX Removable Disk Backup... Bedienungsanleitung

HP StorageWorks 7110 - Virtual Array Kurzanleitung

HP Surestore 6164 - Switch Bedienungsanleitung

HP 9840 Bedienungsanleitung

HP DAT-160 Bedienungsanleitung

HP StorageWorks 1900ux Bedienungsanleitung

HP 9130K Bedienungsanleitung

HP StoreOnce D2D2500 Bedienungsanleitung

HP P2000 G3 Kurzanleitung

HP StorageWorks P2000 Bedienungsanleitung

HP StoreOnce B6000 Bedienungsanleitung

HP StorageWorks vs80 Bedienungsanleitung

HP Surestore 1200ex - Optical Jukebox Bedienungsanleitung

HP StorageWorks 1000 - Modular Smart Array Bedienungsanleitung

HP XP20000/XP24000 Bedienungsanleitung

HP Surestore Disk Array 12h - And FC60 Bedienungsanleitung

Beliebte Lagerung Handbücher anderer Marken

QNAP

QNAP TS 32PXU Series Bedienungsanleitung

LaCie

LaCie RUGGED RAID Bedienungsanleitung

Freecom

Freecom CLS DOCK Bedienungsanleitung

PNY

PNY Attache P-FD64MBATT3 Bedienungsanleitung

OLT

OLT 6x6 Maximizer Bedienungsanleitung

Transcend

Transcend JetFlash 160 Bedienungsanleitung

LaCie

LaCie RUGGED MINI Bedienungsanleitung

Thunderbolt

Thunderbolt 600 Bedienungsanleitung

Panasonic

Panasonic LB-DH8 series Handbuch

Intel

Intel RAID High Availability Bedienungsanleitung

LaCie

LaCie 12big Thunderbolt 3 Bedienungsanleitung

Spectra Logic

Spectra Logic T-Series Spectra T50e Bedienungsanleitung

Panasonic

Panasonic LKM-F931-1 Bedienungsanleitung

Tabernus

Tabernus Enterprise Erase E2400 Bedienungsanleitung

Rocstor

Rocstor COMMANDER 3F series Bedienungsanleitung

Western Digital

Western Digital Ultrastar Data60 Bedienungsanleitung

Dell

Dell PowerVault MD3600f Series Bedienungsanleitung

CFI

CFI TERA STOR SATA RAID IV Bedienungsanleitung