HP Xw4600 - Workstation - 2 GB RAM Bedienungsanleitung

SATA optical drive installation

This document describes how to install a standard 5.25-inch, half-height Serial ATA (SATA) optical drive

in your HP workstation.

Kit contents

●13.335 cm (5.25 inch), half-height SATA optical drive

●SATA interface cables

●Four M3 guide screws

●Optional application software CD (based on optical drive)

●Warranty information

Tools required

●T-15 Torx screwdriver

●Flat-blade screwdriver

Before you begin

To view QuickSpecs and determine the compatibility of this product with your HP workstation, see

http://www.hp.com/go/productbulletin.

Window XP and Windows Vista are U.S. registered trademarks of Microsoft

Corporation. Printed in the U.S.

ENWW Kit contents 1

Warnings and cautions

WARNING! Any surface or area of the equipment marked with this symbol indicates the presence

of an electrical shock hazard. To reduce the risk of injury from electrical shock, do not open any enclosed

area marked with this symbol.

WARNING! To reduce the risk of electric shock or damage to your equipment:

— Do not disable the power cord grounding plug. The grounding plug is an important safety feature.

— Plug the power cord in a grounded (earthed) outlet that is easily accessible at all times.

— Disconnect power from the equipment by unplugging the power cord from the electrical outlet.

WARNING! Any surface or area of the equipment marked with this symbol indicates the presence

of a hot surface or hot component. If this surface is contacted, the potential for injury exists. To reduce

the risk of injury from a hot component, enable the surface to cool before touching.

WARNING! If a product is shipped in packaging marked with this symbol, , the product must always

be lifted by two persons to avoid personal injury due to product weight.

WARNING! To reduce the risk of serious injury, read the Safety & Comfort Guide. It describes proper

workstation setup, posture, health, and work habits for computer users, and provides important electrical

and mechanical safety information. This guide is located at http://www.hp.com/ergo and on the

documentation CD (if one is included with the product).

CAUTION: Static electricity can damage the electronic components of the workstation. Before

beginning these procedures, be sure you discharge static electricity by briefly touching a grounded metal

object.

CAUTION: To prevent damage to the workstation, observe the following Electrostatic Discharge

(ESD) precautions while performing the system parts removal and replacement procedures:

— Work on a static-free mat.

— Wear a static strap to ensure that any accumulated electrostatic charge is discharged from your body

to the ground.

— Create a common ground for the equipment you are working on by connecting the static-free mat,

static strap, and peripheral units to that piece of equipment.

NOTE: HP accessories are for use in HP Workstation products. They have been extensively tested

for reliability and are manufactured to high quality standards.

2 SATA optical drive installation ENWW

Preparing for component installation

NOTE: Workstation models vary. All illustrations are examples only.

Accessing the internal components of the workstation

1. If you need help preparing the workstation for this installation, consult the removal and replacement

procedures in the service guide for your workstation at http://www.hp.com/support/

workstation_manuals.

NOTE: For the HP Workstation series, these procedures are also available in the User

Guide on the Documentation and Diagnostics CD that shipped with your workstation.

2. Power down the workstation, and then disconnect the power cord.

3. Power down all external devices, and then disconnect them from the workstation.

4. Remove the side access panel.

Removing components

1. If installing in an HP 800 Workstation, remove the airflow guide to enable access to the optical

bays.

2. If present, remove the card support to enable access to the system board connectors.

3. Remove the front bezel if applicable.

NOTE: The front bezel does not need to be removed on HP 600 and HP 800 Workstations.

Installing the drive

CAUTION: There might be drive length limitations for some drive bays in certain workstations. Ensure

that the optical device does not come in contact with the system board or crush diskette drive cables.

1. Select the highest available optical bay position on the workstation that fits the length of the optical

device being installed.

NOTE: The HP SATA Blu-ray Writer does not fit in all removable drive bays. It is longer than most

optical drives. Choose the optical bay for the Blu-ray drive which best fits your workstation

configuration.

2. Remove the filler tray or the flat bezel blank from the front bezel of the appropriate drive bay. The

bezel blank is the small panel that covers the drive bay opening when a drive is not installed in the

bay.

3. Remove the EMI filler (if one is installed). The EMI filter is a thin metal piece blocking the bay

opening that reduces electromagnetic emissions.

ENWW Preparing for component installation 3

4. If your optical drive requires guide screws, use the four M3 guide screws provided as part of the

installation kit. Install two M3 guide screws into each side of the drive using a T-15 Torx screwdriver.

NOTE: Some workstations, such as HP 600, 800, xw6600, xw8600, and xw9400

Workstations do not require guide screws.

5. Install the optical drive.

a. On some workstation models, you will need to lift the spring-loaded latch on the left side of

the optical drive cage while sliding the new drive in place.

b. Slide the optical drive completely into a drive bay so that the drive is secured

CAUTION: Failure to ensure that the optical drive has been properly secured may cause damage

to the drive when moving the workstation. For specific instructions on securing an optional drive,

see the service guide for your workstation at http://www.hp.com/support/workstation_manuals.

6. Connect the cables.

CAUTION: Connect the power cable before connecting the data cable to reduce the risk of

damage to the drive due to Electrostatic Discharge (ESD).

a. Connect the workstation optical power supply power cable to the drive.

b. Connect the SATA interface cable

between the drive and the next available SATA

connector on the workstation system board.

NOTE: To locate system board connectors, see the service label on the side access panel.

NOTE: Select an interface cable from the kit that best fits the configuration of your HP

workstation. Choose a cable with two straight connectors if possible. If you are using an

interface cable with a right angle connector, avoid interference with plug-in cards by attaching

the straight connector into the system board and the right angle connector into the device.

4 SATA optical drive installation ENWW

7. Reassemble the workstation.

a. Reinstall the front bezel, if applicable.

b. Reinstall the expansion card support, if applicable.

c. Reinstall the airflow guide, if applicable.

d. Reinstall the side access panel.

e. Reconnect power to the workstation and all external devices.

f. Restore power to the workstation and all external devices.

8. For information on operating your drive and enabling digital audio:

●For the HP Workstation series, see the User Guide for your workstation at

http://www.hp.com/support/workstation_manuals.

●For the HP xw Workstation series, see the Setup and Troubleshooting Guide for your

workstation at http://www.hp.com/support/workstation_manuals.

9. For configuration rules and assumptions when installing both SATA and PATA optical drives in the

same workstation see:

●For the HP xw Workstation series, see the Setup and Troubleshooting Guide for your

workstation at http://www.hp.com/support/workstation_manuals.

NOTE: HP xw4600 Workstations do not support PATA optical drives.

●HP Workstation series do not support PATA optical drives.

10. If an application software CD to enable features for your device was included with your kit, then

insert it and follow the on-screen directions to load the software.

11. At the time of component installation, look for device software, firmware and driver updates,

designated for your workstation model and operating system. Obtain updates from

http://www.hp.com/go/workstationsupport.

ENWW Installing the drive 5

Notice for Blu-ray optical drives

If you installed a Blu-ray optical drive, note the following:

Blu-ray movie playback

As Blu-ray is a new format containing new technologies, certain disc, digital connection, compatibility

and/or performance issues may arise, and do not constitute defects in the product. Flawless playback

on all systems is not guaranteed. In order for some Blu-ray titles to play, they may require a DVI or HDMI

digital connection and your display may require HDCP support. HD-DVD movies cannot be played on

this workstation.

Blu-ray movie playback compatibility and update

Playing back Blu-ray HDCP (High-bandwidth Digital Content Protection) content such as commercially

distributed Blu-ray HD movies requires a fully HDCP compliant path on your computer. The HDCP

technology checks compliance of each component in the path from the content on the Blu-ray disc all

the way to the display monitor, including but not limited to graphic cards and monitor adapters.

The HP 400, 600 and 800 Workstations have been designed with this in mind; nearly all

configurations with currently available HP Professional Displays are compliant. Older HP xw4600 and

xw9400 Workstation configurations may not have fully compliant paths based on the installed graphics

card and display monitor; HP recommends confirming separately that you have a fully compliant system

if commercial content playback is a requirement for your use. HDCP compatibility of your graphics card

and monitor can be determined by checking the QuickSpecs at http://www.hp.com/go/productbulletin.

For the best HDCP performance, HP recommends that you install the latest updates:

1. Blu-ray player firmware

2. Playback application patches

3. Graphics firmware and drivers

Updates are located on the support web site for your specific product at http://www.hp.com/support/

workstations.

Regulatory notices

This product has been tested and found to comply with the limits for a class B digital device of the FCC

Rules. Refer to the Safety and Regulatory Information guide on the documentation CD that came with

your workstation for additional regulatory information governing this product.

Japanese 日本語

This document is available in Japanese. See http://www.hp.com/support/workstation_manuals, then

select your workstation product and select Japanese from the drop down Manual Language menu.

このドキュメントは日本語版が用意されています。http://www.hp.com/support/workstation_manuals

にアクセスし、ご使用のワークステーション製品を選択し、Manual Language ドロップダウンメニ

ューから Japanese を選択してください。

6 SATA optical drive installation ENWW

Andere Handbücher für Xw4600 - Workstation - 2 GB RAM

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere HP Lagerung Handbücher

HP P9000 Bedienungsanleitung

HP Surestore Disk Array 12h - And FC60 Bedienungsanleitung

HP StorageWorks XP10000 - Disk Array Bedienungsanleitung

HP 1040 Programmierhandbuch

HP StorageWorks 4000/6000/8000 - Enterprise Virtual... Bedienungsanleitung

HP X510 Gebrauchsanweisung

HP StorageWorks X5000 Bedienungsanleitung

HP EVA P6000 Bedienungsanleitung

HP Surestore Disk Array 12h - And FC60 Bedienungs- und Wartungshandbuch

HP ProLiant DL100 G2 DPSS Bedienungsanleitung

HP STORAGEWORKS XP24000 Bedienungsanleitung

HP LTO Ultrium series Bedienungsanleitung

HP P9000 Bedienungsanleitung

HP 157770-001 - DAT Drive 20/40 Tape Bedienungsanleitung

HP 705 Workstation Bedienungsanleitung

HP LTO-4 FH Bedienungsanleitung

HP 345524-B21 Bedienungsanleitung

HP C4405A - Colorado 14GB Tape Drive Bedienungsanleitung

HP StorageWorks 1/8 Bedienungsanleitung

HP Surestore 160ex - Optical Jukebox Bedienungsanleitung

HP 7957A Bedienungsanleitung

HP FC 60 Handbuch

HP Storevirtual 4000 Bedienungsanleitung

Beliebte Lagerung Handbücher anderer Marken

QNAP

QNAP TS 32PXU Series Bedienungsanleitung

LaCie

LaCie RUGGED RAID Bedienungsanleitung

Freecom

Freecom CLS DOCK Bedienungsanleitung

PNY

PNY Attache P-FD64MBATT3 Bedienungsanleitung

OLT

OLT 6x6 Maximizer Bedienungsanleitung

Transcend

Transcend JetFlash 160 Bedienungsanleitung

LaCie

LaCie RUGGED MINI Bedienungsanleitung

Thunderbolt

Thunderbolt 600 Bedienungsanleitung

Panasonic

Panasonic LB-DH8 series Handbuch

Intel

Intel RAID High Availability Bedienungsanleitung

LaCie

LaCie 12big Thunderbolt 3 Bedienungsanleitung

Spectra Logic

Spectra Logic T-Series Spectra T50e Bedienungsanleitung

Panasonic

Panasonic LKM-F931-1 Bedienungsanleitung

Tabernus

Tabernus Enterprise Erase E2400 Bedienungsanleitung

Rocstor

Rocstor COMMANDER 3F series Bedienungsanleitung

Western Digital

Western Digital Ultrastar Data60 Bedienungsanleitung

Dell

Dell PowerVault MD3600f Series Bedienungsanleitung

CFI

CFI TERA STOR SATA RAID IV Bedienungsanleitung