HP V1810g Bedienungsanleitung

HP Switch Quick Setup Guide

For more detailed instructions and information, view or download the documentation for your switch at

www.hp.com/networking/support.

1. Unpack and check included parts:

•Switch

• Accessory kit

•Powercord

• Documentation kit

2. Prepare for installation.

To avoid personal injury or product damage, review the

“Safety Precautions” on page 3.

3. Power on and verify selftest by connecting

the power cord.

Note: The switch does not contain a power switch.

It is turned on by connecting the power cord.

Port LEDs

After selftest:

PowerLED=On

Fault LED = Off

4. Install the switch.

To attach the mounting brackets to the switch, use a #1

Phillips (cross-head) screwdriver and the included 8-mm

M4 screws.

To mount the switch to a wall or wood surface, use two

5/8-inch (15.875 mm) number 12 wood screws (not

included).

Rack Mounting

Table or Desktop

Wall Mounting

5. Configure for operation on your network (minimal configuration).

To change the factory-default settings:

1. Reconfigure a PC’s IP address and Subnet Mask so that it can communicate

with the switch. For example, on a PC running Windows XP:

a. Click Start > Connect to > Show all connections.

b. Select and right-click Local Area Connection, then click Properties.

c. Scroll and select Internet Protocol (TCP/IP), then click Properties.

Note: Be sure to record all your PC’s current IP settings to be able to

restore them later.

d. On the General tab, click Use the following IP address.

e. For IP address, enter an IP address in the same range as the switch’s

default IP address. For example, enter 192.168.2.12.

f. For Subnet mask, enter 255.255.255.0, then click OK.

g. Click Close (or OK) to close the Local Area Connection Properties screen.

2. Connect the PC directly to the switch using a standard Ethernet LAN cable.

3. Open your Web browser on the PC, and enter the factory-default address,

http://192.168.2.10, to access the switch’s Web interface.

4. Click Log on to log onto the switch (there is no default password).

5. Click Network Setup > Get Connected and configure IP network settings on

the switch for operation on your network.

Note: If you enable DHCP for automatic IP network configuration, the

switch must be connected to the same network as the DHCP server. After

automatic IP configuration, you must determine the IP address assigned to

the switch. To do this, you will need to access your DHCP server files, or

use LLDP (Link Layer Discovery Protocol) commands on a connected

device (such as another switch).

6. Click Maintenance > Save Configuration and save your settings to retain them

when the switch is rebooted.

You are done with preconfiguration. Disconect the LAN cable, and return your

PC to its original network settings for your network..

Factory-default settings:

Connect a PC to configure the switch:

Parameter Factory Default Setting

Password <blank>

IP address 192.168.2.10

Subnet mask 255.255.255.0

Default gateway not set

Connect to

any port

6. Connect network cables.

RJ-45

connector Fiber cable

connector

Optional transceiver

(not included)

Safety Precautions

To avoid personal injury or product damage when installing your switch, read the installation precautions and guidelines below.

Installation Precautions

Warnings

■The rack or cabinet should be adequately secured to prevent it from becoming unstable and/or falling

over.

■Devices installed in a rack or cabinet should be mounted as low as possible, with the heaviest devices at

the bottom and progressively lighter devices installed above.

■Do not wall mount any switch without checking for restrictions in the Installation and Getting Started

Guide

Cautions

■Ensure the power source circuits are properly grounded, then use the power cord supplied with the switch to connect

it to the power source.

■If your installation requires a different power cord than the one supplied with the switch and/or power supply, be

sure the cord is adequately sized for the switch’s current requirements. In addition, be sure to use a power cord

displaying the mark of the safety agency that defines the regulations for power cords in your country/region. The

mark is your assurance that the power cord can be used safely with the switch and power supply.

■When installing the switch, the AC outlet should be near the switch and should be easily accessible in case the switch

must be powered off.

■Ensure the switch does not overload the power circuits, wiring, and over-current protection. To determine the

possibility of overloading the supply circuits, add together the ampere ratings of all devices installed on the same

circuit as the switch and compare the total with the rating limit for the circuit. The maximum ampere ratings are

usually printed on the devices near the AC power connectors.

■Do not install the switch in an environment where the operating ambient temperature exceeds its specification.

■Ensure the air flow around the switch is not restricted. Leave at least 7.6 cm (3 inches) for cooling. For the air flow

direction, see the Installation and Getting Started Guide for your product, located on the HP Web site at

www.hp.com/networking/support.

For additional Safety and Regulatory information, refer to the Safety and Regulatory documentation included with your switch.

The information contained herein is subject to change without notice.

Printed in China

February 2011

5998-1309

*5998-1309*

Andere HP Schalten Handbücher

HP 12500 Series Bedienungsanleitung

HP AA-RWF3A-TE Bedienungsanleitung

HP StorageWorks 64 - SAN Director Switch Bedienungsanleitung

HP 316095-B21 - StorageWorks Edge Switch 2/24 Bedienungsanleitung

HP ProCurve Series Bedienungsanleitung

HP McDATA 4Gb SAN Switch Bedienungsanleitung

HP STORAGEWORKS ALL-IN-ONE STORAGE SYSTEM Bedienungsanleitung

HP 316095-B21 - StorageWorks Edge Switch 2/24 Bedienungsanleitung

HP ProCurve 6120G/XG Bedienungsanleitung

HP ProCurve 6208M-SX Bedienungsanleitung

HP aruba 6300M Betriebsanleitung

HP AA979A - StorageWorks SAN Switch 2/8V Bedienungsanleitung

HP 262586-B21 - IP Console Switch 3x1x16 KVM Bedienungsanleitung

HP AdvanceStack 100Base-T Hub-8TXE Installations- und Betriebsanleitung

HP H3C S9500 Kurzanleitung

HP Brocade 4Gb SAN Switch Bedienungsanleitung

HP HPE 4200 Series Bedienungsanleitung

HP StorageWorks T5518A Bedienungsanleitung

HP 5900 Installationshandbuch

HP 489183-B21 - InfiniBand DDR Switch Bedienungsanleitung

HP 5900 Installationshandbuch

HP 316095-B21 - StorageWorks Edge Switch 2/24 Bedienungsanleitung

HP ProCurve Switch 1800-24G Bedienungsanleitung

HP A5830 Series Bedienungsanleitung

Beliebte Schalten Handbücher anderer Marken

URC

URC Total Control MFS-8 Bedienungsanleitung

Azbil

Azbil HPQ-D11 Bedienungsanleitung

Sony

Sony DFS-900M Bedienungsanleitung

SICK

SICK i17S Bedienungsanleitung

F&F

F&F SZR-277 Bedienungsanleitung

Shure

Shure UAMS/BK Bedienungsanleitung

Dräger

Dräger X-zone Switch Off Bedienungsanleitung

Asco

Asco Joucomatic 349 Series Bedienungsanleitung

BT Mini Hub Bedienungsanleitung

D-Link

D-Link DES-1226G Bedienungsanleitung

Johnson Controls

Johnson Controls FS80-C Bedienungsanleitung

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Bedienungsanleitung

MicroNet

MicroNet SP1200A Bedienungsanleitung

Ruijie

Ruijie RG-PF2920 Series Installations- und Betriebsanleitung

Altinex

Altinex DA1914SX Bedienungsanleitung

MiLAN

MiLAN MIL-SM2401M Bedienungsanleitung

RJM

RJM MASTERMIND PBC/6X Bedienungsanleitung

Atlas

Atlas MMK-KVM8 Bedienungsanleitung

HP v1810g Bedienungsanleitung

Beliebte Schalten Handbücher anderer Marken