HP 500R Series Bedienungsanleitung

500R Series Remote Access Points | Installation Guide 1

500R Series Remote Access Points

Installation Guide

The Aruba 500R Series access points are dual-radio 802.11ax Wi-Fi 6 remote access points that provide

connectivity for both wired and wireless client devices.

Package Contents

The following materials are included with this product:

nAP-503R Access Point

nAC-to-DCPower Adapter with Country-Specific AC Power Plug

Hardware Overview

Figure 1 AP-503R Front View

1 System Status LED

2 Radio Status LED

2| Rev 02|May 2023

Figure 2 AP-503R Rear and Side View

1Primary DC Power Port (Circular)

2Alternate DC Power Port (USB-C)

3E0 Ethernet Port (Uplink)

4 E1 Ethernet Port (Downlink)

5 E2 Ethernet Port (Downlink)

6 USB Type-A Host Port

7 Kensington Lock Slot

Figure 3 AP-503R Bottom View

1 USB Micro-B Console Port (proprietary)

2 Reset Button

LEDs

The LEDs located on the front panel of the access point indicate the system and radio status of the access

point.

System Status LED

The system status LED indicates the system status of the access point.

Color/State Meaning

Off Access point powered off

Green - blinking 1Access point booting, not ready

Green - solid Access point ready, fully functional

Red System error condition - Immediate attention required

Table 1: System Status LED

Radio Status LED

The radio status LED indicates the radio status of the access point.

Color/State Meaning

Off Device powered off, or both radios disabled

Green- solid Both radios enabled in access mode

Green- blinking One radio enabled in access mode, the other disabled

Amber- solid Both radio enabled in monitor mode

Amber- blinking One radio enabled in monitor mode, the other disabled

Alternating green/amber 2One radio enabled in access mode, the other in monitor mode

Table 2: Radio Status LED

1. Blinking: one second on, one second off, 2 seconds cycle.

2. Alternating: one second each color, 2 seconds cycle.

LED Display Settings

The LEDs have three operating modes that can be selected in the system management software:

nNormal mode: default after power on. Refer to Table 1 and Table 2.

nOff mode: the LEDs are all off

nBlink mode: both LEDs blink green (synchronized)

Rev 02 | May 2023 | 3

4| Rev 02|May 2023

Pressing the reset button for less than 10 seconds during normal operation will toggle the LED mode

between “normal” (default after power on) and “off” mode.

Pressing the reset button for longer than 10 seconds may cause the accesspoint to reset and return to the factory

default state.

Primary DC Power Port (Circular)

This DCpower port is designed for use with the power adapter (part number R9D91A) included in the

package.

After inserting the L-shape DC connector of the power adapter into the DCpower port, rotate the

DCconnector by 90 degrees and route the power cord through the cable hook on the access point. See

Figure 4 and Figure 5.

Figure 4 Connecting Power Adapter to DC Power Port

Figure 5 Routing Power Cord through Cable Hook

Alternate DC Power Port (USB-C)

The USB-C port is designed to offer an alternate way to provide DCpower to the AP-503R access point by

using a compatible 5V/3A USB-C power adapter.

Ethernet Ports

The AP-503R access point has three Ethernet ports (E0 - E2), shown in Figure 2.

nThe E0 port is a 100/1000Base-T auto-sensing MDI/MDIX uplink port .

nThe E1 and E2 ports are 100/1000Base-T auto-sensing MDI/MDIX downlink ports.

Ethernet Port LEDs

Each of the E0-E2 ports has one LED located on the top left corner of the port, indicating the network

status or activity on the port. See Figure 2 and Table 2

LED Color/State Meaning

Left Off Meet one of the following conditions:

naccess point is powered off

nport is disabled

nno link established

Green - blinking Activity detected on the port

Green - solid Link established at optimum speed (1Gbps)

Amber - solid Link established at reduced speed (100Mbps)

Table 3: Ethernet Port LEDs

USB Type-A Host Port

The USB Type-A host port supports the Aruba MDM-USB-LTE modem, Aruba AP-USB-ZB IOT radio module

and other compatible peripherals. When active, this USB port can supply up to 5W/1A to a connected

device.

Reset Button

The reset button can be used to reset the access point to factory default settings or turn off/on the LED

display.

Use one of the following methods to reset the access point to factory default settings:

nTo reset during normal operation:

lHold the reset button for more than 10 seconds while the access point is running.

lRelease the reset button.

nTo reset during power up, hold the reset button while the access point is powering up.

The system status LED will flash again within 15 seconds indicating that the reset is completed. The access

point will now continue to boot with the factory default settings.

To toggle the system status LED between “normal” (default after power on) and “off” mode, during the

normal operation of the access point, shortly press the reset button for less than 10 seconds.

USB Micro-B Console Port (Proprietary)

To create a console connection to the access point, follow these steps:

1. Connect the console port on the access point to the serial port on the computer using the proprietary

Aruba AP-CBL-SERU cable or AP-MOD-SERU module, which need to be purchased separately.

2. Start the terminal emulation software on the computer and configure a new serial session with the

following settings:

nSpeed: 9600 bps

nData bits:8

Rev 02 | May 2023 | 5

6| Rev 02|May 2023

nStop bits: 1

nParity: None

nFlow control: None

3. Start the terminal emulation session.

4. Press Enter once. If the connection is sucessful, you are prompted to login.

For this console port pin-out details, refer to Figure 6.

Figure 6 Micro-B Console Port Pin-out

1: NC

2: RXD

3: TXD

4: GND

5: GND

If needed, the AP console driver can be found at the Aruba support portal.

Kensington Lock Slot

The AP-503R access point is equipped with a Kensington lock slot for additional physical security.

Access Point Installation

All Aruba access points should be professionally installed by a professional installer. The installer is responsible for

meeting applicable national and electrical codes. Failure to properly install this product may result in physical injury

and/or damage to property.

Tous les points d'accès Aruba doivent impérativement être installés par un professionnel agréé. Ce dernier doit

s'assurer que l'appareil est mis à la terre et que le circuit de mise à la terre est conforme aux codes électriques

nationaux en vigueur. Le fait de ne pas installer correctement ce produit peut entraîner des blessures corporelles et

/ ou des dommages matériels.

For indoor use only. The access point, power adapter, and all connected cables are not to be installed outdoors. This

stationary device is intended for stationary use in partly temperature controlled weather-protected environments

(class 3.2 per ETSI 300 019).

You can put the AP-503R access point on any flat surface such as a desktop.

Software

For instructions on choosing operating modes and initial software configuration, refer to the AP Software

Quick Start Guide.

Aruba access points are classified as radio transmission devices, and are subject to government regulations of the

host country. The network administrator(s) is/are responsible for ensuring that configuration and operation of this

equipment is in compliance with their country’s regulations. For a complete list of approved channels in your

country, refer to the Aruba Downloadable Regulatory Table at

https://www.arubanetworks.com/techdocs/DRT/content/home.htm.

Verifying Post-Installation Connectivity

The integrated LEDs on the access point can be used to verify that the access point is receiving power and

initializing successfully. See Table 1,Table 2 and Table 2.

nEthernet:

lE0/E1/E3 port:100/1000Base-T auto-sensing MDI/MDX wired RJ45 network connectivity port

nPower

l12V DC power interface, support powering through AC-to-DC power adapter

lMaximum power consumption:Refer to datasheet

Environmental

nOperating

lTemperature: 0°C to +40°C (+32°F to +104°F)

lHumidity: 5% to 95% non-condensing

nStorage

lTemperature: -25ºC to 55ºC (-13ºF to 131ºF)

lHumidity: 10% to 100% non-condensing

Regulatory Information

For the purpose of regulatory compliance certifications and identification, this product has been assigned

a unique regulatory model number (RMN). The regulatory model number can be found on the product

nameplate label, along with all required approval markings and information. When requesting compliance

information for this product, always refer to this regulatory model number. The regulatory model number

RMN is not the marketing name or model number of the product.

The following regulatory model numbers apply to the 500R Series

nAP-503R RMN:APINR503

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s author-

ity to operate this equipment.

Toute modification effectuée sur cet équipement sans l'autorisation expresse de la partie responsable de la con-

formité est susceptible d'annuler son droit d'utilisation.

Safety and Regulatory Compliance

FCC Statement:Improper termination of access points installed in the United States configured to non-US model con-

trollers will be in violation of the FCC grant of equipment authorization. Any such willful or intentional violation may

result in a requirement by the FCC for immediate termination of operation and may be subject to forfeiture (47 CFR

1.80).

RF Radiation Exposure Statement: This equipment complies with RF radiation exposure limits. This equipment

should be installed and operated with a minimum distance of 7.87 inches ( 20 cm) between the radiator and your body

for 2.4 GHz and 5 GHz operations. This transmitter must not be co-located or operating in conjunction with any other

antenna or transmitter.

Rev 02 | May 2023 | 7

8| Rev 02|May 2023

Déclaration e la concernant l’exposition aux rayonnements à fréquence radioélectrique: Cet appareil est conforme aux

limites d’exposition aux rayonnements FR établies par la FCC. Il doit être installé et utilisé à une distance minimale de

20 cm (7.87 pouces) entre le radiateur et votre corps, qu’il opère sur la bande 2,4 GHz ou 5GHz. Cet émetteur ne doit

pas être installé ou utilisé à proximité immédiate d’une autre antenne ni d’un autre transmetteur.

The device could automatically discontinue transmission in case of absence of information to transmit, or operational

failure. Note that this is not intended to prohibit transmission of control or signaling information or the use of repet-

itive codes where required by the technology.

Brazil

Este equipamento não tem direito à proteção contra interferência prejudicial e não pode causar inter-

ferência em sistemas devidamente autorizados.

O uso deste equipamento é restrito a ambientes fechados e proibido em plataformas petrolíferas, carros,

trens, embarcações e no interior de aeronaves abaixo de 3.048 m (10.000 pés).

Canada

This Class B digital apparatus meets all of the requirements of the Canadian Interference-Causing

Equipment Regulations.

This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Eco-

nomic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions:

(1) This device may not cause interference; and (2) This device must accept any interference, including inter-

ference that may cause undesired operation of the device.

Canada

Cet appareil numérique de classe B respecte toutes les exigences du Règlement sur le matériel brouilleur

du Canada.

Cet appareil contient des émetteurs / récepteurs exemptés de licence qui sont conformes aux RSS

exempts de licence d'Innovation, Sciences et Développement économique Canada. Son fonctionnement

est soumis aux deux conditions suivantes: (1) ce périphérique ne doit pas provoquer d’interférences, et (2)

ce périphérique doit accepter toute interférence, y compris les interférences susceptibles de provoquer un

dysfonctionnement.

EU and UK Regulatory Conformity

The Declaration of Conformity made under Radio Equipment Directive 2014/53/EU as well as the United

Kingdom's Radio Equipment Regulations 2017/UK is available for viewing below. Select the document that

corresponds to your device’s model number as it is indicated on the product label.

nEU&UK Declaration of Conformity

Compliance is only assured if the Aruba approved accessories as listed in the ordering guide are used.

https://www.arubanetworks.com.

Wireless Channel Restrictions

5150-5350MHz band is limited to indoor only in the following countries; Austria (AT), Belgium (BE), Bulgaria

(BG), Croatia (HR), Cyprus (CY), Czech Republic (CZ), Denmark (DK), Estonia (EE), Finland (FI), France (FR),

Germany (DE), Greece (GR), Hungary (HU), Iceland (IS), Ireland (IE), Italy (IT), Latvia (LV), Liechtenstein (LI),

Lithuania (LT), Luxembourg (LU), Malta (MT), Netherlands (NL), Norway (NO), Poland (PL), Portugal (PT),

Romania (RO), Slovakia (SK), Slovenia (SL), Spain (ES), Sweden (SE), Switzerland (CH), Turkey (TR), United

Kingdom (UK (NI)).

Radio Frequency Range MHz Max EIRP

Wi-Fi 2412-2472 20 dBm

5150-5250 23 dBm

5250-5350 23 dBm

5470-5725 30 dBm

5725-5850 14 dBm

Lower power radio LAN product operating in 2.4 GHz and 5 GHz bands. Please refer to the ArubaOS User

Guide/Instant User Guide for details on restrictions.

European Union and United Kingdom

This device is limited for indoor use. Use in trains with metal-coated windows (or similar structures made

of materials with comparable attenuation characteristic) and aircraft is permitted. Operations in the 6GHz

band are blocked by firmware for some countries pending adoption of spectrum. Refer to Aruba DRT

release notes for details.

Japan

Korean

México

La operación de este equipo está sujeta a las siguientes dos condiciones: (1) es posible que este equipo o

dispositivo no cause interferencia perjudicial y (2) este equipo o dispositivo debeaceptar cualquier

interferencia, incluyendo la que pueda causar su operación no deseada.

Rev 02 | May 2023 | 9

10 | Rev 02|May 2023

Нормативные требования Евhразийского Экономического Союза

Russia

HPE Russia: ООО "Хьюлетт Паккард Энтерпрайз" Российская Федерация, 125171,

г. Москва, Ленинградское шоссе, 16А, стр.3, Телефон: +7 499 403 4248 Факс: +7

499 403 4677

'HPE Kazakhstan': TOO «Хьюлетт-Паккард (К)», Республика Казахстан, 050040, г.

Алматы, Бостандыкский район, проспект Аль-Фараби, 77/7, Телефон/факс: + 7

727 355 35 50

Kazakhstan

ЖШС "Хьюлетт Паккард Энтерпрайз" Ресей Федерациясы, 125171, Мәскеу, Ленинград тас жолы, 16A

блок 3, Телефон: +7 499 403 4248 Факс: +7 499 403 4677

ЖШС «Хьюлетт-Паккард (К)», Қазақстан Республикасы, 050040, Алматы к., Бостандык ауданы, Әл-

Фараби даңғ ылы, 77/7, Телефон/факс: +7 (727) 355 35 50

Ukraine

Hereby, Hewlett Packard Enterprise Company declares that the radio equipment type [The Regulatory

Model Number [RMN] for this device can be found in the Regulatory Information section of this document]

is in compliance with Ukrainian Technical Regulation on Radio Equipment, approved by resolution of the

CABINET OF MINISTERS OF UKRAINE dated May 24, 2017, No. 355. The full text of the UA declaration of

conformity is available at the following internet address:

https://certificates.ext.hpe.com/public/certificates.html.

Х’ЮЛЕТТ ПАКАРД ЕНТЕРПРАЗ, 6280 АМЕРИКА ЦЕНТР Д-Р, САН-ХОСЕ, КАЛІФОРНІЯ 95002, США

Taiwan

第十二條

經型式認證合格之低功率射頻電機，非經許可，公司，商號或使用者均不得擅自變更頻率、加大功率或

變更原設計之特性及功能。

第十四條

低功率射頻電機之使用不得影響飛航安全及干擾合法通信；經發現有干擾現象時，應立即停用，並改善

至無干擾時方得繼續使用。

前項合法通信，指依電信法規定作業之無線電通信。低功率射頻電機須忍受合法通信或工業、科學及

醫療用電波輻射性電機設備之干擾。

1.應避免影響附近雷達系統之操作。

2.高增益指向性天線只得應用於固定式點對點系統

3.電磁波暴露量 MPE 標準值 1 mW/cm2,送測產品實測值為: 0.1249 mW/cm2

UKCA

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere HP Drahtloser Zugangspunkt Handbücher

HP ProCurve 420 Bedienungsanleitung

HP ProCurve 530 WW Montageanleitung

HP MSM313 Kurzanleitung

HP MSM430 Bedienungsanleitung

HP J9467A Bedienungsanleitung

HP ProCurve 530 NA (J8986A) Bedienungsanleitung

HP Aruba AP-374 Montageanleitung

HP MSM466-R Bedienungsanleitung

HP ProCurve Wireless Access Point 530 Bedienungsanleitung

HP aruba AP-375ATEX Series Benutzerhandbuch

HP ProCurve Radio Port 230 Bedienungsanleitung

HP Aruba AP-377 Montageanleitung

HP Aruba 570 Series Bedienungsanleitung

HP ProCurve 420 NA Montageanleitung

HP Aruba AP-577 Montageanleitung

HP MSM422 Bedienungsanleitung

HP MSM410 Bedienungsanleitung

HP MSM310 Anleitung zur Verwendung

HP V-M200 Betriebsanleitung

HP ProCurve RSVLC-0501 Bedienungsanleitung

HP MSM3xx Bedienungsanleitung

HP 527 Bedienungsanleitung

HP ProCurve MSM317 Kurzanleitung

HP E-MSM466-R Bedienungsanleitung

Beliebte Drahtloser Zugangspunkt Handbücher anderer Marken

D-Link

D-Link DWL-2100AP - AirPlus Xtreme G Bedienungsanleitung

Ubiquiti

Ubiquiti NanoStation NSM2 Bedienungsanleitung

Cisco

Cisco Aironet 1550 Series Bedienungsanleitung

Aruba

Aruba IAP-335 Bedienungsanleitung

Advantek Networks

Advantek Networks AWN-AP-54MR Bedienungsanleitung

IP-COM

IP-COM AP355 Bedienungsanleitung

Buffalo

Buffalo AirStation WLA-L11G Bedienungsanleitung

EnGenius

EnGenius EnStationACv2 Bedienungsanleitung

D-Link

D-Link DAP-3662 Bedienungsanleitung

Widelink

Widelink ezWave WAP-1100 Series Bedienungsanleitung

Edimax

Edimax CAP1200 Bedienungsanleitung

xG Technology

xG Technology xMax CN1300 Bedienungsanleitung

Ubiquiti

Ubiquiti LBE-5AC-Gen2 Bedienungsanleitung

Aruba

Aruba AP-203R Bedienungsanleitung

LuXout Shades

LuXout Shades LUXSHADE MOTION Bedienungsanleitung

CreatComm

CreatComm TB5F Bedienungsanleitung

SineDigital

SineDigital MW-1500AP(H) Bedienungsanleitung

TP-Link

TP-Link AP9650 V1 Bedienungsanleitung