HRT VSM-802B Bedienungsanleitung
8 x 2 Video Matrix Switch
With Serial Keypads and Long Cable Compensation
VSM-802B
Hall Research Technologies, Inc.
Order toll-free in the U.S. 800-959-6439
FREE technical support, Call 714-641-6607 or fax 714-641-6698
Mail order: Hall Research Technologies, 1163 Warner Ave., Tustin, CA 92780
Web site: www.hallresearch.com • E-mail: info@ hallresearch.com
CUSTOMER
SUPPORT
INFORMATION
UMA1007 Reb B
1
8x2 Video Matrix Switch
TRADEMARKS USED IN THIS MANUAL
Hall Research, HRT, and (logo) are trademarks of Hall
Research Technologies, Inc.
Apple and Macintosh are registered trademarks of Apple Computer, Inc.
IBM is a registered trademark of International Business Machines
Corporation.
SGI is a registered trademark of Silicon Graphics, Inc.
Sun and Sun Microsystems are registered trademarks of Sun Microsystems,
Inc. in the United States and other countries.
Any other trademarks mentioned in this manual are acknowledged to be the
property of the trademark owners.
8x2 Video Matrix Switch
2
FEDERAL COMMUNICATIONS COMMISSION
AND CANADIAN DEPARTMENT OF COMMUNICATIONS
RADIO FREQUENCY INTERFERENCE STATEMENTS
This equipment generates, uses, and can radiate radio frequency energy
and if not installed and used properly, that is, in strict accordance with
the manufacturer’s instructions, may cause interference to radio
communication. It has been tested and found to comply with the limits
for a Class A computing device in accordance with the specifications in
Subpart B of Part 15 of FCC rules, which are designed to provide
reasonable protection against such interference when the equipment is
operated in a commercial environment. Operation of this equipment in
a residential area is likely to cause interference, in which case the user
at their ownexpense will be required to take whatever measures may
be necessary to correct the interference.
Changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate
the equipment.
This digital apparatus does not exceed the Class A limits for radio
noise emission from digital apparatus set out in the Radio Interference
Regulation of the Canadian Department of Communications.
Le présent appareil numérique n’émet pas de bruits radioélectriques
dépassant les limites applicables aux appareils numériques de la classe
A prescrites dans le Règlement sur le brouillage radioélectrique publié
par le ministère des Communications du Canada.
3
8x2 Video Matrix Switch
Contents
1. Introduction ....................................................................................... 4
2. Installation and Configuration ........................................................... 5
3. Operation ........................................................................................... 8
3.1 The Switch’s LEDs...................................................................... 8
3.2 Switching with the Keypads ........................................................ 8
3.3 Blanking the Video Output and Keypad Self-Test ...................... 8
4. Troubleshooting................................................................................. 9
4.1 Problem Solving FAQ ................................................................. 9
4.2 Calling Hall Research Technologies.......................................... 10
4.3 Shipping and Packaging ............................................................ 10
5. Specifications................................................................................... 11
6. Addendum ....................................................................................... 12
6.1 Switching with or through a Serial Device................................ 12
6.2 Configuring for Dual-head Display Devices ............................. 13
6.3 Scan Mode ................................................................................. 14
6.4 Blanking the output ................................................................... 15
6.5 Programming the Scan Period for each output .......................... 15
8x2 Video Matrix Switch
4
1. Introduction
The Model VSM-802B 8 in x 2 out Video Matrix Switch is an ideal tool
for sharing and/or switching between the output of as many as eight video
sources (such as PCs), in order to display or capture that output at two
video destinations (such as monitors). Once you attach all your devices,
you can hook the Switch to the included keypads for full switching control.
The Switch’s features include:
•With its large bandwidth, it can handle even very high resolutions
and refresh rates, up to 1600 x 1280 pixels at up to 85 Hz.
•It includes two serial keypads, so it’s ready to do manual
switching almost right out of the box (you do have to attach the
keypad to the Switch first).
•Because it has a universal power supply, you can plug it in almost
anywhere if you have the right input cord. (And it’s small and
light enough to take almost anywhere!)
•It’s primarily designed to carry VGA/XGA video, but it can
handle separate horizontal and vertical sync, composite sync, and
sync on green, so with the right kinds of cables or adapters it can
accept all sorts of video from all sorts of devices.
•All of its input and output signals are buffered, so you’ll get the
sharpest possible images.
•It can drive video signals as far as 300 ft. (90 m) end-to-end, so
it’s ideal for use in auditoriums, conference halls, and similar
spaces.
•Its front-panel LEDs show you right away which video inputs are
going to which outputs.
•To top it off, it can be operated by pressing a single keypad
button, so anybody can use it without having to be extensively
trained.
The Switch comes with:
•(2) 10-button keypads
•(2) 6-ft. (1.8-m) DB9 male to DB9 female keypad cables
•Power supply
•This manual
5
8x2 Video Matrix Switch
2. Installation and Configuration
To set up your VSM-802B 8 x 2 Video Matrix Switch system, take these
steps:
Making sure that the Switch is powered off, find its input ports. (These are
the HD15 connectors on its front panel labeled “INPUT 1” through
“INPUT 8.”)
Run cabling from these ports to the video-output ports of the PC CPUs or
other devices that will be providing the Switch’s video input. If all of these
input devices are transmitting VGA/SVGA/XGA-type video signals on
HD15 female connectors, you can use standard VGA video extension
cables such as our product CVGX-xx-MM. Keep in mind that the length of
any of these cables plus the length of any of your monitor/output cables
(see step 2) should not be more than 300 ft. (90 m). You’ll configure the
Switch for the length of your cables in step 3.
If any of your input devices transmit some other type of video signal and/or
use some other type of video connector, you might need special cables or
adapters; call HRT Technical Support.
Figure 2-1. The Switch’s rear-panel components.
The Switch’s output ports are the two HD15 female connectors labeled
“OUT A” and “OUT B” on the Switch’s rear panel. If both of your output
devices are standard VGA or multisync monitors with HD15 male
connectors on their video cables, you can plug them directly into these
ports (if they’ll be placed nearby) or run video-extension cables to them
such as our product CVGX-xx-MF (if they’ll be some distance away).
Keep in mind that the length of any of these cables plus the length of any of
your CPU/input cables (see step 1) should not be more than 300 ft. (90 m).
(You’ll configure the Switch for the length of your cables in step 3.)
If either of your output devices is designed to receive a non-VGA video
signal and/or use a different type of video connector, you might need
special cables or adapters; call HRT Technical Support.
8x2 Video Matrix Switch
6
1. For each of the two outputs there is an 8-position DIP switch on
the Video Matrix Switch’s rear panel - labeled “GAIN A” for
“OUT A” and “GAIN B” for “OUT B” - that you can use to
control the gain applied to the corresponding input signals. For each
of the eight inputs, calculate the total lengths of the video cables from
the source to each of the two destinations (the devices attached to
OUT A and OUT B). Then set the corresponding switch position (“1”
for input 1 through “8” for input 8 on either GAIN A for OUT A or
GAIN B for OUT B): Move it DOWN if the total length is 100 ft. (30
m) or less, or UP if the total length is over 100 ft. (30 m). (In the UP
setting, extra compensation is added to the signal to make up for the
high-frequency losses typical of longer cabling.)
2. Run the included 6-ft. (1.8-m) DB9 cable from the two included
keypads to the DB9 female connectors labeled “KEYPAD A” and
“KEYPAD B” on the Switch’s rear panel. If you have either
monitor placed father than 6-ft. (1.8 m) from the Switch, you can
use DB9 male to DB9 female extension cable such as CDB9-xx-MF to
run just as far to the keypad, up to the maximum of 300 ft. ( 90 m ) .
3. Plug the output cord of the Switch’s power supply into the
Switch’s 5-pin DIN female power inlet. Plug one end of the power
supply’s input cord into the transformer’s IEC 320 male inlet; plug
the other end of the input cord into a working AC outlet. Your
Video Matrix Switch system is now fully installed, as shown in Figure
3-2 on the next page.
4. Now you can turn on all attached devices. The system should
power up in its last state, with each of the Switch’s outputs
displaying its last selected input. If it does, the system should be
ready for continuous operation. If it doesn’t, check the rear-panel
LEDs to make sure the Switch is ON; check your devices and make
sure they’re ON; and check the cabling and make sure it’s all properly
connected. If everything seems like it should work but the system still
doesn’t, call HRT Technical Support.
7
8x2 Video Matrix Switch
Figure 3-2. A fully installed Switch system.
High-Density 15-Pin VGA Connector
PIN Function
1 Red
2 Green
3 Blue
4 Not Used
5 Gnd
6 Red Return (Gnd)
7 Green Return (Gnd)
8 Blue Return (Gnd)
9 Key (Not Used)
10 Gnd
11 Gnd
12 SDA (plug-n-play)
13 Horizontal Sync
14 Vertical Sync
15 SCL (plug-n-play)
8x2 Video Matrix Switch
8
3. Operation
3.1 The Switch’s LEDs
The LEDs on the 8 x 2 Video Matrix Switch’s rear panel, shown in Figure
3-1 at the start of Chapter 2, indicate which of the Switch’s outputs are
displaying the video from which inputs, and which outputs have been
blanked and aren’t showing anything (see Section 3.3) .
There are two rows of eight LEDs, labeled “Channel” and “1” through “8.”
The top row shows which input is selected for “OUT A,” while the bottom
row shows which input is selected for “OUT B.” If no LEDs are lit in an
output port’s row, the output has been blanked and the keypad is in test
mode (see Section 3.3)
3.2 Switching with the Keypads
To switch your output port’s monitor or other destination device to display
a given input, press the number of that input on your keypad. For example,
to display the video from a CPU attached to INPUT 8, press the “8” button.
The LED next to that button will light (and will stay lit until a different port
is selected). Buttons 9 and 10 on the keypad have no switching function;
pressing them will have no effect unless you press both at the same time,
which will blank the output and trigger the keypad’s self-test function (see
Section 3.3).
3.3 Blanking the Video Output and Keypad Self-Test
Pressing both the 9 and 10 buttons simultaneously on one of the Switch’s
keypads will blank the video output controlled by that keypad (the monitor
will go dark). It will also cause that keypad to go into self-test mode and
light all of its LEDs. If you see that any of the LEDs don’t light while a
keypad is in this mode, consider contacting HRT to arrange for the keypad
to be repaired or returned. (A dark LED probably just means that the LED
is defective, but there’s a slim chance that something more serious might be
wrong.) To exit test mode and restore video output of the previously
selected channel, press any button (1 through 8).
Inhaltsverzeichnis
Andere HRT Matrix-Umschalter Handbücher
