Htek EHS30 Bedienungsanleitung

Notices Information

Htek EHS30 Adapter User Manual

Version 2.0.4.4.24

Feb. 2018

Notices Information

Nanjing Hanlong Technology Co., LTD. owns all the rights to modify and copy this

document at any time. And all the illustrations and text in this document are copyright

protected. Therefore, no parts of this document may be used or reproduced, transmitted

by the third parties for any purposes without the express written permission of Nanjing

Hanlong Technology CO., LTD.

When this document is made available on www.Htek.com , Nanjing Hanlong Technology

Co., LTD.gives its right to download and print copies of this content only for private use as

a user manual. No parts shall have the right to alter, modify or use as commercial means

without prior written permission from Nanjing Hanlong Technology Co., LTD.

Safety Instructions

To use the EHS30, please followthe instructions inthis user manual.

This EHS30 is only for indoor use. And also avoid in high humidity, water and some

other liquids.

Do not use the EHS30 during thunderstorms.

CE

FCC

WEEE Warning

To avoid the potential effects on the environment and human health as a

result of the presence of hazardous substances in electrical and electronic

equipment, end users of electrical and electronic equipment should

understand the meaning of the crossed-out wheeled bin symbol. Do not

dispose of WEEE as unsorted municipal waste and have to collect such

WEEE separately.

Cleaning

To clean the device, use an anti-static cloth. Please avoid cleaning liquids as they might

damage the surface or internal electronics of the EHS30.

Notices Information

FCC Statement

1. This device complies with Part 15 of the FCC Rules. Operation is subject to the

following two conditions:

(1) This device may not cause harmful interference.

(2) This device must accept any interference received, including interference that may

cause undesired operation.

2. Changes or modifications not expressly approved by the party responsible for

compliance could void the user's authorityto operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B

digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide

reasonable protectionagainst harmful interference in a residential installation.

This equipment generates uses and can radiate radio frequency energy and, if not

installed and used in accordance with the instructions, may cause harmful interference to

radio communications. However, there is no guarantee that interference will not occur in a

particular installation. If this equipment does cause harmful interference to radio or

television reception, which can be determined by turning the equipment off and on, the

user is encouraged to try to correct the interference by one or more of the following

measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

Consult the dealer or an experienced radio/TV technician for help.

Table of Content

Notices Information .........................................................................................................2

Copyright..................................................................................................................2

Safety Instructions....................................................................................................2

WEEE Warning ........................................................................................................2

Cleaning...................................................................................................................2

FCC Statement.........................................................................................................3

Table of Content..............................................................................................................4

Introduction.....................................................................................................................5

Description...............................................................................................................5

Compatibility.............................................................................................................5

Getting Started................................................................................................................6

EHS-30 Package Contents.......................................................................................6

EHS-30 Ports and LEDs Description........................................................................6

Installation for Plantronics Headsets.........................................................................7

Installation for Jabra Headsets.................................................................................7

Installation for SENNHEISER Headsets ...................................................................8

IP Phone Configuration (for all Wireless Headsets) .......................................................10

Headset Usage (for all Wireless Headsets)....................................................................11

Introduction

Description

The Htek™ EHS30 Wireless Headset Adapter is perfect for connecting Htek phones to

supported wireless headsets. It is simple to use and install, and allows the user to

control off-hook, talk, and on-hook modes of Htek (Hanlongtek) IP phones from the

headset. The EHS Adapter connects between the Htek IP phone and the Wireless

Headset base unit.

Compatibility

Htek IP Phones *: UC926, UC926E, UC924, UC924E, UC923, UC903, UC862, UC842,

UC860, UC840, UC806, UC806T, UC806G, UC804, UC804T and UC804G.

Plantronics® Wireless Headsets: Plantronics CS510, CS520, CS540. (Headset bases

C052 and C054)

Jabra® Headsets: 9400BS (9460), WHB005BS(U) (925), BT2046.

SENNHEISER® Wired headset: SC230,SC260,SC660

SENNHEISER® Wireless Headsets: DW Pro2,SD Pro2,D10

*Firmware Note: Plantronics Headsets require Htek firmware 1.0.3.88 (2015_08_21) or

later, and Jabra Headsets require Htek firmware 1.0.3.94 or later.

Getting Started

EHS-30 Package Contents

EHS-30 Ports and LEDs Description

(1) RJ-12 Port for IP Phone EXT/EHS or Expansion Module

(2) Operation LED

(3) 3.5mm DC Power Jack (for Plantronics Headsets)

(4) RJ-45 Jack (for Jabra Headsets)

Getting Started

Installation for Plantronics Headsets

The following figure shows the connections between the EHS-30 Adapter, the bottom of

the Htek IP Phone, and the Plantronics wireless headset base unit.

Steps:

1. Connect the Wireless Headset to the RJ-9 Headset port on the IP Phone, using the

cord provided by Plantronics.

2. Connect the included RJ-12 cord between the EHS-30 Adapter RJ12 Port (Port 1) and

the EXT/EHS port of the Htek IP Phone (or to the Expansion Module EXT port, if the

expansion module is connected).

3. Connect the 3.5mm DC Power Port (Port 3) of the EHS-30 Adapter to the Plantronics

Wireless headset using the included 3.5mm DC power cord.

Note: For Plantronics Headsets, the RJ45 jack of the EHS-30 Adapter is not used.

Installation for Jabra Headsets

The following figure shows the connections between the EHS-30 Adapter, the bottom of

the Htek IP Phone, and the Jabra wireless headset base unit.

Getting Started

Steps:

1. Connect Aux Port of the Jabra Wireless Headset to the RJ45 port (Port 4) of the

EHS-30Adapter. (The RJ-45 cord may be supplied by Jabra or obtained separately).

2. Connect the included RJ-12 cord between the EHS-30 Adapter RJ12 Port (Port 1) and

the EXT/EHS port of the Htek IP Phone (or to the Expansion Module EXT port, if the

expansion module is connected).

3. Connect the RJ-9 cord from the Jabra Wireless Headset to the Headset jack of the Htek

IP phone.

Note: For Jabra Headsets, the 3.5mm DC Power jack and cord are not used.

Installation for SENNHEISER Headsets

The following figure shows the connections between the EHS-30 Adapter, the bottom of

the Htek IP Phone, and the SENNHEISER wireless headset base unit.

Steps:

1. Connect EHS Port of the SENNHEISER Wireless Headset to the RJ45 port (Port 4) of

the EHS-30 Adapter. (The RJ-45 cord may be supplied by SENNHEISER or obtained

Getting Started

separately).

2. Connect the included RJ-12 cord between the EHS-30 Adapter RJ12 Port (Port 1) and

the EXT/EHS port of the Htek IP Phone (or to the Expansion Module EXT port, if the

expansion module is connected).

3. Connect Telephone Port of the SENNHEISER Wireless Headset to the Headset jack of

the Htek IP phone.

Note: For SENNHEISER Headsets, the 3.5mm DC Power jack and RJ45 jack are not

used.

IP Phone Configuration (for all Wireless Headsets)

IP Phone Configuration (for all Wireless

Headsets)

For Wireless Headset operation, set the following parameters using the IP Phone Web

GUI interface:

1. Log in to the Web Configuration GUI for the IP Phone (as described in the User

Manual).

2. Go to Setting -> Preference

3. Set “HeadSet Priority” to “Enable”

4. Set “Ringer Device For HeadSet” to “Use HeadSet”

Refer to the picture below for the correct settings:

Andere Handbücher für EHS30

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Htek Adapter Handbücher

Htek

Htek EHS30 Bedienungsanleitung

Beliebte Adapter Handbücher anderer Marken

PCB Piezotronics

PCB Piezotronics 090B274 Bedienungsanleitung

Auvidea

Auvidea J20 Produkthandbuch

Gossen MetraWatt

Gossen MetraWatt AT3-III E Bedienungsanleitung

Akribis

Akribis ITF-21-BISS-MIT Bedienungsanleitung

Tenda

Tenda W54U Bedienungsanleitung

ROHO

ROHO AGILITY Bedienungsanleitung

PROLiNK

PROLiNK WN2001 Bedienungsanleitung

Hawking

Hawking HUF2 Bedienungsanleitung

Airlink101

Airlink101 AWLC4030 Bedienungsanleitung

NETGEAR

NETGEAR XAV101v1 - Powerline AV Ethernet Adapter Bedienungsanleitung

Philips

Philips SWA4554S/10 Bedienungsanleitung

JVC

JVC TS-C9D2B Gebrauchsanweisung

NETGEAR

NETGEAR A6100 Bedienungsanleitung

D-Link

D-Link DWA-121 Bedienungsanleitung

Philips

Philips SWA2037 Bedienungsanleitung

Basalte

Basalte 0610-20 Bedienungsanleitung

Yealink

Yealink EHS40 Bedienungsanleitung

Balluff

Balluff BIC 1B0-IT1A7-Q40KFU-SM4A4A Bedienungsanleitung