Huawei SmartLogger2000-10-C-JP Bedienungsanleitung

HUAWEI TECHNOLOGIES CO., LTD.

SmartLogger2000-10-C-JP

Quick Guide (Japan)

Issue: 03

Part number: 31509082

Date: 2019-06-30

1Overview

1. The information in this document is subject to change without notice. Every effort has been made

in the preparation of this document to ensure accuracy of the contents. However, all statements,

information, and recommendations in this document do not constitute a warranty of any kind,

express or implied.

2. Before installing the device, carefully read the SmartLogger2000 User Manual to get familiar with

the product information and precautions. SmartLogger is short for SmartLogger2000-10-C-JP in

the following text.

3. Install and use the device according to this document and the user manual. Otherwise, the device

may be damaged. Use insulated tools when installing the device.

4. When the SmartLogger is applied in a non-Huawei smart array controller (smart array controller

for short), install it in the third-p arty cabinet. This section describes the installation and cable

connection operations using the SmartLogger in non-Huawei smart array controller scenario as

an example.

Model Description

1.1

Model

Description

SmartLogger2000

-10-C-

10-C: with a built-

in 800 V AC PLC (MBUS) central coordinator (CCO)

JP: target market

The built-in Bluetooth module supports both Android APP and iOS APP.

NOTE

Port Description

1.2

No.

Port (Silk Screen)

Function Description

RF1, RF2

Reserved

Reserved.

12V OUT

12 V DC output

Provides 12 V DC power supply with a maximum

current of 100 mA.

12V IN

12 V DC input

Connects to the power adapter.

USB

USB port

Connects a USB flash drive.

SFP1, SFP2

Ethernet optical port

Connects to an ATB or another cascaded

SmartLogger.

ETH1, ETH2

Ethernet electrical

port

Connects to an Ethernet LAN switch, router or

PC device.

Digital output (DO)

Relay output supports 12 V voltage and 0.5 A current.

COM1

–COM6

RS485

communications

Six RS485 ports that can be connected to devices

such as

the inverter, cubicle, power meter, or EMI.

No.

Port (Silk Screen)

Function Description

Default

Default key

Resets and restarts the Bluetooth module or resets

the SmartLogger IP address to the default IP address

(valid within 5 minutes). The default IP address is

192.168.0.10.

AC1, AC2

AC power cable

ports

Connects to

three-phase (U, V, and W) inputs

, and is

used for PLC (MBUS) with the SUN2000 over AC

power cables.

If PLC (MBUS) function is not used,

you do not have to connect cables to these ports.

Shell

ground point

N/A

AI1

–AI7

Analog input

AI1 supports 0

–10 V input voltage (passivea); AI2–

AI7 support 0

–20 mA and 4–20 mA input current

(passive).

PT1, PT2

Analog input



PT1 supports the connection to a three-wire or two

wire PT100/PT1000 temperature sensor.



PT2 supports the connection to only a two-wire

PT100/PT1000 temperature sensor.

AO1

–AO4

Analog output (AO)

–20 mA and 0–20 mA output current

DI1

–DI8

Digital input (DI)

Connects to a dry contact input. GND1 and GND2

are ground ports for DI signals.

Note a: Passive means that the AI port can connect to a sensor that needs to be energized separately.

2Typical Cable Connection Scenarios

Non-Smart Array Controller Scenario

2.1

1. The SmartLogger can connect to an inverter over an RS485 communications cable.

2. The power cable delivered with the SmartLogger is 1 meter long, the power adapter cable is 1.5

meters long, the network cable is 2.2 meters long, and the AC power cable is 1.5 meters long.

Reserve the installation positions for components based on the cable lengths.

3. The tables under figures list only the components to be configured by the customer in the

corresponding scenario.

Optical Fiber

Component Recommended Model or Specifications Component

Source Quantity

SmartLogger SmartLogger2000 Can be

purchased

from Huawei 1

Fitting

bag for

fiber ring

switching

Low-speed

optical

module FTLF1323P1BTR-HW Can be

purchased

from Huawei

Optical

jumper PLCLC5S-ST3P302-HW, LC-LC-S2-L2,

3ECA1031LCLC002-01-F, or LP-LP-2S-P-SM-002 8

ATB CT-GZF2PJ-8, CT-GPH-A-8, or an ATB of a local

model Prepared by

the customer 1

Socket Connects to the power adapter. Prepared by

the customer 1

Smart Array Controller Scenario

2.2

This document describes the application scenario where the SmartLogger is inside the smart

array controller SmartACU2000B-D-2PID/2PLC.

The tables under figures list only the components to be configured by the customer in the

corresponding scenario.

NOTE

1. Prepare the single-phase AC power cable for the smart array controller by yourself. Recommended:

a two-core outdoor armor copper cable with an operating voltage to the ground greater than or equal

to 300 V and a cross-sectional area of 5.5 mm2for each core wire

2. The cable from the molded case circuit breaker (MCCB) to the station-service power source is

prepared by the customer. Recommended: a two-core outdoor armor copper cable with an operating

voltage to the ground greater than or equal to 300 V and a cross-sectional area of 5.5 mm2for each

core wire

3. Prepare the three-phase AC power cable for the smart array controller by yourself. Recommended: a

four-core (U, V, W, and functional earthing) outdoor armor copper cable with a cross-sectional area

of 8 mm2for each core wire. When the rated AC voltage on the low-voltage side of the cubicle is less

than or equal to 500 V, the operating voltage between the three-phase AC power cable and the

ground should be greater than or equal to 600 V.

4. The cable from the busbar to the 3P3E switch is prepared by the customer. Recommended: a four-

core (U, V, W, and functional earthing) outdoor armor copper cable with a cross-sectional area of 8

mm2for each core wire. When the rated AC voltage on the low-voltage side of the cubicle is less

than or equal to 500 V, the operating voltage to the ground should be greater than or equal to 600 V.

Optical Fiber

PLC

(MBUS)

CCO

Location Component Recommended Model or

Specifications Component

Source Quantity

Smart array

controller

LAN switch (optional) UT-H605 or ES1000 Can be

purchased

from Huawei 1

Fitting bag

for optical

ring

switching

Low-

speed

optical

module

FTLF1323P1BTR-HW Can be

purchased

from Huawei

Optical

jumper

PLCLC5S-ST3P302-HW, LC-

LC-S2-L2,

3ECA1031LCLC002-01-F, or

LP-LP-2S-P-SM-002

Cubicle

MCCB Rated current: 30 A, number

of poles: 2 Prepared by

the customer 1

3P3E switch

When the rated AC voltage

on the low-voltage side of

the cubicle is less than or

equal to 500 V, the rated

insulation voltage should

be 600 V.

The number of poles is 3.

When the rated AC voltage

on the low-voltage side of

the box-type transformer is

less than or equal to 500 V,

the rated current should be

30 A.

Prepared by

the customer

Scenario with a

double-column

transformer: 1

Scenario with a

dual-split

transformer: 2

Installation clearances

Guide rail-mounting

Chassis dimensions

(including the guide rail mounting brackets)

Installation Space (Unit: mm)

3.1

3Installing the SmartLogger

Chassis dimensions (including mounting ears) Installation clearances

Wall-mounting

Installation Mode

3.2

Wall-mounting

Install the SmartLogger on a wall that is flat and has the bearing capacity to securely hold the

SmartLogger.

Screw assembly for wall-mounting:

(1) ST3.5 tapping screw

(2) Washer

(3) Expansion sleeve

2. Drill holes by using a hammer drill and install expansion sleeves, washers, and tapping screws.

3. Put the tapping screws through the SmartLogger mounting ears and washers into the mounting

holes in the wall.

Unit: mm

1. Determine mounting holes based on the hole positions in the mounting ears, and mark

the mounting holes using a marker.

If you need to use a ladder to

install the device on a high

position, take measures to protect

yourself from falling down.

Unit: mm

4. Tighten the tapping screws using a torque screwdriver.

1. Remove the mounting ears from the

SmartLogger using a Phillips screwdriver. 2. Secure the guide rail clamps using the screws

that are removed from the mounting ears.

Guide rail-mounting

Huawei does not provide the SmartLogger guide rail. If the customer chooses this installation mode,

the customer must prepare a 35 mm standard guide rail.

Unit: mm

1. Secure the guide rail before mounting the

SmartLogger.

2. Verify that the length of the guide rail is

sufficient for securing the SmartLogger. The

recommended length is 450 mm or greater.

NOTE

3. Mount the SmartLogger onto the guide rail. 4. Install guide rail fasteners.

4Installing Ground Cable

Installing the SmartLogger Ground Cable

4.1

1. It is recommended that 4–6 mm2or 12–10 AWG outdoor copper-core cables be used as ground

cables. Ground cables must be securely connected.

2. To enhance the corrosion resistance of the ground terminal, apply silica gel or paint on it after

connecting the PGND cable.

OT-M6

NOTE

5Connecting Cables to COM Ports

The SmartLogger can connect to a inverter, an EMI, a power meter, a cubicle, and a PID module

through its COM ports.

NOTE

Port Definitions

5.1

For the definitions of the communications ports on the devices such as the EMI, power meter, and

cubicle, see the documents delivered with the devices. When connecting cables, ensure that

RS485+ connects to the COM+ port on the SmartLogger and that RS485–connects to the COM–

port on the SmartLogger.

For ease of operation, this document describes only the ports that need to be wired.

NOTE

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Huawei Steuereinheit Handbücher

Huawei

Huawei MU509-65 Montageanleitung

Huawei

Huawei ICD OPS D Series Bedienungsanleitung

Huawei

Huawei EM770 Bedienungsanleitung

Huawei

Huawei MU509 Series Bedienungsanleitung

Huawei

Huawei ME906E Bedienungsanleitung

Huawei

Huawei MU709Gs-8 Bedienungsanleitung

Huawei

Huawei PDU8000 Series Bedienungsanleitung

Huawei

Huawei ME909u-523 Montageanleitung

Huawei

Huawei UPS5000-E-400K-SMS Bedienungsanleitung

Huawei

Huawei EM820W Montageanleitung

Huawei

Huawei PDC V2.0 Bedienungsanleitung

Huawei

Huawei EM775 Bedienungsanleitung

Huawei

Huawei EM770U Bedienungsanleitung

Huawei

Huawei Atool Bedienungsanleitung

Huawei

Huawei MU609 Benutzerhandbuch

Huawei

Huawei SmartLi-ESM-24020P1 Bedienungsanleitung

Huawei

Huawei V100R001C00 Bedienungsanleitung

Huawei

Huawei MG323 Bedienungsanleitung

Huawei

Huawei RTN 380H Bedienungsanleitung

Huawei

Huawei UPS5000-E Series Bedienungsanleitung

Huawei

Huawei MU739 Montageanleitung

Huawei

Huawei ME936 Montageanleitung

Huawei

Huawei UPS5000-H-400K-NT Bedienungsanleitung

Huawei

Huawei MG323 Montageanleitung

Beliebte Steuereinheit Handbücher anderer Marken

Festo

Festo Compact Performance CP-FB6-E Stücklistenhandbuch

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung

JS Automation

JS Automation MPC3034A Bedienungsanleitung

JAUDT

JAUDT SW GII 6406 Series Kurzanleitung

Spektrum

Spektrum Air Module System Bedienungsanleitung

BOC Edwards

BOC Edwards Q Series Bedienungsanleitung

KHADAS

KHADAS BT Magic Bedienungsanleitung

Etherma

Etherma eNEXHO-IL Bedienungsanleitung

PMFoundations

PMFoundations Attenuverter Bedienungsanleitung

GEA

GEA VARIVENT Bedienungsanleitung

Walther Systemtechnik

Walther Systemtechnik VMS-05 Bedienungsanleitung

Altronix

Altronix LINQ8PD Montageanleitung

Eaton

Eaton Powerware Series Bedienungsanleitung

WAGO

WAGO 750-407/040-000 Bedienungsanleitung

Sony

Sony CCU-590 Bedienungsanleitung

Graco

Graco 25D614 Bedienungsanleitung

Task Force Tips

Task Force Tips YE-RF-900 Programmierhandbuch

Shini

Shini SPV-U Series Bedienungsanleitung