Huawei UPS5000-A-800 Series Bedienungsanleitung

Issue: 04

Part Number: 31508416

Date: 2019-03-02

UPS5000-A-800 kVA Quick Guide

1Overview

Model UPS5000-A-800K-F800-SC UPS5000-A-800K-F800-FC

Configuration Standard configuration Full configuration

Weight 1530 kg 1610 kg

Dimensions (H x W x D) 2000 mm x 2400 mm x 850 mm

(1) Power unit

(2) Control unit

(3) Mains input switch (only available

in the full configuration model)

(4) Maintenance bypass switch

(5) Output switch (only available in the

full configuration model)

(6) Bypass unit

(7) Bypass input switch (only available

in the full configuration model)

Power

cabinet Bypass

cabinet

Power

cabinet Bypass

cabinet

1. Before installation, read the user manual carefully to get familiar with product information and

safety precautions.

2. Use insulated tools during installation.

3. Only engineers certified by Huawei or its agents are allowed to install, commission, and

maintain the UPS. Otherwise, personal injury or equipment damage may occur, and the UPS

faults caused are beyond the warranty scope of Huawei.

Install on the steel channel or floor. Determine the mounting hole positions (unit: mm) using a marking-

off template, drill holes, and install expansion sleeves based on site requirements.

A: mounting holes on the steel channel B: mounting holes on the floor

2Installing the UPS

Determining Installation Position

2.1

Combining Power Cabinets and Bypass Cabinets

2.2

1. Combine in the following sequence: bottom, top, and middle.

(A) Mounting holes on the steel

channel: M12x60 bolts

(B) Mounting holes on the floor:

M12x100 expansion bolts

2. Secure the UPS.

4. Remove the front cover and No. 10 protection panel from the bypass cabinet and the filler panel

from the power cabinet.

3. Install anchor baffle plates.

Bolts are not

included.

NOTE

5. Cut off the cable ties bound between holes of copper bars No. 23, 24, 25, 26, and 30. Install

soft copper bars in the bypass cabinet and its adjacent power cabinet from inside out. Then,

install soft copper bars No. 52.

6. Reinstall the removed No. 10 protection panel on the bypass cabinet and the filler panel on

the power cabinet.

3Connecting Cables

1. This document describes cable routing by removing the top cover when there are two mains

inputs.

2. In the case of single mains, you do not need to connect bypass input power cables and

remove short-circuit copper bars.

UPS Cable Connection Reference

•Prepare cables away from the cabinets to prevent scraps from falling inside. Cable scraps may

ignite and cause personal injury or device damage.

•After cables have been installed, clean the cabinets in a timely manner. Keep the cabinets and

surrounding environment clean and tidy.

•You need to prepare terminals onsite. The stripped length of the copper wire should be the

same as that of the part of the terminal that covers the conductor.

3.1

The cabling route is for reference only. Connect cables based on site requirements.

NOTE

A UPS in standard configuration has only one switch cable (maintenance bypass switch). A

UPS in full configuration has three switch cables (mains input switch, maintenance bypass

switch, and bypass input switch). The following figure shows how to connect cables to a UPS in

full configuration.

Connecting Signal Cables to Combined Cabinets

3.2

NOTE

Bypass Cabinet

Cable Name

Bypass Cabinet Cable Label or

Number

Port Silk Screen on the Power

Cabinet Parallel Board or Cable

Number

Bypass unit DL37

cable

W301_J21

J21

W303_J24

J24

ECM 8

-pin cable

W305_J22

J22

ECM system

monitoring bus

W307_J25

J25

CT cable

W309_J26

J26

Switch cable

Full configuration: 04091625-06

Standard configuration: SW1310

04091626

-23

1. Remove the covers from the top of the cabinet, drill

holes in the covers for the power cables and battery

cables, attach grommet strips to the hole edges to

protect the cables, and reinstall the covers.

Connecting Power Cables and Signal Cables

3.3

Scenario1:Routing Cables fromtheTop

(A) Signal cable hole

(B) Battery cable hole

(D) Grommet strip

2. Remove the copper bars between

the mains input and bypass input.

Bypass input power cable

(no need to connect in case

of only one mains input)

Output

power

cable

Mains input

power cable

Signal

cable

Battery

cable

3. Connect the ground cable, power cables, and signal cable.

The mains input and bypass

input share the N busbar.

The number of cables in the

figure is for reference only.

Because the switch extension

rod is sharp, exercise caution

when removing the connecting

copper bars to prevent personal

injury.

Port Bolt

Specifications Torque

Mains input M16x50 120 N·m

Bypass input M16x50 120 N·m

Battery input M16x50 120 N·m

Output M16x50 120 N·m

PE M12x35 47 N·m

NOTE

Ground

cable

The wire routed from the middle point between

positive and negative battery strings is the neutral

wire. Take a battery string consisting of 40 batteries

for example. The battery neutral wire is routed from

the middle between positive and negative battery

strings, each consisting of 20 batteries.

Scenario2: Routing Cables fromthe Bottom

1. Remove the cable covers from the bottom of the cabinet, drill holes in the covers, attach

grommet strips to the hole edges to protect the cables, and reinstall the cable covers.

Output

power cable

Mains input

power cable

Ground

cable

Signal

cable

Battery

cable

The mains input

and bypass input

share the N busbar.

2. (Skip this step if the mains input and bypass input share a power source.) Remove the

copper bars between the mains input and bypass input.

3. Connect the ground cable, power cables, and signal cable.

Bypass input

power cable

(no need to

connect in

case of only

one mains

input)

4Verifying the Installation

1. Check that there is no foreign matter at the top and bottom of the cabinets, copper bars, switches,

and the rear of units.

Front view Rear view

2. After verifying the installation, reinstall all

the covers.

3. (Remove the paper protective film from the

sealing putty.) After routing cables and

verifying cable connections, seal the gap

between cables and the cabinet using

sealing putty. Dustproof cover

4. Do not remove the dustproof cover before

power-on to prevent dust inside the UPS.

Sealing putty

Sealing putty must be used

as a whole and the gap can

be sealed only from the top.

Paper

protective film

5Powering On and Starting the UPS

1. Before powering on the UPS, ensure that the UPS has passed all check items in the UPS5000

Commissioningand Acceptance Report and Chapter 4.

2. Measure the voltage and frequency of the UPS upstream input switch. The line voltage range is

138–485 V AC, and the frequency range is 40–70 Hz.

Powering On the UPS

5.1

Close the upstream bypass and mains input switches.

(Full configuration model) Close the UPS bypass input switch, output switch, and mains input switch.

After the UPS is powered on, initialization begins. The MDU displays the Huawei logo and an

initialization progress bar.

Starting the Inverter

5.2

System User LCD Preset Password WebUI Preset Password

admin (system administrator) 000001 Changeme

operator (common user) 000001 Changeme

Initial Startup

a) If this is the initial startup, set the language, time, date, network parameters, and system

parameters on the Settings Wizard screen.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Huawei UPS Handbücher

Huawei

Huawei PowerCube 500 Bedienungsanleitung

Huawei

Huawei UPS5000-E-600K-SC Bedienungsanleitung

Huawei

Huawei UPS5000-E Series Bedienungsanleitung

Huawei

Huawei SmartLi Series Bedienungsanleitung

Huawei

Huawei UPS2000-G-6KRTS Bedienungsanleitung

Huawei

Huawei UPS5000-A series Bedienungsanleitung

Huawei

Huawei UPS5000-S-35K Bedienungsanleitung

Huawei

Huawei UPS5000-E Series Bedienungsanleitung

Huawei

Huawei UPS5000-H-1200 kVA Bedienungsanleitung

Huawei

Huawei UPS5000-H-600 kVA-FTN Bedienungsanleitung

Huawei

Huawei UPS5000-E-180 kVA Bedienungsanleitung

Huawei

Huawei UPS5000-E-****-FM series Bedienungsanleitung

Huawei

Huawei PDU8000 Series Bedienungsanleitung

Huawei

Huawei UPS5000-E-****-FM series Bedienungsanleitung

Huawei

Huawei UPS5000-A-400K-SL Bedienungsanleitung

Huawei

Huawei UPS5000-S Series Bedienungsanleitung

Huawei

Huawei UPS2000-G Series Bedienungsanleitung

Huawei

Huawei UPS5000-E-30 kVA Bedienungsanleitung

Huawei

Huawei SmartLi 2.0 Bedienungsanleitung

Huawei

Huawei UPS2000-G-3KRTL-V2 Bedienungsanleitung

Huawei

Huawei UPS2000-G-2KRTL Bedienungsanleitung

Huawei

Huawei UPS5000-H-600 kVA Bedienungsanleitung

Huawei

Huawei UPS5000-A-200K-ST Bedienungsanleitung

Huawei

Huawei SUN2000-4.95KTL-JPL0 Bedienungsanleitung

Beliebte UPS Handbücher anderer Marken

Pylontech

Pylontech Victron & Pylontech US5000 Bedienungsanleitung

Tecnoware

Tecnoware EVO DSP PLUS MM 6.8 Bedienungsanleitung

Mecer

Mecer ME-1000-WTU Bedienungsanleitung

Mustek

Mustek PowerMust 530(B) Plus Installations- und Betriebshandbuch

Emerson

Emerson Liebert NXL series Bedienungsanleitung

MAKELSAN

MAKELSAN BOXER SERIES Bedienungsanleitung

Block

Block PC-0524-400-0 Bedienungsanleitung

CyberPower

CyberPower CP585LCD Bedienungsanleitung

Eaton

Eaton 3S Montageanleitung

CyberPower

CyberPower Office Tower Series UPS 1000 Bedienungsanleitung

CyberPower

CyberPower BM100 Bedienungsanleitung

Best Power

Best Power 610 Bedienungsanleitung

Best Power

Best Power Unity/I UT3K Bedienungsanleitung

Mustek

Mustek PowerMust 400 Offline Bedienungsanleitung

Xantrex

Xantrex Trace 512 UR-UPS Bedienungsanleitung

Forza

Forza SL-1501UL Bedienungsanleitung

LEGRAND

LEGRAND keor 310081 Bedienungsanleitung

ABB

ABB Conceptpower DPA 500 Bedienungsanleitung