Hubbell KILLARK MC Series Bedienungsanleitung

Page 1 of 3

3940 Dr. Martin Luther King Drive

St. Louis, MO 63113

KIL00921465 FORM NO. K1465 06/15 ERO-8-029-15

INSTALLATION, OPERATION &

MAINTENANCE DATA SHEET

MC SERIES 45° & 90°CABLE GLANDS FOR USE WITH

TYPE MC, MC-HL, TECK90-HL, RA90, RA90-HL, AC90,

AC90-HL, ACWU90, and ACWU90HL CABLE

MC SERIES 45° & 90°CABLE GLANDS FOR

USE WITH TYPE MC, MC-HL, TECK90-HL,

RA90, RA90-HL, AC90, AC90-HL, ACWU90,

and ACWU90HL CABLE

CAUTION:

Before installing, make sure you are compliant with area classications, failure to do so may result in bodily injury,

death and property damage. Do not attempt installation until you are familiar with the following procedures. All

installation must comply with the applicable Electrical Code.

Make sure that the circuit is de-energized before starting installation or maintenance.

Verify that the installation is grounded. Failure to ground will create electrical shock hazards, which can cause

serious injury and or death.

IMPORTANT;

Please read these instructions carefully before installing or maintaining this equipment. Good electrical practices

should be followed at all times and this data should be used as a guide only.

Technical information, advice and recommendations contained in these documents is based upon information

that Killark believes to be reliable. All the information and advice contained in these documents is intended for

use only by persons having been trained and possessing the requisite skill and know-how and to be used by

such persons only at their own discretion and risk. The nature of these instructions is informative only and does

not cover all of the details, variations or combinations in which this equipment may be used, its storage, delivery,

installation, check out, safe operation and maintenance. Since conditions of use of the product are outside of the

care, custody and control of Killark, the purchaser should determine the suitability of the product for his intended

use, and assumes all risk and liability whatsoever in connection therewith.

Page 2 of 3

3940 Dr. Martin Luther King Drive

St. Louis, MO 63113

KIL00921465 FORM NO. K1465 06/15 ERO-8-029-15

For Class I, Division 2, Groups A, B, C & D

Class II, Division 1, Groups E, F & G; Class III.

Type 3 and 4. IP66. Operating Temperature Range

-50°C +60°C

1. Back Nut

2. Middle Nut

3. Grounding Spring (Captive in the Middle Nut)

4. Armor Stop

5. Elbow

6. Locking Collar

7. Potting Chamber

8. Entry Component

9. O-Ring (Captive in Entry Component)

ASSEMBLY INSTRUCTIONS

STEP A (Refer to Figure A on left)

Strip cable to suit equipment as shown above,

exposing metal armor sheath (I) and insulated

cores (II).

I = 3/4” (19mm) for ½” size glands

I = 13/16” (21mm) for ¾” size glands

I = 1” (25mm) for 1” size glands

I = 1-1/4” (32mm) for1-¼” size glands

II to suit equipment

STEP B (Refer to Figure B on left)

Push the cable through the back nut (1), middle

nut (2), and grounding spring (3). Locate the armor

stop (4) at the end of the armor as shown below. If

the conductors are too large to t through the armor

stop (4) it can be removed from the assembly. The

elbow component (5) has a built in armor stop for

larger cables. Feed the wires through the elbow

and tighten the middle nut (2) and backnut (1) to

the torque shown in Table A (Approximately hand

tight + 1 turn). This will compress the grounding

spring (3) to grip the armor for grounding.

Figure A

Figure B

Page 3 of 3

3940 Dr. Martin Luther King Drive

St. Louis, MO 63113

KIL00921465 FORM NO. K1465 06/15 ERO-8-029-15

Table A

Gland Size

Assembly

Torque (lbf-ft)

1/2” 20

3/4” 20

Figure C1

Figure C2

STEP C (Refer to Figure C on left)

If the gland is to be installed in a threaded opening

rst thread the entry component (8) into the

enclosure to prevent twisting of the cable. When

installing the entry component (8) into a NPT entry

the component should be installed hand tight and

then one additional turn with a wrench.

If the entry component (8) is installed into a thru hole

with a locknut, rst thread the entry component (8)

into the locknut. The entry component (8) should

be tightening to the torque shown in Table A

(Approximately hand tight +1 turn).

Thread the locking collar (6) onto the entry

component (8) to the torque show in Table A. This

is to prevent twisting of the cable during assembly.

Inhaltsverzeichnis

Andere Hubbell Kabel und Steckverbinder Handbücher

Hubbell

Hubbell GAI-TRONICS 400-005 Bedienungsanleitung

Hubbell

Hubbell HBLI35103Y Bedienungsanleitung

Hubbell

Hubbell IS628BT Handbuch

Hubbell

Hubbell Gleason Reel P28 Anwendungshandbuch

Hubbell

Hubbell HPS/RFL Bedienungsanleitung

Hubbell

Hubbell MINI-QUICK H MS FA1 Series Bedienungsanleitung

Hubbell

Hubbell 4-PLEX Bedienungsanleitung

Hubbell

Hubbell HBL6750 Bedienungsanleitung

Hubbell

Hubbell HBLC40123 Bedienungsanleitung

Hubbell

Hubbell INSULGRIP HBL3200RS2W Bedienungsanleitung

Hubbell

Hubbell GLEASON 602152 Bedienungsanleitung

Hubbell

Hubbell KILLARK VSIH Series Betriebsanleitung

Hubbell

Hubbell 50 AMP TWIST-LOCK Bedienungsanleitung

Hubbell

Hubbell WSB985BK Bedienungsanleitung

Hubbell

Hubbell 228FTV Handbuch

Hubbell

Hubbell Gleason Reel SZ-18 Bedienungsanleitung

Hubbell

Hubbell 50 AMP TWIST-LOCK Bedienungsanleitung

Hubbell

Hubbell Insulgrip Bedienungsanleitung

Hubbell

Hubbell 16A Bedienungsanleitung

Hubbell

Hubbell SAFETY-SHROUD TWIST-LOCK Bedienungsanleitung

Beliebte Kabel und Steckverbinder Handbücher anderer Marken

Philips

Philips SWA6310 Bedienungsanleitung

StarTech.com

StarTech.com CRJ4550PK Bedienungsanleitung

Nohau

Nohau EMUL-IP2K-PC Bedienungsanleitung

Foxun

Foxun SX-SP144E-HD4K2K Bedienungsanleitung

Philips

Philips SWA3305W Bedienungsanleitung

opticis

opticis Stretch DVIM1-1P0x Bedienungsanleitung

Volkswagen

Volkswagen VAS 6558A Bedienungsanleitung

NEXIBO

NEXIBO N-13 Bedienungsanleitung

CYP

CYP PU-1H3HBTL Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1784-u2dhp Bedienungsanleitung

Global Caché

Global Caché Flex Link Blaster Bedienungsanleitung

Hauppauge

Hauppauge USB-Live2 Bedienungsanleitung

Fenix

Fenix MPSV 15 Bedienungsanleitung

BEGA

BEGA 71 085 Bedienungsanleitung

Tesla

Tesla HPWC Bedienungsanleitung

GAMERON

GAMERON LUXURY TV CABLE Bedienungsanleitung

molex

molex Milli-Grid Dual row 87568 Series Bedienungsanleitung

Burndy

Burndy Continental Industries thermOweld CRE-7 Bedienungsanleitung