Hubbell GAI-TRONICS TempSense TS200 Bedienungsanleitung

Pub. 42004-566A 
 
G A I - T R O N I C S ®
A H U B B E L L C O M P A N Y 
TempSense Models TS200/TS200W 
TA B L E O F CO N T E N T S 
GAI-TRONICS 3030 KUTZTOWN RD. READING, PA 19605 USA 
610-777-1374 ◼800-492-1212 ◼Fax: 610-796-5954 
VISIT WWW.GAI-TRONICS.COM FOR PRODUCT LITERATURE AND MANUALS 
Confidentiality Notice.....................................................................................................................1 
General Information.......................................................................................................................1 
Installation ......................................................................................................................................2 
Camera Location.....................................................................................................................................2 
Wall Mount...........................................................................................................................................3 
Pole Mount............................................................................................................................................3 
VESA Mount ........................................................................................................................................3 
Stand Mount..........................................................................................................................................4 
Connection...............................................................................................................................................4 
Model TS200 ........................................................................................................................................ 4 
Model TS200W.....................................................................................................................................4 
Configuration..................................................................................................................................5 
TempSense TS200...................................................................................................................................5 
TempSense TS200W...............................................................................................................................5 
Calibration...............................................................................................................................................7 
Operation.........................................................................................................................................8 
Environment............................................................................................................................................8 
Subject Preparation................................................................................................................................8 
Scanning Subjects...................................................................................................................................8 
Specifications ..................................................................................................................................9 
Electrical..................................................................................................................................................9 
Mechanical...............................................................................................................................................9 
FLIR Camera..........................................................................................................................................9 

Pub. 42004-566A

GAI-TRONICS®

A HUBBELL COMPANY

TempSense Models TS200/TS200W

GAI-TRONICS 3030 KUTZTOWN RD. READING, PA 19605 USA

610-777-1374  800-492-1212  Fax: 610-796-5954

VISIT WWW.GAI-TRONICS.COM FOR PRODUCT LITERATURE AND MANUALS

Confidentiality Notice

This installation and operation manual contains sensitive business and technical information that is

confidential and proprietary to GAI-Tronics. GAI-Tronics retains all intellectual property and other rights

in or to the information contained herein, and such information may only be used in connection with the

operation of your GAI-Tronics product or system. This manual may not be disclosed in any form, in

whole or in part, directly or indirectly, to any third party.

General Information

The TempSense Models TS200/TS200W measure and capture EBT (elevated body temperature) or EST

(elevated skin temperature) of subjects moving through the TempSense’s FOV (field of view). The

TempSense module consists of one FLIR® (forward looking infra-red) camera and one standard video

camera sharing the same FOV in a wall, pole, tripod, or microphone stand mountable enclosure. The

TS200/TS200W captures 608 × 464 resolution images on both cameras and sends them via email to the

an email recipient when the highest temperature in the FOV is above the configurable threshold

temperature.

Figure 1. TempSense Models TS200/TS200W

Pub. 42004-566A

TempSense Models TS200/TS200W Page 2 of 9

P:\Standard IOMs - Current Release\42004 Instr. Manuals\42004-566A.docx

03/21

Installation

NOTE:The accuracy of the TempSense TS200/TS200W requires individual subjects pass within two to

six feet of the thermal imaging camera lens. Results with different camera positions may vary.

Thermal imaging camera accuracy improves as the subject moves closer to the camera.

Camera Location

Locate the TempSense TS200/TS200W so that people in a queue individually pass through the two

cameras’ shared FOV while facing the cameras. Each subject scanned should come within two to six feet

of the cameras. The ideal height for camera installation is 5 feet 5 inches above the floor. Installation at a

higher location requires aiming the TS200/TS200W downward so that each subject’s forehead passes

through the center of the FOV (see Figure 2 and Figure 3).

Figure 2. SAMPLE FIGURE Camera Positioning (Side View)

Figure 3. SAMPLE FIGURE Camera Positioning (Top View)

Pub. 42004-566A

TempSense Models TS200/TS200W Page 3 of 9

P:\Standard IOMs - Current Release\42004 Instr. Manuals\42004-566A.docx

03/21

Wall Mount

Mount the TempSense TS200/TS200W to a

wall as follows (see Figure 4):

OTE

: GAI-Tronics recommends spacing

the TempSense Model TS200

approximately ¼ inch from any flat

surface to allow air flow.

1. Secure the mounting plate (TS200: see

Figure 6, TS200W: see Figure 7) to a flat

surface using (customer supplied)

hardware.

Use the four VESA mount holes to

secure the mounting plate to the wall.

No. 8 screws fit through the 0.190-inch

threaded VESA mounting holes (see

Figure 4).

2. Secure the TS200/TS200W to the

mounting plate using the four included

#6-32 screws.

Pole Mount

Mount the TempSense TS200/TS200W to a

pole (see Figure 5) as follows:

1. Secure the TS200 (see Figure 6) or

TS200W (see Figure 7) mounting plate,

to a pole using (customer supplied)

worm-drive clamps

2. Secure the TS200/TS200W to the

mounting plate using the four included

#6-32 screws.

VESA Mount

Attach a VESA (video electronics standards

association) mount to the mounting plate

with the included #10-24 screws and

washers (TS200: see Figure 6, TS200W: see

Figure 7).

OTE

: The TS200/TS200W includes four

#10-24 × 0.38-inch long screws to

attach a customer supplied VESA

mount. Do not use any screws

other than the included #10-24

screws to attach the VESA mount

to the TS200/TS200W’s mounting

plate.

Figure 4. Wall-Mount Detail

Figure 5. Pole-Mount Detail

Figure 6. Mounting Plate Detail (Model TS200)

Pub. 42004-566A

TempSense Models TS200/TS200W Page 4 of 9

P:\Standard IOMs - Current Release\42004 Instr. Manuals\42004-566A.docx

03/21

Stand Mount

Mount the TS200/TS200W to a tripod or

microphone stand using the included L-

bracket (see Figure 8).

1. Secure the mounting plate (TS200: see

Figure 6, TS200W: see Figure 7) to the

TS200/TS200W using the four

included #6-32 screws.

2. Secure the L-bracket to the mounting

plate using the two included #8-32 flat

head machine screws (see Figure 9).

3. Secure the L-bracket to a microphone

stand or tripod (see Figure 8).

Connection

Model TS200

Plug a Category 5e or better Ethernet cable

with RJ45 plug from a PoE switch port into

the TS200’s Ethernet jack pigtail. The

TS200's IR sensor has a white LED that

blinks slowly for 40 seconds, then changes

to a fast blink.

NOTE: If the IR sensor LED does not

flash, press the sensor into its

socket using a soft cloth, then

reboot the device.

The Model TS200 boots up and is ready for

configuration (see the Configuration

section) or scanning subjects (see the

Operation section) after adjusting to its

environment (about 10–30 minutes).

Model TS200W

1. Plug the included power supply into the

power cord pigtail on the TS200W.

2. Plug the power supply into a 120 V ac

outlet.

The TS200W's IR sensor has a white LED that blinks slowly for 40 seconds, then changes to a fast blink.

NOTE: If the IR sensor LED does not flash, press the sensor into its socket using a soft cloth, then reboot

the device.

The Model TS200W boots up and is ready for configuration (see the Configuration section) or scanning

subjects (see the Operation section) after adjusting to its environment (about 10–30 minutes).

Figure 7. Mounting Plate Detail (Model TS200W)

Figure 8. TS200/TS200W L-Bracket Detail

Figure 9. L-Bracket Attachment for Tripod/Microphone

Stand Mounting

Pub. 42004-566A

TempSense Models TS200/TS200W Page 5 of 9

P:\Standard IOMs - Current Release\42004 Instr. Manuals\42004-566A.docx

03/21

Configuration

The TempSense TS200 and TS200W have a built in webserver for configuration and calibration of the

TempSense device.

TempSense TS200

Configure the TempSense TS200 before calibrating it or using it to scan subjects:

1. Plug a Category 5e or better Ethernet cable with RJ45 plug from a PoE switch port into the TS200’s

Ethernet jack pigtail.

The TempSense TS200 boots up with a static, class CIP address, set to 192.168.1.55.

2. Wait several minutes for the unit to boot and come up to normal operating temperature.

3. Configure a PC to access the TempSense device on the class Cnetwork 192.168.1.x.

4. Open a web browser and enter 192.168.1.55 in the address bar.

The TempSense management webpage contains sections of parameters for defaults (see Table 1),

network (see Table 2), SMTP (see Table 3) , and time (see Table 4).

5. Configure all settings and click APPLY CHANGES AND RESTART.

The unit reboots with the configured settings.

NOTE:If the network mode is DHCP but no DHCP server exists, the unit falls back to IP address

192.168.1.55.

TempSense TS200W

Configure the TempSense TS200W before calibrating it or using it to scan subjects as follows:

1. Plug the included power supply into the TS200W’s power cord pigtail.

2. Plug the power supply into a 120 V ac outlet.

3. Wait several minutes for unit to boot and come up to normal

operating temperature.

The TS200W boots up and creates a wireless network with

following properties:

•WiFi frequency: 2.4 GHz

•SSID: ThermalScanner

•IP address: 192.168.4.1

•subnet mask: 255.255.255.0

•password: GAItronics

4. Use a PC to access the ThermalScanner WiFi access point.

Password: GAItronics

5. Open a web browser and enter 192.168.4.1 in the address bar to

access and authenticate to the TS200W’s management webpage.

The TempSense management webpage contains sections of

parameters for defaults (see Table 1), network (see Table 2),

SMTP (see Table 3) , and time (see Table 4)

Figure 10. Model TS200W

Factory Reset

Pub. 42004-566A

TempSense Models TS200/TS200W Page 6 of 9

P:\Standard IOMs - Current Release\42004 Instr. Manuals\42004-566A.docx

03/21

6. Configure all settings and click APPLY CHANGES AND RESTART.

The unit reboots and tries to connect to the configured wireless network.

FACTORY RESET:To reset the TS200W, use a jumper cap to short pins 39-40 on the 40-pin header

for 5 seconds. The TempSense resets itself to factory original settings, reboots,

and re-broadcasts as an access point with the original WiFi properties (see Figure

10).

NOTE:If the network mode is DHCP but no DHCP server exists, the unit falls back to IP address

192.168.1.55.

Table 1. Default Parameters

Parameter

Description

Value:

Description

The TempSense device description.

[MODEL]-[Last Three

Octets of MAC ADDRESS]

degreesf

Select Yes to display the temperature in Fahrenheit or

No to display the temperature in Celsius.

Yes | No

automatic_scan_timeout

The period before scanning restarts after the

measured temperature drops below the threshold

temperature.

0–100, 5(seconds)

Offset

The value to add to or subtract from the temperature

measured by the TempSense

−10 to +10 °F, 0 °F

−6 to +6 °C, 0°C

Threshold

The measured temperature that triggers the

TempSense event.

+60 to +120 °F

+16 to + 48 °C

Model

The factory configured TempSense model number.

TS200 | TS200W

Table 2. Network Parameters

Parameter

Description

Value:

ssid_hidden

Set to Yes if connecting to a wifi network that dos not

broadcast its SSID. Set to No if connecting to a wifi

network that broadcasts its SSID.

Yes | No

ip_addr

IP version 4 address of the TempSense

TS200: 192.168.1.55

TS200W: 192.168.4.1 wifi

ssid

The system set identifier for the wireless network

Case sensitive string

ThermalScanner

ssid_pass

The password for the SSID the TS200/TS200W will

connect to.

GAItronics

nw_mask

IP version 4 network mask

255.255.255.0

nw_gateway

IP version 4 address of the network router

0.0.0.0

dns_addr

IP version 4 address for a DNS server

0.0.0.0

hostname

The common name for this device on the network.

[MODEL]-[Last Three

Octets of MAC ADDRESS]

ip_addr_mode

Static or DHCP

static

Pub. 42004-566A

TempSense Models TS200/TS200W Page 7 of 9

P:\Standard IOMs - Current Release\42004 Instr. Manuals\42004-566A.docx

03/21

Table 3. SMTP Parameters

Parameter

Description

Value:

username

The username for the SMTP server mailbox

(string) None

server

the SMTP server’s IP Version 4 address

valid IPv4 address or FQDN

(Fully Qualified Domain Name)

0.0.0.0

security

SMTP security protocol in use

TLS, SSL, None

password

the SMTP password for the mail account

(string)

recipient

The receiver’s email address this TempSense device

sends email to.

valid SMTP email address

None

port

The I/O memory address of the SMTP service on the

host computer

0–65535, 587

Table 4. NTP Parameters

Parameter

Description

Value:

time_server

IP version 4 address for an NTP server

valid IPv4 address or FQDN

(string) 0.0.0.0

time_zone

The offset from UTC

Select the offset from UTC using

the roll box control.

Calibration

1. Place an object of known temperature in the field of view of the TS200/TS200W at the appropriate

height and distance (see the Camera Location section).

2. Login to the webserver and press the CALIBRATE THRESHOLD AND OFFSET button.

3. While watching the temperature of the object in the IR video feed (left side), slide the OFFSET slider

to adjust the on-screen temperature until it displays the known temperature (see Figure 11).

4. Adjust the TEMP THRESHOLD to the desired temperature for the TS200/TS200W to send an email to

the recipient to alert them when a subject exceeds this temperature.

The TS200/TS200W captures both an IR and normal picture when the temperature exceeds the TEMP

THRESHOLD value. It then waits the automatic_scan_timeout period after the temperature drops

below the threshold temperature before scanning resumes.

Pub. 42004-566A

TempSense Models TS200/TS200W Page 8 of 9

P:\Standard IOMs - Current Release\42004 Instr. Manuals\42004-566A.docx

03/21

Figure 11. Temperature Superposition and Calibration

Operation

Environment

Environmental considerations for the Models TS200/TS200W NCIT (non-contact infra-red thermometer)

performance:

•Use the temperature scanning feature of the TS200/TS200W in a draft-free space that is out of direct

sunlight and away from radiant heat sources.

•The optimal environment for the TS200/TS200W temperature sensor is between 60.8–104 ºF (16–40

ºC) with the relative humidity below 85 percent.

•Allow the TS200/TS200W to operate in the testing environment for 10–30 minutes to adjust to its

environment before scanning personnel.

Subject Preparation

To obtain accurate skin temperatures, ensure that the subject has not:

•been wearing a hat, scarf, heavy clothing, etc.

•underwent recent physical exertion

•just entered from a much lower temperature environment

•recently used facial cleaning products

•engaged in any other act that may affect their skin temperature.

Scanning Subjects

When a subject with a temperature exceeding the configured threshold enters the IR camera's FOV:

•The TempSense TS200/TS200W sends an email to the SMTP recipient containing still images of the

IR and standard camera's FOV.

•The TS200/TS200W image includes the temperature ±Offset superimposed in the IR picture.

Pub. 42004-566A

TempSense Models TS200/TS200W Page 9 of 9

P:\Standard IOMs - Current Release\42004 Instr. Manuals\42004-566A.docx

03/21

Specifications

Electrical

Power:

TS200 .................................................................................................................................................PoE

TS200W......................................................................................................................................120 V ac

Mechanical

Dimensions .............................................................7.26 H × 5.76 W × 1.5 D in (184.4 × 146.3 × 38.1 mm)

Weight...................................................................................................................................... 2.0 lb (0.9 kg)

FLIR Camera

Horizontal FOV .........................................................................................................................................51°

Vertical FOV.........................................................................................................................................38.25°

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis