Humminbird 350TX 350TX Bedienungsanleitung

WARNING: Dis-assembly and repair of this electronic unit should only be performed

by authorized service personel. Any modification of the serial number or attempt to

repair the original equipment or accessories by unauthorized individuals will void the

warranty. handling and/or opening this unit may result in exposure to lead, in the form

of solder.

Warning: This product contains lead, a chemical known to the State of

California to cause cancer and birth defects and other reproductive harm.

INSTALLATION PREPARATION . . . . . . . . . . . . . . . . . . . . . . . . . . 2

PARTS SUPPLIED . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

ACCESSORIES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

INSTALLATION OVERVIEW . . . . . . . . . . . . . . . . . . . . . . . . . 2

ALTERNATIVE TRANSDUCERS AND MOUNTING METHODS . 4

TRANSDUCER EXCHANGE . . . . . . . . . . . . . . . . . . . . . . . . 5

USING THE 350TX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

HOW SONAR WORKS . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

SIMULATOR OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . 7

WHAT YOU SEE ON SCREEN . . . . . . . . . . . . . . . . . . . . . . . 8

CONTROL FUNCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . 11

MENU FUNCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

ADVANCED FEATURES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

USING THE DIAGNOSTIC FEATURE . . . . . . . . . . . . . . . . . . 25

USING ALTERNATIVE TRANSDUCERS . . . . . . . . . . . . . . . . 26

MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

CUSTOMER SUPPORT . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

TABLE OF CONTENTS

Rev. 11016E

INSTALLATION PREPARATION

PARTS SUPPLIED

Before installing your 350TX, please ensure the following parts are included

in the box:

• 350TX fishfinder

• Transducer with 6m (20') of cable and mounting hardware kit

• Mounting system and mounting hardware kit

• 2m (6') power cable

• Publications kit

If any of these items is missing, contact your local Humminbird dealer.

ACCESSORIES

Humminbird offers a wide assortment of accessories that complement and

expand the capability of your new 350TX. These accessories are designed

with the same high standards and are backed by the same one-year

warranty. The Humminbird Accessory catalog included with your unit

contains descriptions of the many accessories available and ordering

information. All Humminbird accessories are available through your full-

service Humminbird dealer.

INSTALLATION OVERVIEW

The 350TX consists of two primary components to install: the control head

and the transducer.

The control head contains the sonar transmit and receive circuitry, as well

as the user controls and display. It should be installed in a location that

provides access to the controls and visibility while in use. The control head

mounts on a quick disconnect mounting system that swivels and tilts

providing flexibility for viewing from almost anywhere on the boat.

The transducer converts electrical energy from the transmitter into

mechanical pulses or sound waves. The transducer also receives the

reflected sound waves and converts them back into electrical signals for

INSTALLATION PREPARATION

INSTALLATION OVERVIEW

display on the control head. It should be installed in contact with the

surface of the water in an area that has smooth water flow - usually on the

transom of the boat. There are several mounting options for the

transducer. Review the following section to determine the method that

works for you and your boat.

Determining How to Mount the Transducer

The 350TX includes a model XT-6-TB-90

transducer. This transducer can be

mounted on the transom of the boat, or

bonded to the inside of a fiberglass hull

boat.

The transom installation, which is the

most widely used, places the transducer

on the outside of the boat hull. This

technique produces the least signal loss,

and provides a way to adjust the

transducer after installation. The

mounting hardware included is designed

to protect both the boat and the

transducer should the boat strike debris

in the water or when trailering.

As an alternative to transom mounting, it is

possible on many fiberglass-hulled

boats to glue the transducer on the

inside of the boat hull. Since

fiberglass has similar sonar character-

istics as water, the sonar signal can

pass through the boat hull with

minimal loss. The hull of the boat

must be single layer construction

(not double-hulled). Also, any air

trapped in the lamination of the

fiberglass would prevent the sonar

signal from passing through.

Transom Mounted Transducer

Inside the Hull Mounted Transducer

Inside the hull installations require no holes be drilled into the boat and

through experimentation, high-speed operation comparable to transom

mounting can be achieved. Two part, slow cure epoxy is required to glue

the transducer in place.

ALTERNATE TRANSDUCERS AND MOUNTING METHODS

The 350TX comes with everything necessary for installation and operation

on most boats. However, there are several situations which may require a

different type of transducer. Inboard boats, wood or metal hulls, and sail

boats create unique transducer mounting needs. Alternate transducers and

mounting methods are detailed below.

Portable Mounting

The standard transducer can be adapted for

portable installations using part number MHX-

PT2. This accessory adapts your transducer to a

suction cup mount for temporary installation on

the boat hull or other surface.

Trolling Motor Mounting

The standard transducer can also be adapted to

mount on most trolling motors using part number

AD-STM-7. This accessory includes a bracket and

hose clamp that allows mounting the transducer

to the body of most trolling motors.

Thru-Hull Mounting

Thru-hull transducers install through a hole

drilled in the hull of the boat. Larger boats or

boats with inboard motors create turbulence

that make transom mounting ineffective. Also,

hulls that are very thick or are double layered, or

made from materials such as wood or metal,

(which do not conduct sonar signals) make

inside the hull mounting inadvisable.

INSTALLATION PREPARATION

ALTERNATE TRANSDUCERS AND MOUNTING METHODS

Thru-hull mounting may require the use of a fairing block to level the

transducer with the waterline. Also, since special tools and knowledge may

be required to perform this type of installation it is best to refer to a

qualified marine technician.

TRANSDUCER EXCHANGE

Other transducers are available as replacements for the standard

transducer. You may exchange your new and unassembled transducer for

another type. Contact your local distributor for details. Some transducers

may have additional costs. Refer to the Accessory catalog or call your

distributor for information.

BEGINNING INSTALLATION

Now that you have determined the transducer mounting method, you can

begin installation of the 350TX. The fold out installation guide included

provides detailed step by step instructions for installation of the control head

and transducer. For transom mount transducer installations using the

XT-6-TB-90, you will need the mounting template at the rear of this manual.

In addition to the parts included you need the following for installation and

operation:

•A powered hand drill and various drill bits

•Phillips and flat-head screw drivers

•A ruler or measuring tape

•Pen or pencil

•12 volt power source (your boat’s battery)

•A 1-amp fuse

•A fuse holder (if you are wiring directly to the boat’s battery)

•Silicone sealant (for sealing drilled holes)

•2-part, slow-cure epoxy (for inside the hull transducer installations)

INSTALLATION PREPARATION

TRANSDUCER EXCHANGE

USING THE 350TX

HOW SONAR WORKS

Your Humminbird unit uses sonar to

locate and define underwater objects,

define the bottom terrain, as well as

determine distance.

Sonar technology is based on sound

waves. Your Humminbird unit sends

out a sound wave signal. With this

signal it determines distance by

measuring the time between the

transmission of the sound wave and

when the sound wave is reflected off

an object. Your Humminbird uses the

reflected signal to interpret location,

size and composition of an object.

Sonar is very fast. A sound wave can travel from the surface to a depth of

70m (240') and back again in less than ¹⁄₄ of a second. It is unlikely that

your boat can "outrun" this sonar signal.

The 350TX is a dual frequency, tri-beam unit, and generates three distinct

sonar signals - one narrow, two wide. Each signal is optimized for a

particular purpose. First, the center beam transmits at a frequency of

200 kHz in a 20°(narrow) symmetrical pattern for greater depth capability

and excellent detail. Information from this center beam is used to draw the

graphic representation of the bottom on the display.

The left and right beams are generated at 455 kHz for increased sonar

resolution and are shaped in an elliptical pattern for greater area of

coverage. (45ºside to side, and 16ºfront to back.) Information from these

two beams in conjunction with the center beam is used to accurately

detect the presence and location of fish.

The combination of the three beams and dual frequencies, provides the best

possible combination of a large area of coverage and a high level of detail.

USING THE 350TX

SIMULATOR OPERATION

Actual depth capability depends on factors such as bottom hardness, water

conditions, and transducer installation. Units will typically read to deeper

depths in fresh water than in salt water.

SIMULATOR OPERATION

The 350TX contains a simulator that allows

you to use the unit as if you are on the water.

The simulator is invaluable for learning how

to operate the 350TX.

There are two ways to start the simulator. If

the unit is powered off, press and hold the

POWER button for approximately three

seconds until you hear a continuous chirp.

The simulator can also be started by selecting the Simulator option on the

start-up screen after you power-up the unit. When this screen is shown,

simply press the DOWN ARROW until “Simulator”is highlighted. When the

screen times out, the unit will be in simulator mode.

When in simulator operation, the 350TX responds to control inputs as if it

is in actual operation, so feel free to experiment, or to customize the unit

for your particular operation.

To exit Simulator mode, power the unit off.

When in simulator mode, the word “simulator” occasionally

scrolls across the display indicating the information on-screen is

not real sonar data.

FEATURE MEMORY

If your 350TX is installed with a transducer connected, any changes you

make to the set-up or User Options (see Control Functions) while in

Simulator are retained in the unit’s memory. This allows you to use

simulator to experiment with the various set-up options, and retain your

selected settings for normal operation.

If you are using the 350TX in Simulator when no transducer is connected,

any selected options are lost when the unit is powered off. The 350TX will

return to Factory Settings, or options selected when last used with a

transducer, if no transducer is connected.

IMPORTANT: A transducer must be connected to the 350TX in

order to retain user settings selected when in simulator mode. If

no transducer is detected, the unit defaults to pre-selected

options when powered off.

What You See On-Screen

Your 350TX uses a 128 V x 64 H

matrix FSTN LCD display. This display

provides outstanding viewability in all

light conditions over a wide range of

temperatures.

At initial power-up, the 350TX uses

settings that were set at the factory.

After initial use, the 350TX will

remember the settings you enter.

There are several elements on-screen

that are common to all modes of

operation.

Temperature/Speed. The initial screen layout takes one of two basic

forms depending on whether the optional Temp/Speed accessory is

installed. Figure A shows the default view when the Temp/Speed accessory

is installed. Figure B shows the default view when the Temp/Speed

accessory is not installed.

Depth. The digital depth number shows the water depth directly beneath

the transducer location.

Depth Range. The depth range is shown to the right of the screen. The

upper number is 0 indicating the surface of the water. The lower number

is one of the nine depth ranges available that best match the depth of the

water. As the depth of the water changes, the range changes as necessary

in order to retain a bottom representation on-screen.

USING THE 350TX

WHAT YOU SEE ON-SCREEN

Figure A

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Humminbird Fischfinder Handbücher

Humminbird

Humminbird ProFlasher Bedienungsanleitung

Humminbird

Humminbird i-PILOT LINK Bedienungsanleitung

Humminbird

Humminbird 323 Bedienungsanleitung

Humminbird

Humminbird 110 Fishin' Buddy Bedienungsanleitung

Humminbird

Humminbird TRACKER PRO 128 Bedienungsanleitung

Humminbird

Humminbird 700 Seris Bedienungsanleitung

Humminbird

Humminbird 110 Fishin' Buddy Bedienungsanleitung

Humminbird

Humminbird HELIX 7 SERIES Bedienungsanleitung

Humminbird

Humminbird Helix Series Bedienungsanleitung

Humminbird

Humminbird CVR1000 Bedienungsanleitung

Humminbird

Humminbird Smartcast RF20 Bedienungsanleitung

Humminbird

Humminbird TCR ID-10 Bedienungsanleitung

Humminbird

Humminbird 967C Bedienungsanleitung

Humminbird

Humminbird Platinum cartography Bedienungsanleitung

Humminbird

Humminbird 698ci HD SI Combo Bedienungsanleitung

Humminbird

Humminbird Matrix 47 Bedienungsanleitung

Humminbird

Humminbird Ultima Bedienungsanleitung

Humminbird

Humminbird 587ci Combo Bedienungsanleitung

Humminbird

Humminbird Wide 2000 Bedienungsanleitung

Humminbird

Humminbird 1100CI Series Bedienungsanleitung

Humminbird

Humminbird 581i DI Combo Bedienungsanleitung

Humminbird

Humminbird 530508-3_A Bedienungsanleitung

Humminbird

Humminbird Helix Series Bedienungsanleitung

Humminbird

Humminbird Platinum ID 600 Bedienungsanleitung

Beliebte Fischfinder Handbücher anderer Marken

Norcross

Norcross D10DX.01T Bedienungsanleitung

Hawkeye Mfg

Hawkeye Mfg FishTrax FT1PXC Bedienungsanleitung

JRC

JRC JFV-700HP Bedienungsanleitung

JRC

JRC FF50 Bedienungsanleitung

Navman

Navman FISH 4200 Bedienungsanleitung

Furuno

Furuno FCV-628 Bedienungsanleitung

Raytheon

Raytheon V720 Bedienungsanleitung

Norcross

Norcross ML100TDR ML100R ML100DR ML100tr Bedienungsanleitung

Furuno

Furuno FCV-627 Bedienungsanleitung

Fuso

Fuso FEG-881 Bedienungsanleitung

Bottom Line

Bottom Line Fishin Buddy 4200 Bedienungsanleitung

Lowrance

Lowrance HOOK-4x Bedienungsanleitung

Apelco

Apelco LFC-6550 Bedienungsanleitung

Lowrance

Lowrance HDS Carbon Bedienungsanleitung

Apelco

Apelco 6760 Bedienungsanleitung

Chinavision

Chinavision CVXR-OG34 Bedienungsanleitung

Marcum Technologies

Marcum Technologies troller 2.0 combo Bedienungsanleitung

Chasing

Chasing CanFish CF1 Bedienungsanleitung