Hunter XC Hybrid Betriebsanleitung

XC Hybrid

For use with XCH Plastic, XCH Stainless Steel,

and XCH Solar Panel controllers

Owner’s Manual and

Installation Instructions

PRG

ACTIVE

SENSOR BYPASS

INTRODUCTION ........................................................... 1

XC HYBRID COMPONENTS ......................................... 2

MOUNTING THE CONTROLLER TO THE WALL............5

CONNECTING VALVES..................................................5

INSTALLING BATTERIES............................................. 6

CONNECTING A MASTER VALVE.................................7

CONNECTING A WEATHER SENSOR .......................... 8

Testing the Weather Sensor .................................... 8

Manually Bypassing the Weather Sensor ................ 8

POWER FAILURES....................................................... 9

INSTALLING THE TRANSFORMER (OPTIONAL) ........ 9

WATERING SCHEDULE............................................... 10

PROGRAMMING THE CONTROLLER ..........................11

Setting the Date and Time .....................................11

Setting the Program Start Time(s) .........................11

Eliminating a Program Start Time .......................... 12

Setting Station Run Times ..................................... 12

Setting Days To Water ........................................... 12

Selecting Specific Days of the Week to Water........ 12

Selecting Odd or Even Days to Water .................... 13

Selecting Interval Watering ................................... 13

Setting Event Day(s) Off ........................................ 13

Automatic Watering............................................... 14

System Off ............................................................. 14

Programmable Rain Off ......................................... 14

Seasonal Adjustment ............................................ 14

Manually Run a Single Station ............................... 15

Manually Run All Stations ...................................... 15

One Touch Manual Start and Advance.................... 15

ADVANCED FEATURES .............................................. 16

Programmable Sensor Override............................. 16

Test Program of All Stations................................... 16

Easy Retrieve™ Program Memory.......................... 17

Programmable Delay Between Stations................. 17

Clearing the Controller's Memory/

Resetting the Controller......................................... 17

POLE MOUNT INSTRUCTIONS................................... 18

TROUBLESHOOTING GUIDE ......................................20

SPECIFICATIONS........................................................ 21

Operating Specifications........................................ 21

ELECTRICAL SPECIFICATIONS .................................. 21

Explanation of Symbols.......................................... 21

CERTIFICATE OF CONFORMITY TO EUROPEAN

DIRECTIVES ...............................................................22

TABLE OF CONTENTS

INTRODUCTION

The XC Hybrid is a full-featured irrigation

controller that combines maximum programming

exibility with the versatility of battery operation

for a wide range of installations. Using DC latching

solenoid technology, the XCH is ideal for remote

or isolated installations that do not have access to

AC power. The XCH is truly a hybrid controller that

can operate from a wide variety of power sources.

In situations where AC power is available, a plug-in

transformer can be used to supply power to the

controller. A factory-installed solar panel version

(XCH-XXX-SSP) allows for a continuous supply

of power to the controller without the need for

replaceable batteries.

PRG

ACTIVE

SENSOR BYPASS

XC HYBRID COMPONENTS

PRG

MO TU WE TH FR SA SU ODD

EVEN

AM PM

%24HR

2,4...30

1,3...29

2 3 911

4618

12 13 5 10 14

16 B

ACTIVE

SENSOR BYPASS

PLASTIC VERSION

STAINLESS STEEL VERSION

STAINLESS STEEL SOLAR

VERSION

A – LCD DISPLAY

1. Run Times – Allows user to set each valve station

run time from 1 minute to 4 hours.

2. Start Times – Allows 1 to 4 start times to be set in

each program.

3. Station Number – Indicates currently selected station

number.

4. Program Designator – Identifies program (A, B, or C)

in use.

5. Day of the Week – Identifies day of the week.

6. Interval Watering – Identifies month when

programming current date.

7. Odd/Even Watering – Identifies if Odd or Even

watering has been selected.

8. Flashing Sprinkler – Indicates that watering is

taking place.

9. System Off – Allows user to discontinue all

programs and watering. Also allows the user to

set the programmable "rain off," which stops

watering for a period from 1 to 7 days.

10. Umbrella – Indicates that the rain sensor is active.

11. Seasonal Adjustment – Allows the user to make

run time changes according to the seasons without

reprogramming the controller. Bars on the left allow

quick visual reference to the seasonal adjustment

percentage.

12. Rain Drop – Indicates watering will occur on the

selected day.

13. Crossed Rain Drop – Indicates the watering will

NOT occur on the selected day.

14. Calendar – Indicates interval watering schedule

has been programmed. Icon also appears when

programming the current day.

B – WIRING COMPARTMENT

15. Terminal Strip – Use to attach transformer, sensor,

and valve wires from their source to the controller.

16. Reset Button – Use to reset the controller.

17. Battery Holder – Holds six AA alkaline batteries.

C  CONTROL BUTTONS

Button – Increases the selected item ashing in the

display.

Button – Decreases the selected item flashing in the

display.

Button – Returns selected flashing display to previous

item.

Button – Advances the selected flashing display to the

next item.

Button – Selects program A, B, or C for different

watering zone requirements.

18. Sensor Bypass Switch.

XC HYBRID COMPONENTS CONTINUED

D  DIAL SETTINGS

Run – Normal dial position for all controller automatic

and manual operation.

Current Time/Day – Allows current day and clock

time to be set.

Start Times – Allows 1 to 4 start times to be set in

each program.

Run Times – Allows user to set each valve station

run time from 1 minute to 4 hours.

Water Days – Allows the user to select interval

days to water.

Seasonal Adjustment – Allows user to make run

time changes according to the seasons without

reprogramming the controller. Bars on the left

allow quick visual reference to the seasonal

adjustment percentage.

1Manual-One Station – Allows user to activate a

one-time watering of a single valve.

ALL Manual-All Stations – Allows user to activate a

one-time watering of all valve stations or a few

selected stations.

System Off – Allows user to discontinue all

programs and watering. Also allows the user

to set the programmable rain off, which stops

watering for a period from 1 to 7 days.

E  EXTERNAL TRANSFORMER OPTIONAL

A plug-in transformer can be used to supply AC power

to the controller.

MOUNTING THE CONTROLLER TO THE WALL

1. Secure one screw into the wall. Install screw anchors if

attaching to drywall or masonry wall.

2. Slide the keyhole on top of the controller over the screw.

3. Secure the controller in place by installing screws in the

holes below the terminal strip.

CONNECTING VALVES

NOTE: The XCH operates DC latching solenoids only (order

Hunter P/N: 458200). 24 VAC solenoids will NOT operate

with the XCH. DC solenoids can be easily identied by red

and black leads. The red lead is attached to the station

output, while the black lead is attached to the common wire.

1. Route valve wires between the control valve location and controller.

2. At valves, attach a common wire to the black solenoid wire on all

valves. Attach a separate control wire to the remaining red wire

of each valve. All wire connections should be done using

waterproof connectors.

3. Route the valve wires through the conduit. Attach the conduit

through the bottom right side of the controller.

4. Secure the valve common wire to the C (Common) screw on the

terminal strip. Attach each of the individual valve control wires

to the appropriate station terminals and tighten their screws.

Valve Common Wire (Black Leads)

Valve 1

Valve 2

Valve 3

Valve 4

Station Wires

(Red Leads)

WIRE SIZE DISTANCE FROM VALVE TO

CONTROLLER

18 AWG (0.8 mm2)550' (168 m)

16 AWG (1.3 mm) 870' (265 m)

14 AWG (2.1 mm) 1,380' (421 m)

12 AWG (3.3 mm) 2,200' (671 m)

Battery Power

The XC Hybrid Plastic operates on six AA alkaline batteries,

and the XC Hybrid Stainless uses six alkaline C batteries. A

battery carrier is supplied with your controller. Insert the

batteries as indicated on the battery carrier.

• XC Hybrid-Plastic Battery Install Connect the battery

connector inside the access compartment to the battery

carrier and insert the carrier into the lower le side of the

controller as shown.

• To access battery carrier on the XC Hybrid Stainless,

remove the screw in the top center of the controller and

swing the facepack down as shown.

• XC Hybrid Stainless Steel Solar comes out-of-the-box

ready to install and program. Place the controller in full

sunlight. Turn the dial to the Run position to activate solar

charging.

INSTALLING BATTERIES

PRG

ACTIVE

SENSOR BYPASS

Battery Carrier

XC Hybrid Stainless

XC Hybrid-Plastic

XC Hybrid Stainless

Steel Solar

CONNECTING A MASTER VALVE

NOTE: Complete this section only if you have a

master valve installed in your irrigation system. A

master valve is a “normally closed”valve installed

at the supply point of the main line that opens only

when the controller initiates a watering program.

1. At the Master Valve, attach the common wire to the black

solenoid wire of the valve. Attach a separate control wire

to the remaining red solenoid wire.

2. The common wire should be attached to the Cterminal

inside the controller. The other wire coming from the

master valve should be attached to the MV terminal inside

the controller. Tighten each terminal screw.

Valve Common Wire

Valve 1

Valve 2

Valve 3

Valve 4

Valve

Wires

Master Valves

Master Valve Wire

(Black Lead)

(Red Lead)

CONNECTING A WEATHER SENSOR

A Hunter weather sensor or other micro-switch-type

weather sensors can be connected to the controller. The

purpose of this sensor is to stop automatic watering when

weather conditions dictate. WRC (Wireless Rain-Clik®) is not

compatible with XC Hybrid.

1. Remove the metal jumper plate that is attached across the

two SEN terminals inside the controller.

2. Connect one wire to one SEN terminal and the other wire to

the other SEN terminal.

When the weather sensor has

deactivated automatic watering,

the OFF, and icon will appear on

the display.

Testing the Weather Sensor

The XC Hybrid provides simplied testing of

a rain sensor when the sensor is wired

into the sensor circuit. You can manually

test proper operation of the rain sensor by

running a MANUAL ALL STATIONS cycle

or by activating the system using the ONE

TOUCH MANUAL START (see page 15). During

the Manual cycle, pressing the test button on

the Mini-Clikwill interrupt watering.

Manually Bypassing the Weather Sensor

If the rain sensor is interrupting irrigation you can bypass it

by using the bypass switch on the front of the controller. Slide

the switch to the SENSOR BYPASS position to disable the rain

sensor from the system to allow for controller operation. You

can also bypass the weather sensor for manual operation by

using the MANUAL – ONE STATION function.

Mini-Clik Rain Sensor

/DAY

ACTIVE

BYPASS

Andere Handbücher für XC Hybrid

Inhaltsverzeichnis

Andere Hunter Bedienfeld Handbücher

Hunter

Hunter HPC Bedienungsanleitung

Beliebte Bedienfeld Handbücher anderer Marken

RDZ

RDZ PC-HRX Bedienungsanleitung

STG-BEIKIRCH

STG-BEIKIRCH MZ3 Technisches Handbuch

Efka

Efka Variocontrol V810 Bedienungsanleitung

Cebora

Cebora 208-10 Bedienungsanleitung

AMX

AMX AutoPatch CP-15 Bedienungsanleitung

Satel

Satel CA-6 KLED-S Bedienungsanleitung

Evolution

Evolution IQ plus 800 Bedienungsanleitung

Fagor

Fagor 8040 TCO CNC Bedienungsanleitung

AKO

AKO PROCool AKO-17635-2 Bedienungsanleitung

ABB

ABB 6136/30M-101 Bedienungsanleitung

Telikou

Telikou BK-603 Belt Pack Bedienungsanleitung

Mapei

Mapei Mapeheat Thermo Touch Bedienungsanleitung

Bosch

Bosch D9412GV4 Bedienungsanleitung

Mitsubishi Heavy Industries

Mitsubishi Heavy Industries SC-SL4-AE2/1 Bedienungsanleitung

Sminn

Sminn BOX L VF1L EI Bedienungsanleitung

Balboa

Balboa TP600 Bedienungsanleitung

Nice

Nice HSCU1 Technische Daten

Truma

Truma CP plus Bedienungsanleitung