Hunter Node Bedienungsanleitung

Battery-Operated Controller

Owner’s manual and programming instructions

NEW

ENG

TABLE OF CONTENTS

NODE FEATURES........................................2

NODE COMPONENTS ....................................3

Control Buttons

LCD Display

CONNECTING THE BATTERY/BATTERIES .....................4

ATTACHING SOLENOIDS..................................5

To Wire DC Solenoids to the NODE

To Mount the NODE to a Valve (Figure 1)

MOUNTING THE NODE...................................6

CONNECTING A WEATHER SENSOR ........................6

Setting the Date and Time

IDLE MODE ............................................7

RUN MODE ............................................7

PROGRAMMING ........................................7

Setting Watering Start Times

Setting the Run Times

Setting Watering Days

Selecting Odd/Even Days to Water

Selecting Interval Days to Water

Setting the Seasonal Adjustment

Turning the System Off

Manual Watering

Sensor Operation

ADVANCED PROGRAMMING FEATURES ....................12

Sensor Bypass

Easy Retrieve Memory

Setting Master Valve Operation (NODE-200, NODE-400,

& NODE-600 only)

Programmable Off (up to 99 days)

Hunter Quick Check

BATTERY LIFE INDICATOR ................................14

RESETTING CONTROLLER................................14

TROUBLESHOOTING GUIDE ..............................15

SPECIFICATIONS .......................................16

NOTES ...............................................17

ENG

NODE FEATURES

•Simple push button programming

•Single station model with DC latching solenoid. 2,4, or 6 station models also available (solenoids not included).

•Large Liquid Crystal Display (LCD) with easy to understand icons

•Operates on a standard 9-volt alkaline batteries (1 or 2 for extended battery life)

•3 programs (A, B, C) with up to 4 start times each

•Run times from 1 min to 6 hours

•Manual watering

•Battery Indicator shows remaining life of battery

•Rain sensor compatible

•Non-volatile memory retains all program information

•Seasonal Adjustment from 10–150%

•Easy Retrieve Memory allows saving/retrieval of preferred program data

•Manual Bypass of Rain Sensor

•Total Run Time Calculator shows total program irrigation time per program

ENG

NODE COMPONENTS

This section provides a brief overview of some of the components

of the NODE. Each item will be discussed in further detail later.

However, this section can be helpful in getting acquainted with the

different options available.

11 12 14 1315

3 1

Control Buttons

Button

– Increases the selected ashing display

Button

– Decreases the selected ashing display

Button

– Selects programming function

Button

– Advances the selected ashing display back to the

next item

Button

– Navigates the selected ashing display back to

the previous item

Button

– Selects the program (A, B, or C)

LCD Display

Main Display

– Indicates all program information

Station Number

– Indicates the station number being programmed

Start Time Number

– Indicates the start timer number being

programmed

Program

– Indicates the program (A, B, or C)

Current Time/Day

– Indicates when current day/time is

being set

Start Times

– Indicates when start times are being set

Run Times

– Indicates when Run Times are being set. Allows

user to set run times from 1 minute to 6 hours.

Watering Days

– Allows the user to select individual days to

water or a selected number of days between watering (interval)

Seasonal Adjustment

– Allows the seasonal adjustment to be

programmed form 10–150% (default value is 100%)

10.

System Off

– Indicates that watering is suspended

11.

Manual On/Off

– Indicates when manual watering is

programmed. Allows the user to activate the station manually.

12.

– Indicates that station one is set to master valve operation

(only available on 2,4, or 6 station models)

13.

Battery Status

– Indicates remaining battery life

14.

Umbrella

– Indicates the rain sensor is suspending irrigation

15.

Crossed Umbrella

– Indicates the rain sensor has been

manually bypassed

ENG

To Install the Battery/Batteries

1. Unscrew the rear body of the NODE body to gain access to

the battery compartment.

2. Insert the battery/batteries into the battery tray and connect to

the controller using the battery connector.

3. Make sure that no water is inside the battery compartment.

4. Screw the NODE rear body back onto the front half.

NOTE: Make sure that the seal marker on the

rear half of the NODE lines up with the front

half, ensuring that a proper seal is created.

The NODE uses two standard 9-volt batteries (not included) to

operate the valves and program the controller. The controller can

operate using either a single 9-volt battery or using two 9-volt

batteries. Under normal conditions, the expected life is 1 year for a

single battery and two years when using two 9-volt batteries.

NOTE: The NODE has non-volatile memory

which allows for the battery to be removed

without losing program information.

CONNECTING THE BATTERY/BATTERIES

Common Wire (Black Leads)

ENG

ATTACHING SOLENOIDS

The NODE-100 is provided with a solenoid attached to the

controller. The NODE-200, NODE-400, and NODE-600 multi-station

controllers will operate up to 2, 4, or 6 solenoids, respectively.

Hunter DC solenoids (P/N 458200) can easily be installed on all

Hunter Plastic Valves.

NOTE: Must use DC Latching Solenoids

operating between 9-11VDC. 24VAC Solenoids

will not operate with the NODE.

To Wire DC Solenoids to the NODE

1. Attach the black leads from each solenoid to the single

common wire (black lead) coming from the NODE. Secure all

wire connections with waterproof connectors.

2. Attach one red wire from each solenoid to the corresponding

station wire (red lead) from the NODE. The station numbers

are identied on the face of the NODE. Secure all wire

connections with waterproof connectors.

NOTE: The maximum wire distance between the

solenoid and NODE is 100 ft/30 m (18 gauge

minimum wire size).

Station Wire (Red Leads)

Mounting Clip

Figure 1 Hunter Model Mini-Clik®

The NODE can easily be mounted on any Hunter plastic valve.

A specially designed valve mounting clip makes installation a

snap. A protective rubber cover is provided to prevent dirt from

accumulating on the face of the NODE.

To Mount the NODE to a Valve (Figure 1)

1. Unscrew the existing solenoid from the valve.

2. Screw the Hunter DC latching solenoid (P/N 458200) into the

valve bonnet.

3. Attach the large end of the valve mounting clip to the middle

of the NODE body.

4. Snap the small end of the valve mounting clip to the solenoid.

A Hunter Mini-Clik®or Rain-Clik®rain sensor can be connected to

the NODE. The purpose of this sensor is to stop watering when

weather conditions dictate.

1. Cut the yellow wire loop attached to the NODE at

approximately the middle of the loop.

2. Remove approximately ½" (13 mm) of insulation from each

wire. Attach one yellow wire to each of the wires of the weather

sensor. You can mount the rain sensor up to 100 ft (30 m) from

the NODE controller (18AWG/1.0 mm minimum wire size).

3. Secure wire connections with waterproof connectors.

CONNECTING A WEATHER SENSOR

NOTE: When the Rain Sensor is interrupting the

watering, the display will show the System Off

icon , “OFF” and on the display.

MOUNTING THE NODE

ENG

IDLE MODE

RUN MODE

Normally the NODE display shows the time and day, day of the

week, MV (if master valve option is activated) and the battery life

indicator. During a short period of inactivity the display will shut off

to retain battery power. Pressing any button will wake up the NODE

to the Idle Mode.

When the controller is operating a program the items shown on the

display will include the station number, program letter, remaining

runtime, and the blinking Rotor icon.

The NODE uses standard Hunter controller programming with 3

programs (A, B, C) and 4 start times per program. On standard

Hunter controllers a dial is used to scroll between the programming

functions, however, on the NODE the button is used to quickly

and easily create the irrigation program. When programming, the

ashing portion of the display can be changed by pressing the

or buttons. To change something that is not ashing, press the

or buttons until the desired item is ashing.

Setting the Date and Time

1. Push the button until the icon is displayed.

2. All 4 digits will be displayed representing the year. Use the

or buttons to change the year. Press the button to

proceed to setting the month.

3. All 4 digits will be displayed with the two digits on the left

representing the month ashing. Use the or buttons to

change the month. Press the button to proceed to setting

the day.

4. Only the two digits on the right side will be displayed and

ashing, representing the day. Press the or button to

change the day. Press the button to proceed with changing

the hour. Press the button to proceed to setting the time.

5. The AM/PM/24 time setting is shown ashing. Press the or

button to change the time setting to AM, PM, or 24-hour

time. Press the button to proceed to setting the hour.

PROGRAMMING

ENG

6. All 4 numbers are shown with the two numbers on the left

ashing, representing the hour. Use the or buttons to

change the hour. Press the button to proceed to setting

the minutes.

7. All 4 numbers are shown with the two numbers on the right

ashing, representing the minutes. Use the or buttons

to change the minutes. Pressing the button will advance

to the year setting at step #2.

8. Press the button to proceed to the next programming

function or allow controller to return to idle mode.

Setting Watering Start Times

1. Press the button until the icon is displayed.

2. The start time will be displayed ashing, along with the

program letter (A, B, or C) and the start time number (1, 2, 3,

or 4) in the upper left of the display. Up to 4 different start

times can be set for each program.

3. Use the or buttons to change the start time for the

program that is displayed. Each press of the button will change

the start time in 15 minute increments.

4. Press the button to add an additional start time to the

program displayed. The start time number is shown in the

upper left corner of the display.

5. Press the button to add start times to a different program.

6. Press the button to proceed to the next programming

function or allow controller to return to idle mode.

NOTE: After programming the run time for the

last station press the button to display the

total run time for the program.

Setting the Run Times

1. Press the button until the icon is displayed.

2. The run time will be displayed ashing. Also shown is the

program letter (A, B, or C) and the active station # on the lower

left side of the display. Press the or button to change

the station run time from 1 minute to 6 hours.

3. Press the button to advance to the next station.

4. Press the button to add a run time to another program.

5. Press the button to proceed to the next programming

function or allow controller to return to idle mode.

PROGRAMMING (CONTINUED)

Inhaltsverzeichnis

Andere Hunter Controller Handbücher

Hunter

Hunter WVC Betriebsanleitung

Hunter

Hunter PRO-C PC Series Betriebsanleitung

Hunter

Hunter XC Betriebsanleitung

Hunter

Hunter EC Bedienungsanleitung

Hunter

Hunter Pro-C PCM-1600 Bedienungsanleitung

Hunter

Hunter 600-Z Bedienungsanleitung

Hunter

Hunter SRC Plus Installations- und Betriebshandbuch

Hunter

Hunter XC hybrid Betriebsanleitung

Hunter

Hunter Hydrawise HCC-800-PL Bedienungsanleitung

Hunter

Hunter ACC Bedienungsanleitung

Hunter

Hunter 99111 Bedienungsanleitung

Hunter

Hunter SpectraProbe XE Gebrauchsanweisung

Hunter

Hunter X-Core XC-801i-E Betriebsanleitung

Hunter

Hunter NODE-BT Bedienungsanleitung

Hunter

Hunter Eco-Logic 6 Betriebsanleitung

Hunter

Hunter Hydrawise Pro-HC Kurzanleitung

Hunter

Hunter Pro-C Betriebsanleitung

Hunter

Hunter Hydrawise HC-1200M Bedienungsanleitung

Hunter

Hunter Hydrawise HC-1200M Bedienungsanleitung

Hunter

Hunter Hydrawise Ready Bedienungsanleitung

Hunter

Hunter SVC-400 Bedienungsanleitung

Hunter

Hunter ICC2 Bedienungsanleitung

Hunter

Hunter SVC Bedienungsanleitung

Hunter

Hunter XC Hybrid Betriebsanleitung

Beliebte Controller Handbücher anderer Marken

Digiplex

Digiplex DGP-848 Betriebsanleitung

YASKAWA

YASKAWA SGM series Bedienungsanleitung

Sinope

Sinope Calypso RM3500ZB Bedienungsanleitung

Isimet

Isimet DLA Series Style 2 Installationshandbuch

LSIS

LSIS sv-ip5a Bedienungsanleitung

Rockwell Automation

Rockwell Automation 1769-L31 Bedienungsanleitung

Airflow

Airflow Uno hab Bedienungsanleitung

ABB

ABB ACS580-01 drives Bedienungsanleitung

Panasonic

Panasonic GM1 Series Bedienungsanleitung

Emerson

Emerson SW93 Bedienungsanleitung

AutoAqua

AutoAqua Smart ATO micro SATO-120P Bedienungsanleitung

Panasonic

Panasonic FP? Positioning Unit RTEX Bedienungsanleitung

Samson

Samson Type 5824 Service-Handbuch

Alpha IP

Alpha IP MIOB 21001 Bedienungsanleitung

Siemens

Siemens OpenAir GMA 1 Series Bedienungsanleitung

Surecom

Surecom SR-629 Bedienungsanleitung

Fishman

Fishman TriplePlay Bedienungsanleitung

Regulus

Regulus SRS1 T Bedienungsanleitung