Hunter 41457-01 Bedienungsanleitung

41457-01 7/2000

Installation and Operation Manual

For Hunter Ceiling Fans

41457-01 7/2000

SINCE 1886

241457-01 7/2000

41457-01 7/2000

CONGRATULATIONS!

Your new Hunter ceiling fan is an

addition to your home or office that

will provide comfort and perfor-

mance for many years. This manual

gives you complete instructions for

installing and operating your fan.

We are proud of our work. We ap-

preciate the opportunity to supply

you with the best ceiling fan avail-

able anywhere in the world.

Before installing your fan, record the

following information for your

records and warranty assistance.

Please refer to the carton and the

Hunter nameplate (located on top

outside fan motor housing) for the

proper information.

7/2000

Model Name __________________

Catalog No. ___________________

Serial No. _____________________

Date Purchased ________________

Where Purchased ______________

_____________________________

Please attach your Hardware Sheet

and Exploded View Sheet to this

manual for future reference.

Attach Your Receipt

or a Copy of

Your Receipt Here

441457-01 7/2000

CONTENTS

Important Information....................................................................................................................................... 5

Step 1 - Getting Ready ...................................................................................................................................... 6

Step 2 - Installing the Ceiling Plate.................................................................................................................... 8

Step 3 - Assembling Pipe/Ball Assembly........................................................................................................... 10

Step 4 - Assembling the Fan............................................................................................................................ 12

Step 5 - Hanging the Fan ................................................................................................................................ 14

Step 6 - Installing the Remote ......................................................................................................................... 15

Step 7 - Wiring the Fan ................................................................................................................................... 18

Step 8 - Attaching the Canopy........................................................................................................................ 20

Step 9 - Assembling Fan Blades....................................................................................................................... 21

Step 10 - Attaching the Switch Housing.......................................................................................................... 23

Step 11 - Installing Light Fixture ...................................................................................................................... 26

Operating Your Hunter Fan and Remote ......................................................................................................... 30

Cleaning and Maintenance ............................................................................................................................. 32

Troubleshooting .............................................................................................................................................. 33

41457-01 7/2000

IMPORTANT INFORMATION

not lock the circuit break-

ers in the off position, se-

curely fasten a prominent

warning device, such as a

tag, to the service panel.

• All wiring must be in accor-

dance with national and lo-

cal electrical codes and

ANSI/NFPA 70. If you are

unfamiliar with wiring, you

should use a qualified elec-

trician.

• To reduce the risk of per-

sonal injury, do not bend

the blade attachment sys-

tem when installing, bal-

ancing, or cleaning the fan.

Never insert foreign objects

between rotating fan

blades.

DO YOU NEED HELP?

To install a ceiling fan, be sure you

can do the following:

• Locate ceiling joist or other suit-

able support in ceiling.

• Drill holes for and install wood

screws.

• Identify and connect electrical

wires.

• Lift 40 pounds.

If you need help installing the fan,

yourHunter fandealer candirectyou

to a licensed installer or electrician.

• To reduce the risk of fire,

electrical shock, or motor

damage, do not use a solid-

state speed control with

this fan. Use only Hunter

speed controls.

WARNINGS

• To avoid possible electrical

shock, before installing

your fan, disconnect the

power by turning off the

circuit breakers to the out-

let box and associated wall

switch location. If you can-

CAUTIONS

• Read entire booklet care-

fully before beginning in-

stallation and save these

instructions.

• To reduce the risk of per-

sonal injury, attach the fan

directly to the support

structure of the building ac-

cording to these instruc-

tions, and use only the

hardware supplied.

641457-01 7/2000

GATHERING THE TOOLS

You will need the following tools for

installing the fan:

• Electric drill with 9/64" bit

• Standard screwdriver

• Phillips-head screwdriver

• Wrench or pliers

OPTIONAL ACCESSORIES

Consider using Hunter’s optional ac-

cessories, including a wall-mounted

orremotespeedcontrol.Toinstall and

usethe accessories, followthe instruc-

tions included with each product.

For quiet and optimum performance

of your Hunter fan, use only Hunter

speed controls.

STEP 1 - GETTING READY

PREPARING THE FAN SITE

Thelocation of aceiling fanand how

the fan is attached to the building

structure are essential for reliable

operation, maximum efficiency, and

energy savings. For this reason, we

have included a separate booklet —

“Guide to Choosing and Preparing

a Ceiling Fan Site” — to help you

select the best location for your fan.

The booklet also provides informa-

tion to ensure your fan support and

electricoutlet boxmeet UL-approved

safety codes for ceiling fans.

The instructions in this installation

manual assume that you have used

“Guide to Choosing and Preparing

a Ceiling Fan Site” to pick the fan

locationand makecertainthe proper

fan support and outlet box are in-

stalled.

CHECKING YOUR FAN PARTS

Carefully unpack your fan to avoid

damage to the fan parts. Check for

any shipping damage to the motor

orfan blades.If oneof thefan blades

was damaged in shipment, return all

the blades for replacement.

Hint: If you are installing more than

one fan, keep the fan blades

in sets, as they were shipped.

The fan includes a separate diagram

of the screws and other small parts

needed for the fan. Keep this dia-

gramhandy foridentifying parts dur-

inginstallation; thediagramindicates

the step in which each part is used.

If any parts are missing or damaged,

contact your Hunter dealer or call

Hunter Parts Department at

901-248-2222.

41457-01 7/2000

INSTALLER’S CHOICE®

This patented 3-position mounting

systemprovidesyoumaximum instal-

lation flexibility and ease. You can

installyour Hunterfan in oneof three

ways. The steps in this manual in-

cludespecific instructions forthe fan

mountingmethod ofyourchoice. For

a ceiling 8 feet or higher, standard

mounting is recommended.

Flush Mounting (Figure 1a) fits

close to the ceiling, for low ceilings

less than 8 feet high.

Standard Mounting (Figure 1b)

hangs from the ceiling by a connec-

torpipe (included), forceilings 8 feet

or higher. For ceilings higher than

eight feet, you can purchase Hunter

extension rods. All Hunter fans use

sturdy 3/4" diameter pipe to assure

stability and wobble-free perfor-

mance.

Angle Mounting (Figure 1c) hangs

from a vaulted or angled ceiling.

Figure 1c - Angle Mounting

Figure 1b - Standard Mounting

Figure 1a - Flush Mounting

10"

12"

34°Max

Pitch

841457-01 7/2000

STEP 2 - INSTALLING THE CEILING PLATE

4. Align the slotted holes in the ceil-

ing plate with the pilot holes in

the wood support structure.

Note: The isolation pads should

be flush against the ceiling.

1. Drill twopilotholes intothe wood

support structure through the

outermost holes on the outlet

box. The pilot holes should be

9/64" in diameter by 2 3/4" in

depth.

2. Bring the lead wires around the

sidesof the ceilingplate. Thread-

ing the lead wires through the

hole in the middle may cause

problems when installing the re-

mote and trying to close the

canopy.

3. Your fan comes with two neo-

prenenoise isolators.Position the

isolatorsbetween theceilingplate

and ceiling by inserting the raised

areas on each isolator into the

holes in the ceiling plate. Refer to

Figure 2a.

Figure 2a - Adding Isolators to Ceiling

Plate Figure 2b - Correct Position of Ceiling

Plate for Angle Mounting

Ceiling Plate

Hooks

Isolators

Ceiling

Plate

For Angle Mounting Only: Be

sure to orient the ceiling plate so

that the two hooks point up to-

wards the ceiling peak as shown

in Figure 2b. Note: You will use

the hooks to support the fan

while wiring the fan.

41457-01 7/2000

Figure 2c - Attaching Ceiling Plate to

2 x 4 Brace

Ceiling Joist

Ceiling

Outlet Box

Ceiling

Plate

Flat

Washer 3" Wood

Screw

5. Placea flat washeron each ofthe

two 3" screws and pass the

screws through the slotted holes

in the ceiling plate as shown in

Figure 2c.

6. Tightenthe screwsinto the9/64"

pilot holes; do not use lubricants

on the screws. Do not over-

tighten.

10 41457-01 7/2000

continued

As discussed in STEP 1 - GETTING

READY, your Hunter fan can be in-

stalled in a standard mounting posi-

tion.

Included with the fan are two pipes:

one 3" long pipe/ball assembly for

standard mounting on 8' ceilings and

one 12" long pipe for 9' ceilings and

higher. See Figure 3a.

If you are going to install the fan us-

ing the standard mounting, go to

STEP 4 - ASSEMBLING THE FAN.

If you are going to install the fan us-

ing the 12" long pipe for 9' ceilings

or higher, complete the steps below.

STEP 3 - ASSEMBLING PIPE/BALL ASSEMBLY

3. Remove the ball from the pipe.

4. Remove the pin from the pipe.

Figure 3a - Pipes

Figure 3b - Removing ball assem-

bly

REMOVING BALL ASSEMBLY

For the following steps refer to

Figures 3b and 3c.

1. Locate the 3" pipe/ball assembly.

2. Remove the positioning screw

from the top of the ball.

NOTE: The ball will become

loose and should slide down the

pipe.

3" Pipe/Ball

Assembly

12" Pipe

Positioning Screw

Leadwire

Assembly

Ball

Ground

Screw

Inhaltsverzeichnis

Andere Hunter Lüfter Handbücher

Hunter

Hunter Ristrello 50188 Bedienungsanleitung

Hunter

Hunter Hunter Ceiling Fan Bedienungsanleitung

Hunter

Hunter 27048 Konfigurationshandbuch

Hunter

Hunter Avia II Bedienungsanleitung

Hunter

Hunter ECO 14 Bedienungsanleitung

Hunter

Hunter 41462-01 Bedienungsanleitung

Hunter

Hunter 28682 Bedienungsanleitung

Hunter

Hunter 23298 Gebrauchsanweisung

Hunter

Hunter 20552 Bedienungsanleitung

Hunter

Hunter Webster Bedienungsanleitung

Hunter

Hunter Millington 51667 Bedienungsanleitung

Hunter

Hunter Burleson Bedienungsanleitung

Hunter

Hunter Captiva 21318 Handbuch

Hunter

Hunter 51384 Bedienungsanleitung

Hunter

Hunter 25517 Handbuch

Hunter

Hunter 21315 Bedienungsanleitung

Hunter

Hunter 21728 Bedienungsanleitung

Hunter

Hunter Altitude Gebrauchsanweisung

Hunter

Hunter Sona Bedienungsanleitung

Hunter

Hunter Type 5 Models Gebrauchsanweisung

Hunter

Hunter Savoy Bedienungsanleitung

Hunter

Hunter Vancouver 21328 Bedienungsanleitung

Hunter

Hunter 52486 Bedienungsanleitung

Hunter

Hunter 42637-01 Gebrauchsanweisung

Beliebte Lüfter Handbücher anderer Marken

ELTA FANS

ELTA FANS H03VV-F Bedienungsanleitung

Emerson

Emerson CARRERA VERANDA CF542ORB00 Bedienungsanleitung

Panasonic

Panasonic FV-15NLFS1 Bedienungsanleitung

Kompernass

Kompernass KH 1150 Bedienungsanleitung

VES

VES FALA100/12V/TR Bedienungsanleitung

Vertiv

Vertiv Liebert DCD Bedienungsanleitung

Westinghouse

Westinghouse GFP Series Bedienungsanleitung

Venmar

Venmar KUBIX HRV PLUS Series Bedienungsanleitung

Maico

Maico ECR 31 Bedienungsanleitung

Sonnenkonig

Sonnenkonig Dinky Bedienungsanleitung

S&P

S&P ECOWATT HXBR Bedienungsanleitung

Wider

Wider IMP03369BH Bedienungsanleitung

Panasonic

Panasonic F-60DHN Bedienungsanleitung

Hinkley

Hinkley HIGHLAND Bedienungsanleitung

Broan

Broan 766BN Bedienungsanleitung

Premium

Premium PFS16022 Montageanleitung

Litex Industries

Litex Industries E-CGL52CB5C1 Bedienungsanleitung

Lindab

Lindab LTDF Bedienungsanleitung