Hunter Bullet Spotlight Kit Gebrauchsanweisung

Form# 43551-01

20090420

English Español

Bullet Spotlight KitBullet Spotlight KitBullet Spotlight Kit

Owner’s Guide and Installation Manual

Manual De Propietario

43551-01 • 04/20/09 • Hunter Fan Company

Table Of Contents

Installing the Light Kit on Fans With

Removable Switch Housing ........4

Installing the Light Kit on Fans With

Non-Removable Switch Housing...6

Installing the Light Kit on the Hunter

Original .........................8

Troubleshooting.......................9

Your new Hunter® light kit is an addition to your home or oce that

will provide comfort and performance for many years. is installation

and operation manual gives you complete instructions for installing

and operating your light kit.

We are proud of our work. We appreciate the opportunity to supply

you with the best products available anywhere in the world.

Before installing your light kit, for your records and warranty assistance,

record information from the carton and Hunter nameplate label.

Cautions and Warnings

•READ THIS ENTIRE MANUAL CAREFULLY BEFORE BEGINNING

INSTALLATION. SAVE THESE INSTRUCTIONS.

• Use only Hunter replacement parts.

• To reduce the risk of personal injury, install this light xture only on

Hunter® fan types A through Z. Note: e fan type can be found on

the ceiling fan package or on the nameplate label located on top of

the motor housing of the ceiling fan.

• To avoid possible electrical shock, before installing light xtures,

disconnect the power by turning o the circuit breakers both to

the outlet box and to its associated wall switch location. If you

cannot lock the circuit breakers in the o position, securely fasten a

prominent warning device, such as a tag, to the service panel.

• Connect house wiring to the fan before attaching the light xture to

the fan.

• All wiring must be in accordance with national and local electrical

codes and ANSI/NFPA 70. If you are unfamiliar with wiring, use a

qualied electrician.

Welcome

43551-01 • 04/20/09 • Hunter Fan Company

Installation Methods of Hunter® Ceiling Fans Type A-Z

Removable Switch Housing

Non-removable Switch Housing

e Hunter Original

Your ® light kit can be installed in one of three

ways, depending on the type of switch housing. e steps

in this manual include instructions for all three installation

methods: Fans with removeable switch housings, fans

with non-removeable switch housings, and

Hunter Originals.

Preparing the Light Kit.

1. Disconnect power by turning o the circuit breakers

both to the outlet box and to its associated wall switch

location.

2. Loosen or remove the three screws on the top of the

light kit tter. Twist the tter clockwise and loosen it

from the light kit.

Screws

Light Kit

Fitter

43551-01 • 04/20/09 • Hunter Fan Company

1. Unscrew the three screws from the upper switch housing. Disconnect

the 9-pin plug connectors. Remove the lower switch housing.

2. Push the plug button from inside the lower switch housing to remove

the plug button and switch housing cap.

NOTE: Save the plug button and switch housing cap should you

choose to remove the light xture in the future.

To attach the light kit tter, partially install two #6-32 screws

and the

lock washers on the red tag

into the switch housing.

4. Align the keyhole slots in the light kit tter with the #6-32 screws.

5. Turn the housing counterclockwise until the housing assembly screws

are rmly situated in the narrow end of the keyhole slots. Tighten

screws rmly.

6. Feed the two wires from the light xture through the center hole in

the lower switch housing.

7. To secure the light kit tter, thread the nut and washer onto the rod

from the light kit. Tighten the nut and washer you previously threaded

onto the rod from the light kit.

Removable Switch Housing

9-Pin Plug

Connector

Lower Switch

Housing

Plug Button

Screw

Steps 1-2

WARNING: Improper installation could cause the light xture to fall.

Light Kit

Fitter

Washer

Threaded

Rod

Switch

Housing

Nut

#6-32

Screw

Steps 3-5

Step 7

Installing the Light Kit on Fans With Removable Switch Housings

43551-01 • 04/20/09 • Hunter Fan Company

Installing the Light Kit on Fans With Removable Switch Housings (Continued)

8. Remove the wire connectors from the two wires in the switch housing

labeled “Connect Light Here” or “For Light Use.”

To connect the wires, hold the bare metal leads together and place a

wire connector over them, then twist the wire connector clockwise until

tight.

Connect the black wire with a white stripe from the switch housing to

the black wire from the light kit. Connect the white wire from the switch

housing to the white wire from the light kit. Secure all wire connections

using wire connectors.

CAUTION: Be sure no bare metal wires or wire strands are visible after

making the connections.

9. Finish attaching the light kit to the lower switch housing. Align the

notches in the sides of the light kit with the screws on the tter. Twist

the light kit counterclockwise to lock the screws in place. Tighten the

screws securely.

10. Reconnect the 9-pin plug connector.

11. Reinstall screws to reattach the lower switch housing to the upper

switch housing.

12. Install the included CFL bulbs.

13. e installation is complete and you can restore power to the ceiling fan

Wire

Connections

Step 8

Step 9

Plug

Connector

Lower Switch

Housing

Assembly Screw

Plug

Connector

Detail

Steps 10-11

CFL

(included)

Light Kit

Light Kit Fitter

43551-01 • 04/20/09 • Hunter Fan Company

1. Uninstall the two attachment screws from the switch housing cover.

2. Remove the plug or screw from the center of the switch housing cover.

NOTE: Save the plug button and switch housing cap should you choose to

remove the light xture in the future.

3. read the switch housing cover onto the light kit tter. Align the screw

holes in the light kit tter with the screw holes in the switch housing cover.

4. Install the nut and washer onto the threaded rod from the light kit tter to

secure the switch housing cover.

5. Remove the wire connectors from the two wires in the switch housing

labeled “Connect Light Here” or “For Light Use.” One wire is white and the

other wire is black with a white stripe.

6. Feed the two wires from the switch housing through the threaded rod in

the light kit tter.

7. Use the two attachment screws removed from the lower switch housing

and the lock washers on the red tag of the light kit tter. Install the screws

into the light kit and the housing. Securely tighten the two screws.

Switch

Housing

Cover

Plug

Attachment

Screw

Non-Removable Switch

Housing

Steps 1-2

WARNING: Improper installation could cause the light xture to

fall, or result in electrical shock or personal injury.

Nut

Washer

Screw

Hole

Switch

Housing

Cover

Light Kit Fitter

Steps 3-7

Attachment

Screw

Wire

Connectors Step 5

Installing the Light Kit on Fans With Non-Removable Switch Housing

43551-01 • 04/20/09 • Hunter Fan Company

Installing the Light Kit on Fans With Non-Removable Switch Housing Cont.

8. To connect the wires, hold the bare metal leads together and place a wire

connector over them, then twist the wire connector clockwise until tight.

Connect the black wire with a white stripe from the switch housing to

the black wire from the light kit. Connect the white wire from the switch

housing to the white wire from the light kit. Secure all wire connections

using wire connectors.

CAUTION: Be sure no bare metal wires or wire strands are visible after making

the connections.

9. Finish attaching the light kit to the lower switch housing. Align the

notches in the sides of the light kit with the screws on the tter. Finish

attaching the light kit to the lower switch housing. Align the notches

in the sides of the light kit with the screws on the tter. Twist the tter

counterclockwise to lock the screws in place. Tighten the screws securely.

10. Install the included CFL bulbs.

11. e installation is complete and you can restore power to the ceiling fan.

Wires

and Wire

connectors

Step 8

Step 9

CFL

(included)

Light Kit

Light Kit Fitter

43551-01 • 04/20/09 • Hunter Fan Company

Switch

Housing

Plate

Screw

Attachment

Screws

Light Kit

Fitter

Step 1

Steps 2-4

Wire

Connectors

Step 5

Step 6

1. Uninstall the two attachment screws from the switch housing cover.

NOTE: Save the switch housing cover should you choose to remove the

light xture in the future.

2. Remove the wire connectors from the two wires in the switch housing

labeled “Connect Light Here” or “For Light Use.” One wire is white and the

other wire is black with a white stripe.

3. Feed the two wires from the switch housing through the threaded rod in

the light kit tter.

4. Use the two attachment screws removed from the lower switch housing

and the lock washers on the red tag of the light kit tter. Partially install the

screws in the switch housing. Install the screws into the light kit and the

housing.Rotate the housing counterclockwise until the screws are locked

into the narrow ends of the keyhole slots. Securely tighten the two screws.

5. To connect the wires, hold the bare metal leads together and place a wire

connector over them, then twist the wire connector clockwise until tight.

Connect the black wire with a white stripe from the switch housing to

the black wire from the light kit. Connect the white wire from the switch

housing to the white wire from the light kit. Secure all wire connections

using wire connectors.

CAUTION: Be sure no bare metal wires or wire strands are visible after making

the connections.

6. Finish attaching the light kit to the lower switch housing. Align the notches

in the sides of the light kit with the screws on the tter. Twist the tter

counterclockwise to lock the screws in place. Tighten the screws securely.

7. Install the included CFL bulbs.

8. e installation is complete and you can restore power to the ceiling fan.

CFL

(included)

Light Kit

Light Kit Fitter

Installing the Light Kit on the Hunter Original

43551-01 • 04/20/09 • Hunter Fan Company

Troubleshooting

Light does not come on.

1. Make sure bulbs are installed properly.

2. Make sure breakers or fuses are on.

3. Verify that the light power lead is connected at the ceiling. Refer to

your ceiling fan manual for locating assembly and wiring.

If you need parts or service assistance, please call

888-830-1326 or visit us at our Web site at

http://www.hunterfan.com.

Hunter Fan Company

7130 Goodlett Farms Pkwy. # 400

Memphis, Tennessee 38016

is Light Fixture Weighs 4 lbs. Printed in China

Troubleshooting

Inhaltsverzeichnis

Andere Hunter Wohnraumbeleuchtung Handbücher

Hunter

Hunter MM288PU Betriebsanleitung

Hunter

Hunter Marine II Gebrauchsanweisung

Hunter

Hunter Casbah Light Kit Bedienungsanleitung

Hunter

Hunter Dual Function Bowl Light Kit Gebrauchsanweisung

Hunter

Hunter Floating Glass Light Kit Bedienungsanleitung

Hunter

Hunter 10” Bedienungsanleitung

Hunter

Hunter Tea Stain Bowl Light Kit Bedienungsanleitung

Hunter

Hunter Tribeca Light Kit Tribeca Light Kit Gebrauchsanweisung

Beliebte Wohnraumbeleuchtung Handbücher anderer Marken

JONATHAN Y

JONATHAN Y JYL5019A Bedienungsanleitung

JONATHAN Y

JONATHAN Y JYL6007A Bedienungsanleitung

Philips

Philips Ledino 31606/11/16 Bedienungsanleitung

Salus

Salus UG600 Bedienungsanleitung

Safavieh Lighting

Safavieh Lighting CANDRI TBL4427A Bedienungsanleitung

Philips

Philips 405441213 Bedienungsanleitung

Philips

Philips Halogen Light Bedienungsanleitung

Pentair

Pentair GLOBRITE Bedienungsanleitung

Philips

Philips 55592-30-16 Bedienungsanleitung

Livoo

Livoo Night light Bedienungsanleitung

Schwaiger

Schwaiger NFL45 Bedienungsanleitung

FRITZ HANSEN

FRITZ HANSEN AQ01 PLUG-IN Bedienungsanleitung

MOOD

MOOD CORSIN JY-16 Bedienungsanleitung

Safavieh Lighting

Safavieh Lighting KREMP TBL4409A Bedienungsanleitung

JONATHAN Y

JONATHAN Y JYL8019 Bedienungsanleitung

XTRASUN

XTRASUN XTDEOKT1 Bedienungsanleitung

Inspire

Inspire Lana YF3306-M Wartungshandbuch

Triarch

Triarch Indoor Lighting 31550/1 Bedienungsanleitung