Hunter 44127 Bedienungsanleitung
Owner’s Manual
Models
44127
44132
44133
44134
Form# 44067-01
20120803
©2012 Hunter Fan Co.
English
5-2 Programmable
Weekdays-Weekends
INSTALLATION
5 MINUTE
44067-01 • 08/03/2012
2
Table of Contents
At A Glance
Know Your ermostat � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � �3
Setup
Setting Day and Time � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 10
Scheduling
Scheduling Introduction � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 12
Setting Your Schedule� � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 14
Temporary Temperature Change� � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 18
Turning Off Scheduling � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 20
Save Away��������������������������������������������������������������22
Features
Alerts ������������������������������������������������������������������24
Menu Options ���������������������������������������������������������26
Additional Features ����������������������������������������������������30
ermostat Assistance
Troubleshooting and Support� � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 31
Technical Support������������������������������������������������������33
Warranty
1 Year Guarantee�������������������������������������������������������34
©2012 Hunter Fan Company 3
Your thermostat has been pre-programmed from the factory with no programming
necessary. We recommend using these pre-programmed settings for a few days
before altering them as they offer maximum energy saving benets. If you do
decide to alter your programs, use the charts on page 13 to write out your
scheduled times and temperatures. After you have recorded your preferences,
follow the instructions on page 14 to alter your temperature settings.
There is no need to program the thermostat at the wall where it is mounted!
Remove the thermostat from the backplate by gripping the sides rmly and
pulling it straight off. This allows you to program the thermostat in comfort.
After you have programmed your thermostat, no other setting changes are
necessary unless you wish to browse through the menu to see how you may
further adjust the independent settings of your thermostat to meet your lifestyle.
The features section starting on page 26 of this manual will describe these
settings. Most settings have been preset for optimal performance.
If you need any assistance with installation or setup of your
new Hunter Thermostat, please call us, our technical support
staff is ready to help!
USA: 1-888-830-1326
Canada: 1-866-268-1936
Hours of operation are from 7:00 am to 7:00 pm Monday - Friday and 8:00 am
to 5:00 pm on Saturday, Central Time. You may also contact us over the Internet
at:
www.HunterFan.com
Know Your ermostat
44067-01 • 08/03/2012
4
1. Enters Schedule Setup for altering scheduled programs.
2. Sets the Save Away feature for when you will not be home during a regularly
programmed time.
3. Conrms completion of an action or returns you to the Home screen.
4. Allows access to the advanced features of the thermostat.
5. Moves you forward or backward while setting up features or schedules.
6. Adjusts time and temperature settings as well as moving up or down menu
lists.
7. Indicates whether the system is set to Heat, Cool, or Off.
8. Shows if the fan is set to Auto or On modes.
9. Allows you to switch between Heat, Cool, and Off modes.
10. Allows you to switch between fan Auto and On modes.
Know Your ermostat
Your Hunter programable thermostat:
©2012 Hunter Fan Company 5
Know Your ermostat
1
8
5
43
2
7
6
5
910
44067-01 • 08/03/2012
6
1. Holds 2 “AA” Batteries.
2. HE/HG Switch - allows you to set your furnace to Gas/Oil or Electric, based
on the type of system you have.
3. Allows your thermostat to operate your HVAC system* properly by indicating
the system type that you have.
*Conventional System: Uses a condensing unit for cooling and a
separate furnace system for heating.
*Heat Pump System: Uses the condensing unit for both heating and
cooling.
NOTE: If you are unsure of your system type it may be necessary to
contact our technical support department at 1-888-830-1326, your HVAC
manufacturer, or a local HVAC technician to determine this. Improper
selection of your system type could cause the thermostat to not operate your
system properly.
Know Your ermostat
©2012 Hunter Fan Company 7
1
3
2
Know Your ermostat
44067-01 • 08/03/2012
8
1. Shows the current day of the week or weekend.
2. Indicates the thermostat is running in schedule mode.
3. Indicates the current room temperature.
4. C will display when in Celsius mode. Nothing will display when set
to Fahrenheit.
5. Flashes when the furnace lter should be checked for replacement.
6. On when the current schedule period is running.
7. Indicates the current active schedule period.
8. Low battery warning, replace the batteries in the thermostat.
9. Indicates the fan is running when displayed.
10. Shows the current mode of the fan, Auto or On.
11. Indicates the current time in am(A) or pm (P).
12. On when the current operating mode, heat or cool, is running.
13. Current operating mode, heat or cool.
14. Indicates the thermostat is running in save away mode.
15. Current Set temperature the thermostat is scheduled to run.
Know Your ermostat
©2012 Hunter Fan Company 9
Know Your ermostat
70
o
Wed
Auto
Filter
10:05
P
o
72
At Home
Heat to
C
2
1
3
45
6
7
8
9
10
11
12
13
14
15
44067-01 • 08/03/2012
10
Setting Day and Time
Once you install the batteries, the thermostat will prompt you to set the
current day and time.
1. You will notice that “Mon” will be ashing at the top left of your screen.
Use the or buttons to move to your current day of the week and
press the Next button to advance to the next step.
2. Use the or button to change between am(A) and pm(P). Choose
Next to advance.
3. Next you will select your current hour by using the or buttons. The
Next button advances you to the next step.
4. Set your minutes using the or and press Done/
Home to nish or Back if you
need to make a correction to a previous step.
5. When nished, the thermostat will show “Updated!” to conrm your
settings are saved.
6. Your thermostat will next prompt you to set your programming, see page
14 step 2 if you wish to alter your programs at this time.
Andere Handbücher für 44127
1
Dieses Handbuch passt für folgende Modelle
3
Inhaltsverzeichnis
Andere Hunter Thermostat Handbücher
Hunter
Hunter Internet Thermostat Montageanleitung
Hunter
Hunter 44668 Bedienungsanleitung
Hunter
Hunter 42710-01 Bedienungsanleitung
Hunter
Hunter Energy Monitor 44408 Bedienungsanleitung
Hunter
Hunter Energy Monitor AC 42205 Bedienungsanleitung
Hunter
Hunter 44110 Bedienungsanleitung
Hunter
Hunter 47132 Bedienungsanleitung
Hunter
Hunter JustRight Bedienungsanleitung
Hunter
Hunter F42213 Bedienungsanleitung
Hunter
Hunter 44110B Bedienungsanleitung
Hunter
Hunter 44127 Montageanleitung
Hunter
Hunter Enermy Monitor IIPlus 44407 Bedienungsanleitung
Hunter
Hunter Internet Thermostat Bedienungsanleitung
Hunter
Hunter 40080 Bedienungsanleitung
Hunter
Hunter 44156 Bedienungsanleitung
Hunter
Hunter 42202 Bedienungsanleitung
Hunter
Hunter 43058 Bedienungsanleitung
Hunter
Hunter 44660 Bedienungsanleitung
Hunter
Hunter 44377 Benutzerhandbuch
Hunter
Hunter 44132 Bedienungsanleitung
Beliebte Thermostat Handbücher anderer Marken
EWELLY
EWELLY EW-181 Bedienungsanleitung
Prolon
Prolon T1100 Montageanleitung
Computherm
Computherm Q20 Bedienungsanleitung
Heatmiser
Heatmiser neoStat Bedienungsanleitung
Aube Technologies
Aube Technologies TH111GFCI-NP 240 VCA Bedienungsanleitung
Mars
Mars HEAT CONTROLLER IR Wireless Thermostat Bedienungsanleitung
