Husky MR481886W6B Bedienungsanleitung

Model MR481886W6B

(48"w x 18"d x 86"h)

Safety & General Instructions

This unit should be placed on a level surface and should be

securely anchored to a wall or floor with suitable fasteners,

which are not included. Failure to do so can result in a

possible safety hazard. Do not use this unit for anything

other than the manufacturer’s intended purpose. DO NOT

STAND ON ANY PART OF THE UNIT OR USE AS A LADDER.

Use care when working with metal parts, wear gloves.

Evenly distribute the weight on each level and always keep

the heavier loads on the bottom.

The unit is assembled one level at a time. Each level is

assembled with two beams (b) and two braces (c) connected to

the posts (a) and one wire shelf (d). Assembly is done by fitting

the rivets of the beams and braces into the slots of the posts.

A rubber mallet should be used on the ledge of the beams and

braces to properly seat the rivets into the tapered ends of the

post slots. After assembly re-check each beam and brace for

engagement. The wire deck will rest on the ledge surface of the

beam or brace depending upon the orientation of the shelf level.

Retain this manual for future use.

Components

B: beam (long) C: brace (short)

A: post

D: wire shelf

Description Component Nominal

Size

Quantity

A. post URPS43-BLK 43” 8

B. beam TRBM48-BLK 48” 12

C. brace TRBR18-BLK 18” 12

D. wire shelf 1848W 18” x 48” 6

E. post coupler CPOUT-BLK -- 4

F. post cap RL-PC-B1 -- 4

G. post foot FP-HP -- 4

PARTS LIST

Recommended Items for Assembly

E: post

coupler

F: post

cap G: post

foot

Rubber Mallet (preferred) or Hammer (protect surface with cloth

or wood block) and Gloves

Warranty

Shouldyouhavequestions,problems,damageormissingparts,contactusforassistance:

Chat:www.edsal.com/chatorwww.edsal.com/contact

Email:support@edsal.com

Phone:773‐475‐3131

Toobtainreplacementpartspleaseprovide:ModelNumber,PartNumber&Description,LocationPurchased,andDatePurchased

Manufacturer:

EdsalManufacturingCompany

Chicago,IL60609

AssembledinU.S.withglobalanddomesticcomponents



USPatents&PatentsPending





Rev:C061518

GUARANTEED FOREVER. If your Husky tool or storage unit

ever fails bring it back and we will replace it for free. This full

warranty gives you specific rights which vary from state to state.

If this product is defective contact the manufacturer for repair or

replacement parts.

Assembly Instructions - MR481886W6B

STEP 1 … assemble post feet to post

• Check that each post is in the proper orientation. The post should be

positioned so that the tapered end of the hole is pointing downward.

• Place post foot on the bottom of each for the four lower posts.

STEP 2 … assemble bottom level

• Assemble one brace to two lower posts skipping one hole from

the bottom of each post. Be sure the longer ledge of brace is on top.

• Place the rivets into the posts, and tap lightly to seat the rivets.

• Repeat this with the other two lower posts and brace.

• Assemble the two beams into the two post and brace assemblies by

placing the rivets into the post. Tap lightly to seat the rivets. Be sure

the longer ledge of the beam on top.

• Place a wire shelf on the ledge of the assembled beams and

braces with the flat side facing upwards.

STEP 3 … assemble next two levels

• Connect another two braces and two beams to the posts for the next level.

• Check that each beam and brace is spaced equally.

• Place a wire shelf on the ledge of the assembled beams and braces for

each level with the flat side of the wire shelf upwards.

• Repeat for third level.

STEP 4 … connect posts with couplers

• Position the couplers on the top edge of each bottom post.

• Tap the couplers down to the mid-point of the coupler.

• Position another post into the top half of the coupler and tap down until the

two posts connect fully into the coupler.

STEP 5 … assemble the remaining three levels

• Connect additional braces and beams to the posts for each level.

• Check that each beam and brace is level and properly spaced.

• Place a wire shelf on the ledge of the assembled beams and braces for

each level with the flat side of the wire shelf upwards.

STEP 6 … assemble the post caps

• Place and fasten the post caps to the top of each post.

STEP 7 … final check

• Check each beam and brace connection to be sure that the rivets are

properly seated.

ALTERNATE HORIZONTAL CONFIGURATION ...

• Shelf can be split into two units and used side by side. Post couplers are not required for this configuration.

• Beams and braces should be positioned in the top and bottom two post holes of each section for stability.

• Follow steps 2, 3 and 7

NOTE: Additional post caps (F) and post feet (G) are not included for this alternate configuration, but may be

purchased by contacting customer service - see contact information below. Order quantity of 4 each of (F)

and (G) and follow steps 1 and 6 when order is received.

Wire Shelf

Beam

Brace

Post

Alternate horizontal

configuration

Tap lightly

Beam/Brace

Rivets

Post slot

tapered ends

points down

BraceandBeamlonger

ledgemustbeontop.

Insideview

Andere Husky Inneneinrichtung Handbücher

Husky

Husky HOLT7202B11 Bedienungsanleitung

Husky

Husky HOLT52XDB12 Bedienungsanleitung

Husky

Husky HBR902490W5 Bedienungsanleitung

Husky

Husky H27LOCKER4 Bedienungsanleitung

Husky

Husky HOLT46XDB12 Bedienungsanleitung

Husky

Husky HTC5206 Bedienungsanleitung

Husky

Husky HOWT5201BB1XUS Bedienungsanleitung

Husky

Husky HOLT5202B11 Bedienungsanleitung

Husky

Husky H27LOCKER Bedienungsanleitung

Husky

Husky HOLT7202B12 Bedienungsanleitung

Husky

Husky MR482478W5 Bedienungsanleitung

Husky

Husky HOTL6202B12 Bedienungsanleitung

Husky

Husky HOTC5623BB2S Bedienungsanleitung

Husky

Husky HOLT5202B12 Bedienungsanleitung

Husky

Husky HOLT6202BJ2 Bedienungsanleitung

Husky

Husky HOLT4602B12 Bedienungsanleitung

Husky

Husky UACT-H-270111 Bedienungsanleitung

Husky

Husky HOET5201B11XUS Bedienungsanleitung

Husky

Husky HPRO72HUTCHBRD Bedienungsanleitung

Husky

Husky BED1008 Bedienungsanleitung

Husky

Husky ERPB4020B Bedienungsanleitung

Husky

Husky UACT-H-270101 Bedienungsanleitung

Husky

Husky HPRO27SLOCKERBLK Bedienungsanleitung

Husky

Husky Work Table HOLT62XDB12 Bedienungsanleitung

Beliebte Inneneinrichtung Handbücher anderer Marken

Homelegance

Homelegance California 1662PEK-1CK Bedienungsanleitung

Osmond Ergonomics

Osmond Ergonomics FLO Bedienungsanleitung

OVE

OVE ELOISE 42 Bedienungsanleitung

overstock

overstock MF286255 Bedienungsanleitung

Sonoma

Sonoma 160-801 Bedienungsanleitung

BOLERO

BOLERO Wicker Side Chair CF158 Installationsanleitung

Coaster

Coaster 4799N Bedienungsanleitung

Stor-It-All

Stor-It-All WS39MP Programmierhandbuch

Lexicon

Lexicon 194840161868 Bedienungsanleitung

Next AMELIA NEW 462947 Bedienungsanleitung

impekk

impekk Manual II Bedienungsanleitung

Elements

Elements Ember Nightstand CEB700NSE Bedienungsanleitung

JWA

JWA CARY 68429 Bedienungsanleitung

VIPACK

VIPACK AMORI AMKB9014 Bedienungsanleitung

Rowico

Rowico SANNA Bedienungsanleitung

Southern Enterprises

Southern Enterprises CK556000TX Bedienungsanleitung

hygena

hygena 314/5041 Bedienungsanleitung

VINNOVA

VINNOVA Kinsley 536060S Bedienungsanleitung