Husqvarna 129 LDX Bedienungsanleitung

KEY

O SYMBOLS

Symbols on the mac

hine and/or in

the manual:

ARNING! Clearing saws,

brushcutters and trimmers can be

dangerous! Careless or incorrect use

can result in serious or fatal injury to

the operator or others. It is extremely

important that you read and

understand the contents of the operator’s manual.

Please read the operator’s manual

carefully and make sure you

understand the instructions before

using the machine.

Always wear:

A protective helmet where there is a

risk of falling objects

• Approved hearing protection

• Approved eye protection

Max. speed of output shaft, rpm

Watch out for thrown objects and

ricochets.

The operator of the machine must

ensure, while working, that no

persons or animals come closer than

50 feet (15 meters).

Always wear approved protective

gloves.

Wear sturdy, non-slip boots.

Only use non-metallic, ﬂexible

cutting attachments, i.e. trimmer

heads with trimmer line.

Other symbols/decals on the mac

hine refer to special

certiﬁcation requirements for certain markets.

The engine is s

witched off by moving

the stop switch to the stop position.

CAUTION! The stop switch

automatically returns to the start

position. In order to prevent

unintentional starting, the spark plug

cap must be removed from the spark plug when

assembling, checking and/or performing maintenance.

Always wear approved protective

gloves.

Regular cleaning is required.

Visual check.

10000

50FT

15 m

50FT

15 m

The engine exhaust from this product

contains chemicals known to the State

of California to cause cancer, birth

defects or other reproductive harm.

Assist handle to be positioned

only between the arrows.

•

Note the f

ollowing before

starting:

Please read the operator’s manual carefully.

Maintenance, replacement, or repair of the emission

control devices and system may be performed by any

nonroad engine repair establishment or individual.

The Emissions Compliance Period referred to on the

Emission Compliance label indicates the number of

operating hours for which the engine has been shown to

meet Federal and California emissions requirements.



the design of the machine be modified

modifications and/or accessories can

Dear customer!

Congratulations on your choice to buy a Husqvarna

product! Husqvarna is based on a tradition that

dates back to 1689, when the Swedish King Karl XI

ordered the construction of a factory on the banks

of the Huskvarna River, for production of muskets.

The location was logical, since water power was

harnessed from the Huskvarna River to create the

water- powered plant. During over 300 years of

continuous operation, the Husqvarna factory has

produced a lot of different products, from wood

stoves to modern kitchen appliances, sewing

machines, bicycles, motorcycles etc. In 1956, the

first motor driven lawn mowers appeared, followed

by chain saws in 1959, and it is within this area

Husqvarna is working today.

Today Husqvarna is one of the leading

manufacturers in the world of forest and garden

products, with quality as our highest priority. We

develop, manufacture and market high quality motor

driven products for forestry and gardening as well

as for building and construction industry.

Your purchase gives you access to professional help

with repairs and service whenever this may be

necessary. If the retailer who sells your machine is

not one of our authorized dealers, ask for the

address of your nearest servicing dealer.

It is our wish that you will be satisfied with your

product and that it will be your companion for a long

time. Think of this operator′s manual as a valuable

document. By following its′ content (using, service,

maintenance etc) the life span and the second-hand

value of the machine can be extended. If you ever

lend or sell this machine, make sure that the borrower

or buyer gets the operator′s manual, so they will also

know how to properly maintain and use it.

Thank you for using a Husqvarna product.

Husqvarna AB has a policy of continuous product

development and therefore reserves the right to

modify the design and appearance of products without

prior notice.

For customer assistance, contact us at our website:

www.usa.husqvarna.com

INTR

ODUCTION

WHAT IS WHAT?

What is what on the grass trimmer?

129 LDX

129 LK

129 L

129 C

1 Trimmer head 11 Air lter cover

2 Cutting attachment guard 12 Air purge

3 Shaft 13 Choke control

4 Loop handle 14 Operator’s manual

5 Throttle trigger 15 Starter housing

6 Stop switch 16 Bevel gear

7 Throttle lockout 17 Grease ller cap, bevel gear

8 Spark plug cap and spark plug 18 Drive disc

9 Starter handle 19 Shaft coupling

10 Fuel tank

GENERAL SAFETY PRECA

UTIONS

Impor

tant

Personal protective equipment

HELMET

A protectiv

e helmet where there is a risk of falling objects

HEARING PROTECTION

Wear hearing protection that provides adequate noise

reduction.

EYE PROTECTION

Always wear approved eye protection. If you use a visor

then you must also wear approved protective goggles.

Approved protective goggles must comply with standard

ANSI Z87.1 in the USA or EN 166 in EU countries.

IMPORTANT!

The machine is only designed for trimming grass.

The only accessories you can operate with this engine

unit are the cutting attachments we recommend in the

chapter on Technical data.

Never use the machine if you are tired, if you have drunk

alcohol, or if you are taking medication that could affect

your vision, your judgement or your co-ordination.

Wear personal protective equipment. See instructions

under the heading ”Personal protective equipment”.

Never use a machine that has been modiﬁed in any way

from its original speciﬁcation.

Never use a machine that is faulty. Carry out the checks,

maintenance and service instructions described in this

manual. Some maintenance and service measures

must be carried out by trained and qualiﬁed specialists.

See instructions under the heading Maintenance.

All covers, guards and handles must be ﬁtted before

starting. Ensure that the spark plug cap and ignition

lead are undamaged to avoid the risk of electric shock.

The machine operator must ensure that no people or

animals come closer than 50 feet (15 m) while working.

When several operators are working in the same area

the safety distance should be at least twice the tree

height and no less than 50 feet (15 m).

Do an overall inspection of the machine before use, see

maintenance schedule.

ARNING! This machine produces an

electromagnetic ﬁeld during operation.

This ﬁeld may under some

circumstances interfere with active or

passive medical implants.To reduce the

risk of serious or fatal injury, we

recommend persons with medical

implants to consult their physician and

the medical implant manufacturer before

operating this machine.

ARNING! Running an engine in a

conﬁned or badly ventilated area can

result in death due to asphyxiation or

carbon monoxide poisoning.

ARNING! Never allow children to use or

be in the vicinity of the machine. As the

machine is equipped with a spring-

loaded stop switch and can be started by

low speed and force on the starter

handle, even small children under some

circumstances can produce the force

necessary to start the machine.This can

mean a risk of serious personal injury.

Therefore remove the spark plug cap

when the machine is not under close

supervision.

IMPOR

TANT!

A clearing saw, brushcutter or trimmer can be

dangerous if used incorrectly or carelessly, and can

cause serious or fatal injury to the operator or others. It

is extremely important that you read and understand the

contents of this operator’s manual.

You must use approved personal protective equipment

whenever you use the machine. Personal protective

equipment cannot eliminate the risk of injury but it will

reduce the degree of injury if an accident does happen.

Ask your dealer for help in choosing the right equipment.

ARNING! Listen for warning signals

or shouts when you are wearing hearing

protection. Always remove your hearing

protection as soon as the engine stops.

GENERAL SAFETY PRECA

UTIONS

GLO

VES

Gloves should be worn when necessary, e.g., when ﬁtting

cutting attachments.

BOOTS

Wear sturdy, non-slip boots.

CLOTHING

Wear clothes made of a strong fabric and avoid loose

clothing that can catch on twigs and branches. Always

wear heavy, long pants. Do not wear jewellery, shorts

sandals or go barefoot. Secure hair so it is above shoulder

level.

FIRST AID KIT

Always have a ﬁrst aid kit nearby.

Mac

hine

′

s safety equipment

This section descr

ibes the machine

′

s safety equipment,

its purpose, and how checks and maintenance should be

carried out to ensure that it operates correctly. See the

”What is what?” section to locate where this equipment is

positioned on your machine.

The life span of the machine can be reduced and the risk

of accidents can increase if machine maintenance is not

carried out correctly and if service and/or repairs are not

carried out professionally. If you need further information

please contact your nearest servicing dealer.

Throttle lockout

The throttle lockout is designed to prevent accidental

operation of the throttle control. When you press the lock

(A) (i.e.when you grasp the handle) it releases the throttle

control (B). When you release the handle the throttle

control and the throttle lockout both move back to their

original positions. This movement is controlled by two

independent return springs.This arrangement means that

the throttle control is automatically locked at the idle

setting.

Make sure the throttle control is locked at the idle setting

when the throttle lockout is released.

Press the throttle lockout and make sure it returns to its

original position when you release it.

Check that the throttle trigger and throttle lockout move

freely and that the return springs work properly.

IMPORTANT!

All servicing and repair work on the machine requires

special training.This is especially true of the machine′s

safety equipment. If your machine fails any of the

checks described below you must contact your service

agent.When you buy any of our products we guarantee

the availability of professional repairs and service. If the

retailer who sells your machine is not a servicing dealer,

ask him for the address of your nearest service agent.

WARNING! Never use a machine with

faulty safety equipment.The machine’s

safety equipment must be checked and

maintained as described in this section.

If your machine fails any of these checks

contact your service agent to get it

repaired.

GENERAL SAFETY PRECAUTIONS

See instructions under the heading “Starting”. Start the

machine and apply full throttle. Release the throttle and

check that the cutting attachment stops and remains at a

standstill. If the cutting attachment rotates with the throttle

in the idle position then the carburettor idle setting must

be checked. See instructions under the heading

Maintenance.

Stop switch

Use the stop switch to switch off the engine.

Start the engine and make sure the engine stops when

you move the stop switch to the stop setting.

Cutting attachment guard

This guard is intended to prevent loose objects from being

thrown towards the operator. The guard also protects the

operator from accidental contact with the cutting

attachment.

Check that the guard is undamaged and not cracked.

Replace the guard if it has been exposed to impact or is

cracked.

Always use the recommended guard for the cutting

attachment you are using. See chapter on Technical data.

Mufﬂer

The mufﬂer is designed to keep noise levels to a minimum

and to direct exhaust fumes away from the user.A mufﬂer

ﬁtted with a catalytic converter is also designed to reduce

harmful exhaust gases.

In countries that have a warm and dry climate there is a

signiﬁcant risk of ﬁre.We therefore ﬁt certain mufﬂers with

a spark arrestor screen. Check whether the mufﬂer on

your machine is ﬁtted with this kind of screen.

For mufﬂers it is very important that you follow the

instructions on checking, maintaining and servicing your

machine.

Never use a machine that has a faulty mufﬂer.

Regularly check that the mufﬂer is securely attached to

the machine.

If the mufﬂer on your machine is ﬁtted with a spark

arrestor screen this must be cleaned regularly. A blocked

screen will cause the engine to overheat and may lead to

serious damage.

(Starter housing removed for clarity)

WARNING! Never use a cutting

attachment without an approved guard.

See the chapter on Technical data. If an

incorrect or faulty guard is ﬁtted this can

cause serious personal injury.

WARNING! Mufﬂers ﬁtted with catalytic

converters get very hot during use and

remain so for some time after stopping.

This also applies at idle speed. Contact

can result in burns to the skin.

Remember the risk of ﬁre!

GENERAL SAFETY PRECAUTIONS

Cutting equipment

This section describes how to choose and maintain your

cutting equipment in order to:

• Reduce the risk of blade thrust.

• Obtain maximum cutting performance.

• Extend the life of cutting equipment.

Trimmer head

• Only use the recommended trimmer heads and

trimmer line. These have been tested by the

manufacturer to suit a particular engine size. This is

especially important when a fully automatic trimmer

head is used. Only use the recommended cutting

attachment. See the chapter on Technical data.

• Smaller machines generally require small trimmer

heads and vice versa. This is because when clearing

using a line the engine must throw out the line

radially from the trimmer head and overcome the

resistance of the grass being cleared.

• The length of the line is also important. A longer line

requires greater engine power than a shorter line of

the same diameter.

• Make sure that the cutter on the trimmer guard is

intact.This is used to cut the line to the correct length.

• To increase the life of the line it can be soaked in

water for a couple of days before use. This will make

the line tougher so that it lasts longer.

WARNING! The inside of the mufﬂer

contain chemicals that may be

carcinogenic. Avoid contact with these

elements in the event of a damaged

mufﬂer.

WARNING! Bear in mind that:

The exhaust fumes from the engine are

hot and may contain sparks which can

start a ﬁre. Never start the machine

indoors or near combustible material!

IMPORTANT!

Only use cutting attachments with the guards we

recommend! See the chapter on Technical data.

Refer to the instructions for the cutting attachment to

check the correct way to load the line and the correct

line diameter.

WARNING! Always stop the engine

before doing any work on the cutting

attachment.This continues to rotate even

after the throttle has been released.

Ensure that the cutting attachment has

stopped completely and disconnect the

cap from the spark plug before you

start to work on it.

WARNING! A faulty cutting attachment

may increase the risk of accidents.

IMPORTANT!

Always ensure the trimmer line is wound tightly and

evenly around the drum, otherwise the machine will

generate harmful vibration.

Fitting the trimmer guard and

trimmer head (Model 129 L)

SFit the correct trimmer guard (A) for use!"#$%!$%&

$'#((&'!%&)*+!,--.!$%&!$'#((&'!/0)'*12-(3#4)5

$#-4!/0)'*!-4$-!$%&!6#$$#4/!-4!$%&!7%)6$!)4*!7&20'&

"#$%!$%&!3-8$!9:;+

NOTE: Make sure unit is assembled cor'&2$8<!)7

7%-"4!#4!$%#7!()40)8.

Fitting the loop handle

SPosition the handle on the shaft. Note!$%)$!$%&

handle!(07$!3&!(-04$&*!3&$"&&4!$%&!$"-!)''-"7

on!$%&!7%)6$+

SFit the screw, securing plate and wing!40$!)7

7%-"4!#4!$%&!*#)/')(+

STighten!"#$!%&'(!')"*

SFit the drive disc (B) on the output shaft.

STurn the shaft until one of the holes in the!+,&-$

dis.!/0&('1!%&"#!"#$!.2,,$132'+&'(!#20$!&'!"#$!

gear!#2)1&'(*

SInsert hex wrench (C) in the hole to lock!"#$

s#/4"*

SScrew on the trimmer head (H) in the op321&"$

dir$."&2'!"2!"#$!+&,$."&2'!24!,2"/"&2'*

!!!5!62!+&17/'"0$8!42002%!"#$!&'1",)."&2'1!&'!"#$!,$-9

!!!!!!$,1$!2,+$,*

ASSEMBLY

Fitting the trimmer guard and

trimmer head (Model 129 C)

SFit the correct trimmer guard (A) for use with the

trimmer head. Hook the trimmer guard/combina-

tion guard onto the fitting on the shaft and secure

with the wing nut (B).

SFit the dust cup (C) on the shaft. The nut must be

completely covered by the dust cup.

SHold the dust cup with a wrench to prevent the

shaftfrom rotating.

SScrew the trimmer head (D) onto the shaft.

STo dismantle, follow the instructions in the rev-

erse order.

ASSEMBLY

Assembling and dismantling the

two-piece shaft (129 LDX / LK)

Assembly:

• Loosen the coupling by turning the knob.

• Align the tab of the attachment (A) with the arrow on

the coupling (B).

• Push the attachment into the coupling until the

attachment snaps into place.

Before using the unit, tighten the knob securely.

Dismantling:

• Loosen the coupling by turning the knob (at least 3

times).

• Push and hold the button (C). While securely holding

the engine end, pull the attachment straight out of the

coupling.

Andere Handbücher für 129 LDX

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Sprachen:

Andere Husqvarna Trimmer Handbücher

Husqvarna

Husqvarna BC2125 Bedienungsanleitung

Husqvarna

Husqvarna HU625HWT Bedienungsanleitung

Husqvarna

Husqvarna 227R/RD Bedienungsanleitung

Husqvarna

Husqvarna 124L Bedienungsanleitung

Husqvarna

Husqvarna 325HDA55X-Series, 325HE3X-Series, 325HE4X-Series,... Bedienungsanleitung

Husqvarna

Husqvarna 322E/325E-X Bedienungsanleitung

Husqvarna

Husqvarna 324L X-series Bedienungsanleitung

Husqvarna

Husqvarna 235 Montageanleitung

Husqvarna

Husqvarna Aspire T28-P4A Bedienungsanleitung

Husqvarna

Husqvarna 224L Bedienungsanleitung

Husqvarna

Husqvarna 545RXT AutoTune Bedienungsanleitung

Husqvarna

Husqvarna 233RJ Bedienungsanleitung

Husqvarna

Husqvarna 323C Bedienungsanleitung

Husqvarna

Husqvarna 333 RJ SERIES Bedienungsanleitung

Husqvarna

Husqvarna 327RD X-series Bedienungsanleitung

Husqvarna

Husqvarna 343F Bedienungsanleitung

Husqvarna

Husqvarna 525RJX Bedienungsanleitung

Husqvarna

Husqvarna 323P4, 325P4, 325P5 Bedienungsanleitung

Husqvarna

Husqvarna 122 LD X-series Leitfaden

Husqvarna

Husqvarna 326E X-series Bedienungsanleitung

Husqvarna

Husqvarna KLIPPO 329 L Bedienungsanleitung

Husqvarna

Husqvarna 129R Bedienungsanleitung

Husqvarna

Husqvarna 325HS75 X-series Bedienungsanleitung

Husqvarna

Husqvarna 531RS Bedienungsanleitung

Beliebte Trimmer Handbücher anderer Marken

MTD

MTD HT 51 E Bedienungsanleitung

McCulloch

McCulloch T22 LS Bedienungsanleitung

COCKRAFT

COCKRAFT PRO HL36-S Bedienungsanleitung

Grizzly

Grizzly CT 1800 Li Bedienungsanleitung

Peco

Peco Z Trimmer ZT-3000 Bedienungsanleitung

Solo

Solo 116 Bedienungsanleitung

Stiga

Stiga ST 1200 Bedienungsanleitung

Echo

Echo GT-225 - 10-09 Bedienungsanleitung

RedMax

RedMax BT17 Bedienungsanleitung

GreenWorks

GreenWorks STA806 Bedienungsanleitung

Parkside

Parkside PHSL 900 A3 Bedienungsanleitung

Gardeo

Gardeo PRO GPTHT2560 Bedienungsanleitung

Park

Park DT-810870 Bedienungsanleitung

Worx

Worx WG209 Bedienungsanleitung

Gardenline

Gardenline 43671/HTKS26 Bedienungsanleitung

Makita

Makita 3710 Bedienungsanleitung

Champion

Champion 100683 Bedienungsanleitung

Stihl

Stihl FS 311 Bedienungsanleitung