Husqvarna 325HDA55 x-series, 325HE3, 325HE3 x-series, 325HE4... Bedienungsanleitung

EEnn

nngg

ggll

llii

iiss

sshh

325HDA55

X-series

323HE3

325HE3

X-series

325HE4

X-series

Operator

′

s manual

Please read the operator’s manual carefully and make sure you

understand the instructions before using the machine.

2 –

English

KEY TO SYMBOLS

Symbols

WARNING! Incorrect or careless use of a

hedge trimmer can turn it into a dangerous

tool that can cause serious or even fatal

injury. It is extremely important that you

read and understand the contents of this

operator’s manual.

Please read the operator’s manual carefully

and make sure you understand the

instructions before using the machine.

Always wear:

• Approved hearing protection

• Protective goggles or a visor

This product is in accordance with applicable

EC directives.

Cutting tool. Do not touch the tool without

ﬁrst switching off the engine.

This machine is not electrically insulated.

If the machine touches or comes close to

high-voltage power lines it could lead to

death or serious bodily injury.Electricity can

jump from one point to another by arcing.

The higher the voltage, the greater the

distance electricity can jump. Electricity can

also travel through branches and other

objects, especially if they are wet. Always

keep a distance of at least 10 m between the machine and

high-voltage power lines and/or any objects that are touching

them. If have to work within this safe distance you should

always contact the relevant power company to make sure the

power is switched off before you start work.

This machine can be dangerous! The operator of the machine

must ensure, while working, that no persons or animals come

closer than 15 metres.

Arrows which show limits for handle

positioning.

Always wear approved protective gloves.

Wear sturdy, non-slip boots.

Noise emission to the environment according

to the European Community’s Directive. The

machine’s emission is speciﬁed in chapter

Technical data and on label.

Other symbols/decals on the machine refer to special

certiﬁcation requirements for certain markets.

The engine is switched off by moving the stop

switch to the stop position. CAUTION! The

stop switch automatically returns to the start

position. In order to prevent unintentional

starting, the spark plug cap must be removed

from the spark plug when assembling, checking and/or

performing maintenance.

Always wear approved protective gloves.

Regular cleaning is required.

Visual check.

Protective goggles or a visor must be worn.

English

– 3

CONTENTS

Contents Note the following before starting:

Please read the operator’s manual carefully.

Long-term exposure to noise can result in permanent hearing

impairment. So always use approved hearing protection.

KEY TO SYMBOLS

Symbols ....................................................................... 2

CONTENTS

Contents ...................................................................... 3

Note the following before starting: ................................ 3

INTRODUCTION

Dear Customer, ............................................................ 4

WHAT IS WHAT?

What is what? .............................................................. 5

GENERAL SAFETY PRECAUTIONS

Important ...................................................................... 6

Personal protective equipment ..................................... 6

Machine

′

s safety equipment ........................................ 7

ASSEMBLY

Fitting the hand guard and loop handle ....................... 10

Fitting the handle ......................................................... 10

Fitting the cutting head ................................................ 10

Adjusting the harness .................................................. 10

Fitting the impact guard ............................................... 10

FUEL HANDLING

Fuel safety ................................................................... 11

Fuel .............................................................................. 11

Fuelling ........................................................................ 12

STARTING AND STOPPING

Check before starting ................................................... 13

Starting and stopping ................................................... 13

WORKING TECHNIQUES

General working instructions ....................................... 15

MAINTENANCE

Carburettor ................................................................... 17

Mufﬂer .......................................................................... 18

Cooling system ............................................................ 19

Spark plug .................................................................... 19

Air ﬁlter ......................................................................... 19

Gear housing ............................................................... 20

Cleaning and lubrication .............................................. 20

Maintenance schedule ................................................. 21

TECHNICAL DATA

Technical data .............................................................. 22

EC-declaration of conformity (Applies to Europe only) . 23

WARNING! Under no circumstances may the

design of the machine be modiﬁed without

the permission of the manufacturer. Always

use genuine accessories. Non-authorized

modiﬁcations and/or accessories can result

in serious personal injury or the death of the

operator or others.

WARNING! Incorrect or careless use of a

hedge trimmer can turn it into a dangerous

tool that can cause serious or even fatal

injury. It is extremely important that you read

and understand the contents of this

operator’s manual.

4 –

English

INTRODUCTION

Dear Customer,

Congratulations on your choice to buy a Husqvarna product! Husqvarna is based on a tradition that dates back to 1689, when the

Swedish King Charles XI ordered the construction of a factory on the banks of the Husqvarna River, for production of muskets.The

location was logical, since water power was harnessed from the Huskvarna River to create the water-powered plant. During the

more than 300 years of beeing, the Husqvarna factory has produced a lot of different products, from wood stoves to modern kitchen

appliances, sewing machines, bicycles, motorcycles etc. In 1956, the ﬁrst motor driven lawn mowers appeared, followed by chain

saws in 1959, and it is within this area Husqvarna is working today.

Today Husqvarna is one of the leading manufacturers in the world of forest and garden products, with quality as our highest priority.

The business concept is to develop, manufacture and market motor driven products for forestry and gardening as well as for

building and construction industry. Husqvarna

′

s aim is also to be in the front edge according to ergonomics, usability, security and

environmental protection. That is the reason why we have developed many different features to provide our products within these

areas.

We are convinced that you will appreciate with great satisfaction the quality and performance of our product for a very long time to

come. The purchase of one of our products gives you access to professional help with repairs and service whenever this may be

necessary. If the retailer who sells your machine is not one of our authorised dealers, ask for the address of your nearest service

workshop.

It is our wish that you will be satisﬁed with your product and that it will be your companion for a long time. Think of this operator

′

manual as a valuable document. By following its

′

content (using, service, maintenance etc) the life span and the second-hand value

of the machine can be extended. If you will sell this machine, make sure that the buyer will get the operator

′

s manual.

Thank you for using a Husqvarna product.

Husqvarna AB has a policy of continuous product development and therefore reserves the right to modify the design and

appearance of products without prior notice.

English

– 5

WHAT IS WHAT?

What is what?

1 Cutter

2 Grease nipples (3)

3 Bevel gear

4 Blade guard (325HDA55)

5 Shaft

6 Front handle (325HDA55, 323HE3, 325HE3)

7 Front handle (325HE4)

8 Throttle control

9 Stop switch

10 Throttle lock

11 Harness support hook (325HE4)

12 Cylinder cover

13 Starter handle

14 Fuel tank

15 Choke control

16 Air purge

17 Air ﬁlter cover.

18 Clutch cover

19 Hand guard mounting screw (325HDA55, 323HE3,

325HE3)

20 Angle adjustment handle (323HE3, 325HE3, 325HE4)

21 Angle adjustment knob

22 Hand guard (325HDA55, 323HE3, 325HE3)

23 Combination spanner

24 Operator

′

s manual

25 Transport guard

26 Allen key

27 Harness (325HE4)

28 Impact guard (325HE4)

29 Spark plug cap and spark plug

6 –

English

GENERAL SAFETY PRECAUTIONS

Important

Personal protective equipment

HEARING PROTECTION

Wear hearing protection that provides adequate noise

reduction.

EYE PROTECTION

Always wear approved eye protection. If you use a visor then

you must also wear approved protective goggles. Approved

protective goggles must comply with standard ANSI Z87.1 in

the USA or EN 166 in EU countries.

GLOVES

Gloves should be worn when necessary, e.g., when ﬁtting

cutting attachments.

BOOTS

Wear sturdy, non-slip boots.

CLOTHING

Wear clothes made of a strong fabric and avoid loose clothing

that can catch on twigs and branches. Always wear heavy,

long pants. Do not wear jewellery, shorts sandals or go

barefoot. Secure hair so it is above shoulder level.

FIRST AID KIT

Always have a ﬁrst aid kit nearby.

IMPORTANT!

The machine is only designed for cutting branches and

twigs.

Never use a machine that has been modiﬁed in any way

from its original speciﬁcation.

Never use the machine if you are tired, if you have drunk

alcohol, or if you are taking medication that could affect your

vision, your judgement or your co-ordination.

Wear personal protective equipment. See instructions

under the heading Personal protective equipment.

Never use the machine in extreme weather conditions such

as severe cold, very hot and/or humid climates.

Never use a machine that is faulty. Carry out the checks,

maintenance and service instructions described in this

manual. Some maintenance and service measures must be

carried out by trained and qualiﬁed specialists. See

instructions under the heading Maintenance.

All covers and guards must be ﬁtted before starting. Ensure

that the spark plug cap and ignition lead are undamaged to

avoid the risk of electric shock.

WARNING! Never allow children to use or be

in the vicinity of the machine. As the

machine is equipped with a spring-loaded

stop switch and can be started by low speed

and force on the starter handle, even small

children under some circumstances can

produce the force necessary to start the

machine. This can mean a risk of serious

personal injury. Therefore remove the spark

plug cap when the machine is not under

close supervision.

WARNING! Faulty blades can increase the

risk of accidents.

IMPORTANT!

Incorrect or careless use of a hedge trimmer can turn it into

a dangerous tool that can cause serious or even fatal injury.

It is extremely important that you read and understand the

contents of this operator’s manual.

You must use approved personal protective equipment

whenever you use the machine. Personal protective

equipment cannot eliminate the risk of injury but it will

reduce the degree of injury if an accident does happen. Ask

your dealer for help in choosing the right equipment.

WARNING! Listen out for warning signals or

shouts when you are wearing hearing

protection. Always remove your hearing

protection as soon as the engine stops.

English

– 7

GENERAL SAFETY PRECAUTIONS

Machine

′′′′

s safety equipment

This section describes the machine

′

s safety equipment, its

purpose, and how checks and maintenance should be carried

out to ensure that it operates correctly. See the ”What is

what?” section to locate where this equipment is positioned

on your machine.

The life span of the machine can be reduced and the risk of

accidents can increase if machine maintenance is not carried

out correctly and if service and/or repairs are not carried out

professionally. If you need further information please contact

your nearest service workshop.

Throttle lock

The throttle lock is designed to prevent accidental operation

of the throttle control. When you press the lock (A) (i.e. when

you grasp the handle) it releases the throttle control (B).

When you release the handle the throttle control and the

throttle lock both move back to their original positions. This

movement is controlled by two independent return springs.

This arrangement means that the throttle control is

automatically locked at the idle setting.

Make sure the throttle control is locked at the idle setting

when the throttle lock is released.

Press the throttle lock and make sure it returns to its original

position when you release it.

Check that the throttle control and throttle lock move freely

and that the return springs work properly.

See instructions under the heading Start. Start the hedge

trimmer and apply full throttle. Release the throttle trigger and

check that the blades stop and remain stationary. If the blades

move when the throttle trigger is in the idle position then the

carburettor idle setting must be adjusted. See instructions

under the heading Maintenance.

Stop switch

Use the stop switch to switch off the engine.

Start the engine and make sure the engine stops when you

move the stop switch to the stop setting.

Hand guard

(325HDA55,323HE3,325HE3)

The hand guard prevents hands from coming into contact with

the moving blades, for example, if the operator loses grip on

the front handle.

Check that the hand guard is ﬁtted correctly.

Check that the hand guard is undamaged.

IMPORTANT!

All servicing and repair work on the machine requires

special training. This is especially true of the machine

′

safety equipment. If your machine fails any of the checks

described below you must contact your service agent.

When you buy any of our products we guarantee the

availability of professional repairs and service. If the retailer

who sells your machine is not a servicing dealer, ask him for

the address of your nearest service agent.

WARNING! Never use a machine with faulty

safety equipment. The machine’s safety

equipment must be checked and maintained

as described in this section. If your machine

fails any of these checks contact your

service agent to get it repaired.

8 –

English

GENERAL SAFETY PRECAUTIONS

Vibration damping system

Your machine is equipped with a vibration damping system

that is designed to minimize vibration and make operation

easier.

The machine

′

s vibration damping system reduces the transfer

of vibration between the engine unit/cutting equipment and

the machine

′

s handle unit.

Regularly check the vibration damping units for cracks or

deformation. Check that the vibration damping element is

undamaged and securely attached.

Mufﬂer

The mufﬂer is designed to keep noise levels to a minimum

and to direct exhaust fumes away from the user.

A mufﬂer ﬁtted with a catalytic converter is also designed to

reduce harmful exhaust gases.

In countries that have a warm and dry climate there is a

signiﬁcant risk of ﬁre. We therefore ﬁt certain mufﬂers with a

spark arrestor mesh. Check whether the mufﬂer on your

machine is ﬁtted with this kind of mesh.

For mufﬂers it is very important that you follow the instructions

on checking, maintaining and servicing your machine.

Never use a machine that has a faulty mufﬂer.

Regularly check that the mufﬂer is securely attached to the

machine.

If the mufﬂer on your machine is ﬁtted with a spark arrestor

mesh this must be cleaned regularly. A blocked mesh will

cause the engine to overheat and may lead to serious

damage.

WARNING! Overexposure to vibration can

lead to circulatory damage or nerve damage

in people who have impaired circulation.

Contact your doctor if you experience

symptoms of overexposure to vibration.

Such symptoms include numbness, loss of

feeling, tingling, pricking, pain, loss of

strength, changes in skin colour or

condition.These symptoms normally appear

in the ﬁngers, hands or wrists. The risk

increases at low temperatures.

WARNING! Mufﬂers ﬁtted with catalytic

converters get very hot during use and

remain so for some time after stopping.This

also applies at idle speed. Contact can result

in burns to the skin. Remember the risk of

ﬁre!

WARNING! The inside of the mufﬂer contain

chemicals that may be carcinogenic. Avoid

contact with these elements in the event of a

damaged mufﬂer.

English

– 9

GENERAL SAFETY PRECAUTIONS

Blades

To ensure good cutting results it is important that the contact

pressure between the blades is correct.The contact pressure

is adjusted by turning the screws on the underside of the bar

clockwise as far as they will go. Then turn the screws

anticlockwise a 1/4 turn. Lock the screws using the locking nut

on the top of the bar. Check that the screws are loose enough

to allow the washers under the screw heads to slide sideways.

When the blades are correctly adjusted the play between the

blades should be 0,2–0,4 mm, measured at the screws.

The edges of the blades are too hard to be ﬁled. Dull blades

should be sharpened using a grinder.

Replace the blades if they are bent or damaged.

Blade guard

(325HDA55)

The blade guard (A) is intended to protect against any part of

the body coming into contact with the blades (B).

Check that the blade guard is not damaged or distorted.

Replace the blade guard if it is bent or damaged.

Gear housing

The gear housing gets hot when the machine has been in

use. To avoid burning yourself do not touch the gear housing.

WARNING! Bear in mind that:

Engine exhaust fumes contain carbon

monoxide, which can cause carbon

monoxide poisoning. For this reason you

should not start or run the machine indoors,

or anywhere that is poorly ventilated.

The exhaust fumes from the engine are hot

and may contain sparks which can start a

ﬁre. Never start the machine indoors or near

combustible material!

10 –

English

ASSEMBLY

Fitting the hand guard and loop

handle

(325HDA55,323HE3,325HE3)

1 Assemble the hand guard and loop handle by screwing

them together. Take care to align the holes in both parts.

2 Slide the loop handle and hand guard onto the shaft.

3 Slide the spacer into the slot in the loop handle.

4 Fit the nut and screw. Do not overtighten.

5 Now make a ﬁnal adjustment to give yourself a

comfortable working position. Tighten the screw.

CAUTION! The loop handle and hand guard must not be

ﬁtted behind the arrow marked on the shaft.

Fitting the handle

(323HE3, 325HE3,325HE4)

Fit the handle using two screws.

Fitting the cutting head

It is important that the hedge trimmer is laid on a ﬂat surface

when you ﬁt the cutting head. Otherwise the cutting head may

not be ﬁtted straight.

1 Fit the cutting head to the shaft. CAUTION! Make sure the

drive shaft inside the shaft engages with the recess in the

cutting head.

2 Tighten the lower screw ﬁrst, then the upper screw.

Adjusting the harness

(325HE4)

You should always use the harness with the machine to give

maximum control over the machine and reduce the risk of

fatigue in your arms and back.

1 Put on the harness.

2 Hook the machine onto the harness support hook.

3 Adjust the length of the harness so that the support hook

is roughly level with your right hip.

Fitting the impact guard

(325HE4)

Fit the guard using the three screws and washers. Fit the two

short screws in hole A. Tighten the screws to a torque of 4

Nm. After the machine has been in use for around 20 hours,

re-tighten the screws to 4 Nm.

Andere Handbücher für 325HDA55 x-series, 325HE3, 325HE3 x-series, 325HE4...

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Husqvarna Trimmer Handbücher

Husqvarna

Husqvarna LiHD50 Gebrauchsanweisung

Husqvarna

Husqvarna 143R-II Bedienungsanleitung

Husqvarna

Husqvarna 345FR Bedienungsanleitung

Husqvarna

Husqvarna 525HE3 Bedienungsanleitung

Husqvarna

Husqvarna 535LS Bedienungsanleitung

Husqvarna

Husqvarna 143R-II Bedienungsanleitung

Husqvarna

Husqvarna BC2125 Bedienungsanleitung

Husqvarna

Husqvarna 545FR Bedienungsanleitung

Husqvarna

Husqvarna PA 1100 Bedienungsanleitung

Husqvarna

Husqvarna 326HS75X series Bedienungsanleitung

Husqvarna

Husqvarna HVT1200 Bedienungsanleitung

Husqvarna

Husqvarna 500 H Bedienungsanleitung

Husqvarna

Husqvarna 128R Bedienungsanleitung

Husqvarna

Husqvarna 129 LDX Bedienungsanleitung

Husqvarna

Husqvarna 300-SERIES COUPLING Bedienungsanleitung

Husqvarna

Husqvarna 335LS Bedienungsanleitung

Husqvarna

Husqvarna BCA850 Bedienungsanleitung

Husqvarna

Husqvarna 524R Bedienungsanleitung

Husqvarna

Husqvarna 124C Bedienungsanleitung

Husqvarna

Husqvarna 325HDA55 X Series Bedienungsanleitung

Husqvarna

Husqvarna 322R Bedienungsanleitung

Husqvarna

Husqvarna 140R Bedienungsanleitung

Husqvarna

Husqvarna 143R-II Bedienungsanleitung

Husqvarna

Husqvarna 233RJ Bedienungsanleitung

Beliebte Trimmer Handbücher anderer Marken

MTD

MTD HT 51 E Bedienungsanleitung

McCulloch

McCulloch T22 LS Bedienungsanleitung

COCKRAFT

COCKRAFT PRO HL36-S Bedienungsanleitung

Grizzly

Grizzly CT 1800 Li Bedienungsanleitung

Peco

Peco Z Trimmer ZT-3000 Bedienungsanleitung

Solo

Solo 116 Bedienungsanleitung

Stiga

Stiga ST 1200 Bedienungsanleitung

Echo

Echo GT-225 - 10-09 Bedienungsanleitung

RedMax

RedMax BT17 Bedienungsanleitung

Parkside

Parkside PHSL 900 A3 Bedienungsanleitung

Gardeo

Gardeo PRO GPTHT2560 Bedienungsanleitung

Park

Park DT-810870 Bedienungsanleitung

Worx

Worx WG209 Bedienungsanleitung

Gardenline

Gardenline 43671/HTKS26 Bedienungsanleitung

Makita

Makita 3710 Bedienungsanleitung

Champion

Champion 100683 Bedienungsanleitung

Stihl

Stihl FS 311 Bedienungsanleitung

Efco

Efco STARK 38 Handbuch