Hussmann IMPACT LWEGH Bedienungsanleitung

Low Temperature Wall and Island,

Solid and Glass Front Models

Instruction for Installing

Flat Ends

HUSSMANN CORPORATION • BRIDGETON, MO 63044-2483 U.S.A.

Merchandisers

PARTS LIST

Item Quantity Description

LG LIG/LNG LWG

1. 5 6 7 Nut Retainer 5/16 -18 (left end only)

2. 2 2 2 Tape Gasket 1/2x 1 x 120

3 1 1 1 Tape Gasket 1/2 x 1/2 x 120

4 1 1 1 Donut Gasket

5. 1 1 1 End Assembly

6. 5 6 7 Flat Washer 5/16

7. 5 6 7 Lock Washer 5/16

8. 5 6 7 Cap Screw 5/16 -18 x 11/4

9. 5 6 7 Plug Button

10. 1 1 1 Silicone Sealer

11 1 2 2 Glass Post End Cover

12. 6 6 6 Screw #8 x 1/2 Phillips

13. 1 1 1 Splashguard Channel

14. 2 2 2 Screw #8 x 1/2 Phillips Black

15. 1 1 1 Splashguard

Note: Nut retainers are factory installed in the left end, and alignment pins are factory installed in the right end of each merchandiser.

This section covers the installation of flat end panels on glass front models.

For solid front models, go to Page S1.

LG LNGH / LIGH

LNG / LIG

Glass Front Models

LWG / LWUG

LWGH / LWUGH

P/N 0391765

May, 2002

Use caution when removing the

honeycomb. A damaged honeycomb

will cause merchandisers to

perform poorly.

1Remove nut and screw from

honeycomb retainer. Remove

retainer from merchandiser.

(See Detail A)

2On the back side of the wall

case, or both sides of the island

center flue, use fingers to apply

pressure to the top of the

honeycomb. Press gently until

the top corner clears the retainer.

Moving along the honeycomb,

repeat this process to remove the

honeycomb.

P/N 0391765

Merchandisers

HUSSMANN CORPORATION • BRIDGETON, MO 63044-2483 U.S.A.

Figure 2. Remove Honeycomb with Fingers

Honeycomb

Retainer

Nut

Retainer Screw

Acrylic

Guard

Detail A

Figure 1. Remove Honeycomb

3Remove the acrylic guard from

the front side of the wall case, or

both sides of the island case by

sliding the guard up and then

forward.

4LEFT ENDS ONLY:

Verify that factory installed nut

retainers are installed in the

left-hand frame.

RIGHT ENDS ONLY:

Install Nut Retainers – 1 in

the right-hand end of the frame.

(See the next page for additional

illustrations.)

Remove alignment pins.

Low Temperature Wall and Island, Glass Front Models P/N 0391765

HUSSMANN CORPORATION • BRIDGETON, MO 63044-2483 U.S.A.

Figure 3. Remove Acrylic Guard

Figure 4. Install Nut Retainer - LG Case

P/N 0391765

Merchandisers

HUSSMANN CORPORATION • BRIDGETON, MO 63044-2483 U.S.A.

Figure 5. Install Nut Retainer - LNG / LIG / LNGH / LIGH Cases

Figure 6. Install Nut Retainer - LWG / LWGH / LWUG /

LWUGH Cases

5Apply Gaskets – 2, 3, and 4

to the case end frame, according

to Figure 7.

Lap gaskets at corners. Check

that there are no gaps between

gasket and merchandiser.

• Do not stretch gasket,

especially around corners.

• Do not butt gaskets; always lap

joints.

• Remove paper backing after

gasket is applied.

• Gasket has high tack adhesive

and must be properly placed the

first time.

Low Temperature Wall and Island, Glass Front Models P/N 0391765

HUSSMANN CORPORATION • BRIDGETON, MO 63044-2483 U.S.A.

LWG / LWGH

LWUG / LWUGH 2

1 In. FoamTape Gasket Donut Gasket

1/2In. FoamTape Gasket

234

LNG / LIG

LNGH / LIGH

Figure 7. Gasket Diagram

GLASS FRONT CASES

6Fasten End Assembly – 5 to

end frame of merchandiser using

Flat Washer – 6,

Lock Washer – 7 and

Cap Screw – 8. Tighten until

gaskets are compressed.

After end assemblies have been

tightened, insert

Plug Buttons – 9.

P/N 0391765

Merchandisers

HUSSMANN CORPORATION • BRIDGETON, MO 63044-2483 U.S.A.

Figure 8. Install End Panels

Detail B

7Apply a bead of Silicone — 10

where end and case join.

When the silicone is dry, replace

honeycomb and acrylic guard.

8Use Screw — 12, to fasten

Post End Cover — 11 where

glass wall meets the installed

end.

Low Temperature Wall and Island, Glass Front Models P/N 0391765

HUSSMANN CORPORATION • BRIDGETON, MO 63044-2483 U.S.A.

Top Rail

Figure 10. Install Glass Post End Cover

Apply Silicone

Figure 9. Apply Silicone

Detail C

9Use Screws — 12 to attach

Splashguard Channel — 13

to legs of merchandiser.

10 Use Screws — 14 to

attach Splashguard — 15

to splashguard channel.

P/N 0391765

Merchandisers

HUSSMANN CORPORATION • BRIDGETON, MO 63044-2483 U.S.A.

Figure 11. Install Splashguard Channel

Figure 12. Install Splashguard

Low Temperature Wall and Island, Solid Front Models P/N 0391765

HUSSMANN CORPORATION • BRIDGETON, MO 63044-2483 U.S.A.

PARTS LIST

Item Quantity Description

LLNLW

1. 4 4 6 Nut Retainer 5/16 -18 (Left end only)

2. 2 2 2 Tape Gasket 1/2x 1 x 120

3 1 1 1 Tape Gasket 1/2 x 1/2 x 120

4 1 1 1 Donut Gasket

5. 1 1 1 End Assembly

6. 4 4 8 Flat Washer 5/16

7. 4 4 8 Lock Washer 5/16

8. 4 4 8 Cap Screw 5/16 -18 x 11/4

9. 4 4 8 Plug Button

10. 1 1 1 Silicone Sealer

11. 6 6 6 Screw #8 x 1/2 Phillips

12. 1 1 1 Splashguard Channel

13. 2 2 2 Screw #8 x 1/2 Phillips Black

14. 1 1 1 Splashguard

Note: Nut retainers are factory installed in the left end, and alignment pins are factory installed in the right end of each merchandiser.

This section covers the installation of flat end panels on solid front models.

For glass front models, return to Page G1.

LLN / LNM / LI

LW / LWU

Solid Front Models

Use caution when removing the

honeycomb. A damaged honeycomb

will cause merchandisers to

perform poorly.

1On the back side of the wall

case, or both sides of the island

center flue, use fingers to apply

pressure to the top of the

honeycomb. Press gently until

the top corner clears the retainer.

Moving along the honeycomb,

repeat this process to remove the

honeycomb.

P/N 0391765

Merchandisers

HUSSMANN CORPORATION • BRIDGETON, MO 63044-2483 U.S.A.

Figure 1. Remove Honeycomb

Figure 2. Remove Honeycomb with Fingers

Andere Handbücher für IMPACT LWEGH

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Hussmann Kaufmann Handbücher

Hussmann

Hussmann IMPACT Excel D5XLRE Bedienungsanleitung

Hussmann

Hussmann GSVM Bedienungsanleitung

Hussmann

Hussmann ESBDVS Bedienungsanleitung

Hussmann

Hussmann MAXI-140 Bedienungsanleitung

Hussmann

Hussmann Q3-BC Bedienungsanleitung

Hussmann

Hussmann CR3-F Betriebsanleitung

Hussmann

Hussmann DM Bedienungsanleitung

Hussmann

Hussmann impact Excel C5X-LE Bedienungsanleitung

Hussmann

Hussmann Scroll Plus Fibertronic 401789 Handbuch

Hussmann

Hussmann IMPACT D5 Bedienungsanleitung

Hussmann

Hussmann PVWI Bedienungsanleitung

Hussmann

Hussmann impact Excel C5X-E Bedienungsanleitung

Hussmann

Hussmann impact Excel C2X-XLGE Bedienungsanleitung

Hussmann

Hussmann D5X-HE Bedienungsanleitung

Hussmann

Hussmann RI1 Bedienungsanleitung

Hussmann

Hussmann RMA Bedienungsanleitung

Hussmann

Hussmann D6X-URLE Bedienungsanleitung

Hussmann

Hussmann DMM Bedienungsanleitung

Hussmann

Hussmann P/N 0420057_B Bedienungsanleitung

Hussmann

Hussmann Impact Excel C2X-LGEP Bedienungsanleitung

Hussmann

Hussmann IMPACT Elite ES1S Bedienungsanleitung

Hussmann

Hussmann Impact C2-XLE Bedienungsanleitung

Hussmann

Hussmann ESGM Bedienungsanleitung

Hussmann

Hussmann Impact M3 Bedienungsanleitung

Beliebte Kaufmann Handbücher anderer Marken

FRIGOGLASS

FRIGOGLASS Flex 20 HC Bedienungsanleitung

EPTA

EPTA COSTAN RHINO MULTI Bedienungsanleitung

CASCO

CASCO Nano Cube Bedienungsanleitung

True

True GDIM-26 Bedienungsanleitung

Structural Concepts

Structural Concepts Oasis Mobile Series Montageanleitung

Haussmann

Haussmann RL Bedienungsanleitung

Howard McCray

Howard McCray R-CDS32E-4 Bedienungsanleitung

EPTA

EPTA iarp Cool Emotions Delight Lite Bedienungsanleitung

VALERA

VALERA BC 85 Bedienungsanleitung

HL Display

HL Display 3eBin Bedienungsanleitung

Dixie Narco

Dixie Narco DNCB 501E Bedienungsanleitung

APW Wyott

APW Wyott Racer DMXD-30H Bedienungsanleitung

Hoshizaki

Hoshizaki KD-90C Bedienungsanleitung

Summit

Summit SCR1006 Bedienungsanleitung

Delfield

Delfield Shelleyspeed SPM-28E Bedienungsanleitung

EPTA

EPTA iarp Cool Emotions GLEE 40 Bedienungsanleitung

Kysor/Warren

Kysor/Warren GranBering KW Leitfaden

Crane

Crane BevMAX Refresh 6 Media Bedienungsanleitung