Hussmann IMPACT RL Bedienungsanleitung

NOTES: Insulated partitions are used

in a line-up between different models

or different temperature cases, and are

installed as the line-up is set.

Carefully unpack and inspect the

insulated partition and components

to ensure there is no breakage or

damage, and there are no missing

parts.

Be sure the first merchandiser has

been positioned and leveled according

to the installation instruction.

1Remove items from case as

shown in Figure 1 (both sides of

islands).

A. Remove bumpers, rails,

packing materials, and splash-

guards from both cases.

B. Remove shelves (if

installed).

C. Remove display racks and

pans from ends to be joined.

D. Remove rear shelf supports.

E. Remove back panels from

both cases by lifting up and out

near the bottom. No tools are

necessary.

F. Remove ‘J’ molding from

door frames next to partition.

G. RLNI ONLY: Remove the

interior top panels from end that

will receive partition.

HUSSMANN CORPORATION • BRIDGETON, MO 63044-2483 U.S.A.

P/N 0396231

November, 2002

Insulated Partition

Between

Reach-In Merchandisers

Field Installation Instruction

Merchandisers

PARTS LIST

Item Quantity Description

RL/RM/RMF

RLN/RMN RLNI

1. 2 4Donut Gasket

(Ships with Case)

2. 1 2Gasket 1 x 1/2x 180 in.

3. 1 2Gasket 1/2x 1/4x 180 in.

4. 1 1Partition Assembly

5. 7 14 Flat Washer 5/16

6. 6 12 Cap Screw 5/16-18 x 21/2 in.

7. 1 2Hex Head Lock Nut 5/16-18

8. 2 4End ‘J’ Molding

9. 10 20 Shoulder Screw

Figure 1. Remove Parts

2Verify that nut retainers are

installed in the right-hand end

of the left case in the locations

shown in Figure 2.

Remove all alignment pins from

cases that will join partition.

P/N 0396231

Merchandisers

2HUSSMANN CORPORATION • BRIDGETON, MO 63044-2483 U.S.A.

Factory Installed

Nut Retainer

Alignment Pin Alignment Pin

RLNI

Figure 2. Verify Nut Retainer Installation

RL / RM

and

RLN / RMN

Insulated Connecting Partition for Reach-In –

Installation Instruction P/N 0396231

HUSSMANN CORPORATION • BRIDGETON, MO 63044-2483 U.S.A.

1 in. x 1/2in.

Donut

1/2in. x 1/4in.

Gaskets must be

applied as shown on

both sides (L & R)

of partition

Make sure area where raceway attaches to end frame

is sealed with the wider 1 in. x 1/2in. gasket.

RL / RM / RMF

and

RLN / RMN

3Apply

Donut Gasket — 1

in end frame recessed locations

of both cases as shown in

Figure 3.

Apply the wider

Foam Tape Gasket — 2

as shown in Figure 3.

• Lap gaskets at lower corners.

• Check that there are no gaps

between gasket and case.

• Do not stretch gasket,

especially around corners.

• Do not butt gaskets; always

overlap joints.

• Remove paper backing after

gasket is applied to keep

gasket free of debris.

Apply the narrower

Foam Tape Gasket — 3

around the outside of the donut

gasket on both cases as shown

in Figure 3.

Gaskets

Must Be

Applied As

Shown

Make sure area where raceway attaches to end

frame is covered with wider 1 in. x 1/2in. gasket.

1 in. x 1/2in.

Donut

1/2in. x 1/4in.

RLNI

Figure 3. Apply Gaskets to Both Cases

4With the left-hand case leveled

in its permanent position, move

the joining case into alignment

approximately 4 in. (102 mm)

from left-hand case.

Slide the

Partition Assembly — 4

between the two cases and raise

it to align its joining holes with

those in the cases.

Insert long narrow rods (or

screwdrivers) through three or

more joining holes of the cases

and the partition to maintain

alignment, then bring the cases

firmly together to compress the

gaskets against the partition.

P/N 0396231

Merchandisers

4HUSSMANN CORPORATION • BRIDGETON, MO 63044-2483 U.S.A.

Alignment Pin

Figure 4. Insert Partition

5Fasten the cases together

through the end frames with

Washers — 5 under the head

of Cap Screws — 6 as shown

in Figure 5. Thread screws into

nut retainers at the locations

shown.

Once all the cap screws and

washers are in place, tighten in

the order shown in Figure 5.

Do not attempt to draw the cases

together with the cap screws.

Push the second case against the

partition and first case, compress-

ing all gaskets. Overtightening

can distort the end frame and

cause an incomplete seal which

will result in adverse case

performance, including leakage.

At lower front location, use

Hex Head Lock Nut — 7

and Cap Screw — 6 with

Washer — 5 under the head

as shown to fasten the partition

between the cases.

Insulated Connecting Partition for Reach-In –

Installation Instruction P/N 0396231

HUSSMANN CORPORATION • BRIDGETON, MO 63044-2483 U.S.A.

Alignment Pin

Nut Retainer

Figure 5. Install Cap Screws,Washers and Hex Nut

6Fasten one

‘J’ Molding — 8

between the partition and the

door frame on each side as

shown in Figure 6 using

Shoulder Screws — 9.

Note that when fastening

through the hinge side of the

door frame, it may be necessary

to release the door retainer so

the door opens more than

90 degrees. Refer to manual that

shipped with the door.

7Replace rear shelf support, back

panels, display racks and pans,

and shelves removed in Step 1.

RLNI ONLY: First, replace the

interior top panels removed in

Step 1.

Once line-up is complete, install

bumpers and rails as shown in

Section 1 of the case installation

manual. Be sure to install the

splashguard brackets before

wiring or piping cases.

P/N 0396231

Merchandisers

6HUSSMANN CORPORATION • BRIDGETON, MO 63044-2483 U.S.A.

Figure 6. Install ‘J’ Molding

Andere Handbücher für IMPACT RL

Dieses Handbuch passt für folgende Modelle

Andere Hussmann Kaufmann Handbücher

Hussmann

Hussmann impact Excel C5X-LE Bedienungsanleitung

Hussmann

Hussmann D5L-EP Bedienungsanleitung

Hussmann

Hussmann Hussman P Bedienungsanleitung

Hussmann

Hussmann SI1N Bedienungsanleitung

Hussmann

Hussmann NAV-4 Bedienungsanleitung

Hussmann

Hussmann IMPACT IEDG1 Bedienungsanleitung

Hussmann

Hussmann D5NX-LEP Bedienungsanleitung

Hussmann

Hussmann RGD Betriebsanleitung

Hussmann

Hussmann Impact C2-XGE Bedienungsanleitung

Hussmann

Hussmann IMPACT CW2-EGE Bedienungsanleitung

Hussmann

Hussmann Specialty Products CR3HTO-HTB Bedienungsanleitung

Hussmann

Hussmann DM Bedienungsanleitung

Hussmann

Hussmann IMPACT RL Bedienungsanleitung

Hussmann

Hussmann FW Bedienungsanleitung

Hussmann

Hussmann RI2N Bedienungsanleitung

Hussmann

Hussmann GWIC Bedienungsanleitung

Hussmann

Hussmann CR3-F Betriebsanleitung

Hussmann

Hussmann impact C5-LE Bedienungsanleitung

Hussmann

Hussmann FHM Bedienungsanleitung

Hussmann

Hussmann ESS Betriebsanleitung

Hussmann

Hussmann AB Bedienungsanleitung

Hussmann

Hussmann DSF Bedienungsanleitung

Hussmann

Hussmann IMPACT D5RRI Bedienungsanleitung

Hussmann

Hussmann C2NX-XLGE Bedienungsanleitung

Beliebte Kaufmann Handbücher anderer Marken

FRIGOGLASS

FRIGOGLASS Flex 20 HC Bedienungsanleitung

EPTA

EPTA COSTAN RHINO MULTI Bedienungsanleitung

CASCO

CASCO Nano Cube Bedienungsanleitung

True

True GDIM-26 Bedienungsanleitung

Structural Concepts

Structural Concepts Oasis Mobile Series Montageanleitung

Haussmann

Haussmann RL Bedienungsanleitung

Howard McCray

Howard McCray R-CDS32E-4 Bedienungsanleitung

EPTA

EPTA iarp Cool Emotions Delight Lite Bedienungsanleitung

VALERA

VALERA BC 85 Bedienungsanleitung

HL Display

HL Display 3eBin Bedienungsanleitung

Dixie Narco

Dixie Narco DNCB 501E Bedienungsanleitung

APW Wyott

APW Wyott Racer DMXD-30H Bedienungsanleitung

Hoshizaki

Hoshizaki KD-90C Bedienungsanleitung

Summit

Summit SCR1006 Bedienungsanleitung

Delfield

Delfield Shelleyspeed SPM-28E Bedienungsanleitung

EPTA

EPTA iarp Cool Emotions GLEE 40 Bedienungsanleitung

Kysor/Warren

Kysor/Warren GranBering KW Leitfaden

Crane

Crane BevMAX Refresh 6 Media Bedienungsanleitung