Hussmann SHVSV Series Bedienungsanleitung

/SPECIALTY

U S E R M A N U A L

032018

MERCHANDISER

SHVSV BAKERY SERVICE

SHVSV - SHVSV-DWR-3-R

- SHVSV-DWR-4-R

- SHVSV-DWR-8-R

- SHVSV-DWR-10-R

- SHVSV-DWR-45IS-R

Remote

General Information 3

Case Sections 4

Installation 5

Receiving Case 5

Lifting and Transport 6

Skid Removal 7

Lifting Points 7

Dollie Placement 7

Hardware Removal 7

Level Case 8

Leg Adjustment 8

Joint Trim Pack list 9

Setting and Joining 10

Glass Adjustment 13

Body Panels Install 15

Refrigeration 16

Refrigerant Piping 16

Line Sizing 16

Oil Traps 16

Refrigerant Spec Sheet 17

Electrical 18

Merchandiser Electrical Data 18

Electrical Connections 18

Field Wiring 18

Identiﬁcation of Wiring 18

Remove Rear Raceway 19

Electrical Conduit (Electrical Box) 19

Electrical Wiring Diagram 20

DOE 2012

Energy Eciency

Compliant

Hussmann refrigerated merchandisers congured for sale for use in the United States

meet or surpass the requirements of the DOE 2012 energy eciency standards.

Table of Contents

User Information 25

Start Up 25

Load Limits 25

Basic Operation 25

Maintenance 26

Case Cleaning 26

Exterior Surfaces 26

Interior Surfaces 26

Troubleshooting 28

Case Descrip•on:

Description: Refrigerated Service Bakery Merchandiser

Shipping Damage: All equipment should be thoroughly examined for shipping damage before and

during unloading. This equipment has been carefully inspected at our factory and the carrier has

assumed responsibility for safe arrival. If damaged, either apparent or concealed, claim must be

made to the carrier Immediately.

Apparent Loss or Damage: If there is an obvious loss or damage, it must be noted on the freight bill

or express receipt and signed by the carrier’s agent; otherwise, carrier may refuse claim. The carrier

will supply necessary claim forms.

Concealed Loss or Damage: When loss or damage is not apparent until after all equipment is

uncrated, a claim for concealed damage is made. Make request in writing to carrier for inspection

within 15 days, and retain all packaging. The carrier will supply inspection report and required claim

forms.

Shortages: Check your shipment for any possible shortages of material (See Parts List page 9). If

a shortage should exist and is found to be the responsibility of Hussmann Chino, notify Hussmann

Chino. If such a shortage involves the carrier, notify the carrier immediately, and request an

inspection. Hussmann Chino will acknowledge shortages within ten days from receipt of equipment.

Hussmann Chino Product Control: The serial number and shipping date of all equipment have been

recorded in Hussmann’s ﬁles for warranty and replacement part purposes. All correspondence

pertaining to warranty or parts ordering must include the serial number of each piece of equipment

involved, in order to provide the customer with the correct parts.

Location/Store Conditions: The SHVSV refrigerated merchandiser has been designed for use only in

air conditioned stores where temperature and humidity are maintained at or below 75°F Dry bulb and

55% relative humidity. DO NOT allow air conditioning, electric fans, ovens, open doors or windows

(etc.) to create air currents around the merchandiser, as this will impair its correct operation.

This equipment is to be installed

to comply with the applicable

NEC, Federal, State ,and Local

Plumbing and Construction

Code ha ving jurisdiction.

ATTENTION

INSTALLER

/CHINO

A publication of HUSSMANN®Chino

13770 Ramona Avenue • Chino, California 91710

(909) 628-8942 FAX

(909) 590-4910

(800) 592-2060

Keep this booklet with the case at all times for future reference.

General Information

36 3/8"

38 3/8"

24"

26"

15"

20 1/4"

51 3/4"

10"

13 1/4" 22"

+3" RAISED BASE

30 1/4"

9 7/8"

CLEAR

29 1/2"

26"

SLIDE-OUT DECK

5 1/8"

1 3/8"

3 1/2"

3 1/8"

20"

38 1/2"

1 1/8"

1 1/8" 36"

REFRIG.

GFCI

RECEPTACLES

(OPTIONAL)

SHVSV-DWR-3-R

1 3/8"

3 1/2"

REAR OF CASE (SERVER SIDE)

FRONT OF CASE (CUSTOMER SIDE)

DRAIN

ELECT

FRONT

CLOSE-OFF

Elect

Refrig

Drain

20"

4 1/8"

3 1/8"

38 1/2"

39 7/8"

SHVSV-DWR-45I-R

EFR #1338

Case Sections SHVSV-DWR

Installation (Unloading)

NOTICE

Do NOT remove Foam Blocks from shelves

and glass until the merchandisers are

positioned for installation. Shelves or

merchandising glass may be damaged.

Loose

Items

Warning

Labels

Foam Blocks

in place

Boards

fastened

Case is to arrive at store as was shipped form fac-

tory. See reference above for proper shipment refer-

encing. (Not actual case)

Receiving Case

Upon receiving your new Hussmann Case all equip-

ment should be thoroughly examined for shipping

damage before and during unloading. This equipment

has been carefully inspected at our factory. Any claim

for loss or damage must be made to the carrier. The

carrier will provide any necessary inspection reports

or claim form.

If there is obvious loss or damage, it must be noted

on the freight bill or express receipt and signed by the

carrier’s agent; otherwise carrier may refuse claim.

Glass can cause bodily damage. Check support

hinges for periodic mantenance. Opening adjacent

glass simultaneously could result in but not limited

to glass breakage, damage to merchandiser, serious injury

or death. To prevent injury, when glass is open,

take adequate safety measures to protect shoppers.

SHVSV Lifting and Transport

Instructions

1. The SHVSV can be lifted by a forklift using the skid

which the merchandiser is mounted to.

2. Move the ﬁxture as close as possible to its per-

manent location and then remove all packaging.

Check for damage before discarding packaging.

Remove all separately packed accessories such

as kits and shelves.

3. Make sure that fork spacing and width will not

damage drain or come in contact with piping, or

electrical lines

4. Be sure that the forks are long enough to sup-

port beyond the center of the case but not dam-

age near components. Check for proper balance

before moving. A minimum fork length of 36” is

recommended for 68” wide cases

Installation (Cont’d)

5. The SHVSV merchandiser can be raised at one

end underneath the deck with a forklift or J-Bar if

forklift is not accesible to allow the placement of

rollers or dollies.

6. Evenly support the entire base structure on rollers

or dollies before attempting to move. Each Base

Leg must have its own dollie to properly support

the case.

WARNING

Improper placement of forks may damage

drainage piping. Use a spotter when placing

forks. Make sure that piping will not be dam-

aged. Use J-Bars or Jacks if forks cannot be

used safely

Lifting Points are typical and dependent upon size of

case and refrigeration application, drainage conﬁgu-

rations will call for altercations in Lifting Zones.

Do NOT remove shipping braces until the

merchandisers are properly anchored to the floor.

Merchandisers are top heavy and could tip over

causing serious injury. Merchandisers must

be braced before removing the lag bolts.

Skid Removal

Important: See lifting instructions to properly lift case

when being placed on dollies or permanent location.

(See page 6 for Lifting Instructions.)

Lifting Points

Leave all hardware and ﬁttings in place until case is

located at or near its preferred location. Using forklift

or J-Bar lift the case from the 2x4 boards and placing

dollies underneath each base leg, proceed to mov-

ing the case to its designated location if not done so

already.

Dollie Placement

The Illustration below demonstrates perfect place-

ment of a dollie per 1 side for both base legs of the

merchandiser.

IF APPLICABLE

(NOT ALL CASES

CARRY LEG BRACES)

Move the ﬁxture as close as possible to its perma-

nent location and then remove all packaging and

prepare to remove off Skid. Remove all separately

packed accessories such as kits, and panels. Check

for damage before discarding packaging.

Installation (Cont’d)

Hardware Removal

Remove screws as well as fastened plates bolted to

each 2x4 board at each base leg.

Remove fastened plates only upper brace legs are to

remain fastened onto case.

Fastened plate

Once the fastened plates are removed a J-Bar can

be used to lift at each end of the leg braces to re-

move the below 2x4 boards.

Installation (Cont’d)

Level Case

Position the case at the highest point. Set a long

magnetized level (4ft [1220 mm] or more) on

either underneath the deck or on top of the case.

Ensure to level case from front to back and side

to side.

Level

(4 ft[1220mm])

Leg Adjustment

Adjust the legs at each corner of the case to

level out any discrepancies in order to optimize

case performance and proper drainage.

Levelling Bolt

Lock Nut

Note: To avoid removing concrete ﬂooring, begin

line up levelling from the highest point of the

store ﬂoor.

A wrench or pliers may be used to adjust each

base leg.

• Loosen the lock nut.

• Turn the levelling bolt to raise or lower the

height of the case as necessary.

• Tighten Lock Nut to set Levelling Bolt in

place.

Joint Trim Pack list

    



 

  



 

  



   



  



!"#



 



$"#%



 



"#



 &



&'(

)))

 



"!*"!

)

 



$ )

)  



( 

  '



( 

  



""!

$



'

 



$"(+#)



) 



 !  (

)

 



&""#%"(



 



#%(&

)

 



#%"((")"(



 



#%(   

)#)#)



(+,

(-----------------

 +-------------

-----------------

----#--'---









 &.

.&! 



 &#&(







Installation (Cont’d)

Setting and Joining

The sectional construction of these models enable

them to be joined in line to give the effect of one con-

tinuous display.

An alignment pin kit is supplied with every case and

must be used in alignment.

Leveling

IMPORTANT! IT IS IMPERATIVE THAT CASES

BE LEVELED FROM FRONT TO BACK AND

SIDE TO SIDE PRIOR TO JOINING. A LEVEL

CASE IS NECESSARY TO INSURE PROPER

OPERATION, WATER DRAINAGE, GLASS

ALIGNMENT AND OPERATION OF THE HING-

ES SUPPORTING THE GLASS. LEVELING

THE CASE CORRECTLY WILL SOLVE MOST

HINGE OPERATION PROBLEMS.

Bolting Location

Joint Sealant Area Bolting Location

Follow these steps to access Bolt Loc #1

Step 1 - Remove front light can.

Step 2 - Unplug canopy lights.

Step 3 - Remove screw to lower plex.

Light Can

Plexiglass

Snapping Chalk Lines

Prepare permanent positioning by marking ﬂoors

with Chalk snap lines where cases are to be located.

Chalk lines are to run along the base or legs of

cases.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Hussmann Kaufmann Handbücher

Hussmann

Hussmann P4X-EP Bedienungsanleitung

Hussmann

Hussmann FHM Bedienungsanleitung

Hussmann

Hussmann IMPACT M1DGE Bedienungsanleitung

Hussmann

Hussmann IMPACT RL Bedienungsanleitung

Hussmann

Hussmann IMPACT LWG Bedienungsanleitung

Hussmann

Hussmann HGM-1BS Kurzanleitung

Hussmann

Hussmann FMSS-L Original Betriebsanleitung

Hussmann

Hussmann M4EP Bedienungsanleitung

Hussmann

Hussmann FHMA Bedienungsanleitung

Hussmann

Hussmann Specialty Products CR3HTO-HTB Betriebsanleitung

Hussmann

Hussmann VBL Bedienungsanleitung

Hussmann

Hussmann BSM Bedienungsanleitung

Hussmann

Hussmann P1X50-EP Bedienungsanleitung

Hussmann

Hussmann BEXDWG Bedienungsanleitung

Hussmann

Hussmann Impact Excel C6X-LEP Bedienungsanleitung

Hussmann

Hussmann NM1G Bedienungsanleitung

Hussmann

Hussmann IMPACT CW2-EGE Bedienungsanleitung

Hussmann

Hussmann Specialty ProductsCR3FO Bedienungsanleitung

Hussmann

Hussmann RL2W Bedienungsanleitung

Hussmann

Hussmann impact C5E Bedienungsanleitung

Hussmann

Hussmann MPCETNM6S Bedienungsanleitung

Hussmann

Hussmann RGSSFP Betriebsanleitung

Hussmann

Hussmann DDS Bedienungsanleitung

Hussmann

Hussmann P2NX-E Bedienungsanleitung

Beliebte Kaufmann Handbücher anderer Marken

FRIGOGLASS

FRIGOGLASS Flex 20 HC Bedienungsanleitung

EPTA

EPTA COSTAN RHINO MULTI Bedienungsanleitung

CASCO

CASCO Nano Cube Bedienungsanleitung

True

True GDIM-26 Bedienungsanleitung

Structural Concepts

Structural Concepts Oasis Mobile Series Montageanleitung

Haussmann

Haussmann RL Bedienungsanleitung

Howard McCray

Howard McCray R-CDS32E-4 Bedienungsanleitung

EPTA

EPTA iarp Cool Emotions Delight Lite Bedienungsanleitung

VALERA

VALERA BC 85 Bedienungsanleitung

HL Display

HL Display 3eBin Bedienungsanleitung

Dixie Narco

Dixie Narco DNCB 501E Bedienungsanleitung

APW Wyott

APW Wyott Racer DMXD-30H Bedienungsanleitung

Hoshizaki

Hoshizaki KD-90C Bedienungsanleitung

Summit

Summit SCR1006 Bedienungsanleitung

Delfield

Delfield Shelleyspeed SPM-28E Bedienungsanleitung

EPTA

EPTA iarp Cool Emotions GLEE 40 Bedienungsanleitung

Kysor/Warren

Kysor/Warren GranBering KW Leitfaden

Crane

Crane BevMAX Refresh 6 Media Bedienungsanleitung