Hussmann VR1-D Bedienungsanleitung

/SPECIALTY 032023

VR1-D DELI SERVICE

MERCHANDISER

USER MANUAL

Table of Contents

User Information 23

Start Up 23

Load Limits 23

Maintenance 24

Case Cleaning 24

Exterior Surfaces 24

Interior Surfaces 24

Do’s and Do Not’s 25

Troubleshooting 26

DOE 2012 Hussmann refrigerated merchandisers configured for sale for use in the United States

Energy meet or surpass the requirements of the DOE 2012 energy efficiency standards.

Efficiency

Notice/Warning 3

General Information 4

Case Sections 5

Installation 6

Receiving Case 6

Lifting and Transport 7

Drain Configuration 7

Skid Removal 8

Lifting Points 8

Dollie Placement 8

Level Case 9

Leg Adjustment 9

Setting and Joining 10-12

Body Panels Install 13

Refrigeration 14

Refrigerant Piping 14

Line Sizing 14

Oil Traps 14

Refrigerant Spec Sheet 15

Electrical 16

Merchandiser Electrical Data 16

Electrical Connections 16

Field Wiring 16

Identification of Wiring 16

Remove Rear Raceway 17

Electrical Conduit (Electrical Box) 17

Wiring Diagram Index 18

Wiring Diagrams 19

Notice

1. DO NOT load or stand over top of case. Glass breakage may occur if precautions

are disregarded.

*Broken glass can cause lacerations, cuts, and puncture wounds which may result in

severed arteries or tendons, amputations, eye injuries, or exposure to disease.

WARNING

General Information

Case Description:

Description: Refrigerated Service Deli Merchandiser

Shipping Damage: All equipment should be thoroughly examined for shipping damage before and

during unloading. This equipment has been carefully inspected at our factory and the carrier has

assumed responsibility for safe arrival. If damaged, either apparent or concealed, claim must be

made to the carrier Immediately.

Apparent Loss or Damage: If there is an obvious loss or damage, it must be noted on the freight bill

or express receipt and signed by the carrier’s agent; otherwise, carrier may refuse claim. The carrier

will supply necessary claim forms.

Concealed Loss or Damage: When loss or damage is not apparent until after all equipment is

uncrated, a claim for concealed damage is made. Make request in writing to carrier for inspection

within 15 days, and retain all packaging. The carrier will supply inspection report and required claim

forms.

Shortages: Check your shipment for any possible shortages of material (See Parts List page 9). If a

shortage should exist and is found to be the responsibility of Hussmann Chino, notify Hussmann

Chino. If such a shortage involves the carrier, notify the carrier immediately, and request an

inspection. Hussmann Chino will acknowledge shortages within ten days from receipt of equipment.

Hussmann Chino Product Control: The serial number and shipping date of all equipment have been

recorded in Hussmann’s files for warranty and replacement part purposes. All correspondence

pertaining to warranty or parts ordering must include the serial number of each piece of equipment

involved, in order to provide the customer with the correct parts.

Location/Store Conditions: The VR1-D refrigerated merchandiser has been designed for use only in

air conditioned stores where temperature and humidity are maintained at or below 75°F Dry bulb and

55% relative humidity. DO NOT allow air conditioning, electric fans, ovens, open doors or windows

(etc.) to create air currents around the merchandiser, as this will impair its correct operation.

Keep this booklet with the case at all times for future reference.

/CHINO

A publication of HUSSMANN®Chino

13770 Ramona Avenue • Chino, California 91710

(909) 628-8942 FAX

(909) 590-4910

(800) 592-2060

ATTENTION

INSTALLER

This equipment is to be installed

to comply with the applicable

NEC, Federal, State, and Local

Plumbing and Construction

Code having jurisdiction.

VR1-D

VR1-D-8 PLAN

CASE SECTIONS

Installation

Case is to arrive at store as was shipped form

factory. See reference above for proper shipment

referencing. (Not actual case)

Receiving case

Upon receiving your new Hussmann Case all

equipment should be thoroughly examined for

shipping damage before and during unloading.

This equipment has been carefully inspected at

our factory. Any claim for loss or damage must

be made to the carrier. The carrier will provide

any necessary inspection reports/ or claim

form. If there is obvious loss or damage, it must

be noted on the freight bill or express receipt

and signed by the carrier’s agent; otherwise

carrier may refuse claim.

snapping chalk Lines

Prepare permanent positioning by marking floors

with Chalk snap lines where cases are to be

located. Chalk lines are to run along the base or

legs of cases.

Warning

Labels

Loose

Items

Boards

fastened

Foam Blocks

in place

NOTICE

Do NOT remove Foam Blocks from shelves

and glass until the merchandisers are

positioned for installation. Shelves or

merchandising glass may be damaged.

Installation (cont’d)

VR1-D Lifting and Transport

Instructions

1. The VR1-D can be lifted by a forklift at

typical lifting points.

2. Ensure lower body panels are removed

before lifting with a forklift. Serious damage will

occur if the body panels are not removed.

(Shipped loose from factory)

3. Make sure that fork spacing and width will

not damage drain or come in contact with

piping, or electrical lines

4. Be sure that the forks are long enough to

sup-port beyond the center of the case but not

dam-age near components. Check for proper

balance before moving. A minimum fork length

of 36” is recommended for 68” wide cases

VR1-D-8 Drain Location

1. The VR1-D merchandiser can be raised at one

end underneath the deck with a forklift or J-Bar if

forklift is not accessible to allow the placement of

rollers or dollies.

2. Evenly support the entire base structure on

rollers or dollies before attempting to move. Each

Base Leg must have its own dolly to properly

support the case.

Lifting Points are typical and dependent upon size of

case and refrigeration application, drainage

configurations will call for altercations in Lifting

Zones.

Below are the following drainage configurations and

lifting should be altered to the expected model.

8' Case

WARNING

Improper placement of forks may damage

drainage piping. Use a spotter when placing

forks. Make sure that piping will not be dam-

aged. Use J-Bars or Jacks if forks cannot be

used safely

FORKLIFT BLADE PLACEMENT

(PLACE BLADES IN 4" REGIONS AS SHOWN}

Installation (cont’d)

Skid Removal and Placement (Channel-Style

Legs)

Important: See lifting instructions to properly lift

case when being placed on dollies or permanent

location.

First remove Blocks and L Brackets around

the case from pallet.

Proceed by setting forklifts under specified loca-

tions as instructed in the Lifting Instructions. Be

careful not to damage drains or near

components when placing forks underneath

case. A spotter is mandatory to ensure no dam-

age is caused to the case. Lift case and replace

with dollies, place near or in permanent location.

Insert Forks

Underneath

Deck

Move the fixture as close as possible to its per-

manent location and then remove all packaging

and preparing to remove off Skid. Remove all

separately packed accessories such as kits, and

panels. Check for damage before discarding

packaging.

In the case a fork lift truck is not available follow

the demonstration below to properly lift case us-

ing a Johnson Bar (J-Bar) to place on dollies to

traffic from start point to placement area.

Place J-Bar underneath base of merchandiser to

gain leverage, once lifted place Dollie under-

neath first end and slowly lower onto dollie en-

suring merchandiser is placed on stable location.

Proceed to opposite end and repeat.

Remove Block

and L bracket

Installation (cont’d)

Leveler Adjustment

(Channel-Style Legs)

Position the case at the highest point. Set a long

magnetized level (4ft [1220 mm] or more) on

either underneath the deck or on top of the case.

Ensure to level case from front to back and side

to side.

Level

(4 ft[1220mm])

Note: To avoid removing concrete flooring,

begin line up levelling from the Highest point of

the store floor.

Shim The Case

Use shims at each corner of the case to level

out any discrepancies in order to optimize case

performance and proper drainage.

Note: Metal Shims are recommended for use to

eliminate any deterioration from shims over time.

Shim

NOTICE

Longer length cases may require shims

along the center portion of the case to

maintain proper case performance and

drainage.

Installation (cont’d)

Setting and Joining

The sectional construction of these models enable

them to be joined in line to give the effect of one

continuous display.

An alignment pin kit is supplied with every case and

must be used in alignment.

Leveling

IMPORTANT! IT IS IMPERATIVE THAT CASES

BE LEVELED FROM FRONT TO BACK AND

SIDE TO SIDE PRIOR TO JOINING. A LEVEL

CASE IS NECESSARY TO ENSURE PROPER

OPERATION, WATER DRAINAGE, GLASS

ALIGNMENT AND OPERATION OF THE HING-

ES SUPPORTING THE GLASS. LEVELING

THE CASE CORRECTLY WILL HELP TO

SOLVE MOST HINGE-RELATED ISSUES.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Hussmann Kaufmann Handbücher

Hussmann

Hussmann SI3E Bedienungsanleitung

Hussmann

Hussmann Impact C2SLE Bedienungsanleitung

Hussmann

Hussmann ESC Betriebsanleitung

Hussmann

Hussmann SMB Bedienungsanleitung

Hussmann

Hussmann SM Bedienungsanleitung

Hussmann

Hussmann Impact P1 Bedienungsanleitung

Hussmann

Hussmann SMG8B Bedienungsanleitung

Hussmann

Hussmann Q1-SS Betriebsanleitung

Hussmann

Hussmann C6L-EP Bedienungsanleitung

Hussmann

Hussmann RI3 Bedienungsanleitung

Hussmann

Hussmann MAXI-140 Bedienungsanleitung

Hussmann

Hussmann ISLA Series Betriebsanleitung

Hussmann

Hussmann RMID Bedienungsanleitung

Hussmann

Hussmann JVMR Bedienungsanleitung

Hussmann

Hussmann Hussman P Bedienungsanleitung

Hussmann

Hussmann D5X-LEP Bedienungsanleitung

Hussmann

Hussmann IMPACT M4G Bedienungsanleitung

Hussmann

Hussmann IMPACT RLN Bedienungsanleitung

Hussmann

Hussmann D5X-HEP Bedienungsanleitung

Hussmann

Hussmann Impact C2-XGE Bedienungsanleitung

Hussmann

Hussmann IMPACT Excel C2NX-LE Bedienungsanleitung

Hussmann

Hussmann FWG Bedienungsanleitung

Hussmann

Hussmann C2NX-XE Bedienungsanleitung

Hussmann

Hussmann IMPACT LWEG Bedienungsanleitung

Beliebte Kaufmann Handbücher anderer Marken

FRIGOGLASS

FRIGOGLASS Flex 20 HC Bedienungsanleitung

EPTA

EPTA COSTAN RHINO MULTI Bedienungsanleitung

CASCO

CASCO Nano Cube Bedienungsanleitung

True

True GDIM-26 Bedienungsanleitung

Structural Concepts

Structural Concepts Oasis Mobile Series Montageanleitung

Haussmann

Haussmann RL Bedienungsanleitung

Howard McCray

Howard McCray R-CDS32E-4 Bedienungsanleitung

EPTA

EPTA iarp Cool Emotions Delight Lite Bedienungsanleitung

VALERA

VALERA BC 85 Bedienungsanleitung

HL Display

HL Display 3eBin Bedienungsanleitung

Dixie Narco

Dixie Narco DNCB 501E Bedienungsanleitung

APW Wyott

APW Wyott Racer DMXD-30H Bedienungsanleitung

Hoshizaki

Hoshizaki KD-90C Bedienungsanleitung

Summit

Summit SCR1006 Bedienungsanleitung

Delfield

Delfield Shelleyspeed SPM-28E Bedienungsanleitung

EPTA

EPTA iarp Cool Emotions GLEE 40 Bedienungsanleitung

Kysor/Warren

Kysor/Warren GranBering KW Leitfaden

Crane

Crane BevMAX Refresh 6 Media Bedienungsanleitung