Hy-Gain 488 Bedienungsanleitung

INSTRUCTION

M NU L

General

Description

ORDER NO. 488

Fiberglass base station antenna

/WHIP

FITTING

I/MAST

/FERRULE

COAX w/CONNECTOR

.. I~

This versatile fiberglass antenna and mount offer a variety of new base station antenna

features.

The mount - The mounting angle is completely adjustable to your specific needs. Mount

your antenna on any surface at any angle. No ground plane radials are required.

The antenna- The fiberglass mast is topped with a stainless steel whip. This loaded

Y2-wave antenna is tactory pretuned for best performance. The tuning unit in the base is

completely sealed for protection against weather.

The 488 antenna comes cumplete with everything you'll need for installation: mounting

base, 50 feet of coax, a solderless connector, and mounting hardware.

Overall length ' .122,5 inches (311,15 cm)

Input impedance .50 ohms

Frequency range .... '.,. .,.,. ,27 MHz (entire Citizens Band)

Connector ., .. ,. .... ,.,.,. ,AMP solderless connector

Installation

Instructions Determine where to install your antenna, keeping in mind that itshould be within the 50 foot

coax length from your transceiver, Mount it as high as possible away from TV antennas

and other similar obstructions,

Be sure that the mounting area is strong enough to support the mount and the antenna.

Backing plates may be used for reinforcement.

Use the mounting base as a template to mark where the installation holes will be drilled.

Use the mounting hardware provided to install the mount.

NOTE

Be sure the flat washers are placed between the bolts and the top surface of

the mount.

C UTION

When tightening the hardware in any material such as Lexan, it is difficult to feel how

tight the bolt is. For installation of the mount, the maximum recommended torque for

the mount hardware is .46 kg/

(40 in./Ibs. . If

torque wrench is not

vailable, watch

the screws heads as they are being tightened. The mounting hardware should not

cause more than aslight indent on the base material. Over-tightening the mounting

hardware may cause failure of the mount and will void your warranty.

Installation of

the Antenna Insert the stainless steel whip in the whip fitting on the top of the fiberglass mast. Use the

No, 8 allen wrench to tighten the set screw securely,

Ratchet

Adjustment Move the handle on the mount until it is in an upright position. This releases the teeth on

the ratchet foldover of the mount. Align the mount so that it stands in an upright position,

then return the handle to a down position and tighten it securely.

Use this scale to identify lengths of bolts, diameters of tubes, etc, The English inch ( ) and

foot (') can be converted to centimeters in this way.

1 inch (1 )

2,54 em

1 inch (1')

30.48 cm

Example:

42 x2,54

106.7 cm

Routing the

Coax Run the coaxial cable to your transceiver. Be careful not to let the coax rest in a place

where

can be damaged.

FLATSIDE

TOWARD

• ANT __EN§:::~. I~ ~~

~ L~~I-

1. Slip the collar and shell

over

the cable. Be sure the flat edged side of the

collar is toward the antenna.

(22~ Clm)

BRAID_

CENTER

\ -CONDUCTOR

INSULATOR

2. Remove

the outer jacket of the cable. NOTE: Do not nick or cut the

strands of the coax braid.

3. Flair the braid and

remove

the white plastic

sieeve

beneath it to within

of the flaired braid. Do not nick the center conductor.

4. Insert the center conductor of the coax cable into the contact assembly.

Bend the protruding end of the conductor

over

the end of the contact.

Mold the braid uniformly

over

the contact assembly.

--~.

5. Butt the end of the contact against a firm surface and push the shell

over

the braid.

FLANGE OF

~ONTACT ASSEMBLY

6. Use pliers to press the contact assembly into the shell as shown. Apply

pressure around the circumferance of the assembly. The flange of the

center conductor should butt against the shell.

9. Cut off any excess center conductor that extends beyond the end of the

contact.

Special Tuning

Instructions NOTE: This antenna is factory pretuned for optimum performance. Further tuning of the

antenna is possible, but this procedure should only be done by a person who is

experienced with antennas and wave frequencies.

( ) Use only a NON METALLIC screwdriver to adjust the tuning capacitor which is

located 6 to 8 from the bottom end of the antenna.

( ) Grasping the base ferrule with one hand, hold the antenna at arm's length, with the

antenna as nearly vertical as possible.

( ) Adjust the tuning capacitor for the minimum VSWR reading on the bridge. The

resonance dip to the minimum VSWR is very sharp, so adjust the capacitor slowly.

Part No.

280087

280126

511577

515852

690090

870759

878880

878904

536275

567120

650062

531579

351787

878922

878935

Description Qty

ferrule ........................•............... 1

whip fitting 1

6 x 5/16 pan head . . . . . .. . .. . .. . . .. .. .. .. .. 1

8 x

pan head. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. 1

50 ft. coax 1

coil assembly 1

fiberglass whip assembly 1

parts pack 1

'4 x 2 hex head lag screw 4

.v.

flatwasher 4

Amp field installed connector 1

8-32 x

cupset screw 1

#8 allen wrench 1

whip assembly 425 , 1

ratchet mount assembly . . . . . . . . . . . . . . . . . . .. 1

Most roofing compounds or caulks can be used to seal the mount. If silicone sealant is

used, use ONLY

GEor

Dow Corning.

Hy-Gain Electronics Corporation warrants each new product manufactured to be free

from defects in material and workmanship and agrees to remedy any such defect or to

furnish a new part in exchange for any part of any unit which under normal installation.

use, and service. discloses such defect within the ninety-day term of this warranty,

dated from the date of purchase by the originai owner. This warranty applies only tothe

original purchaser.

This warranty does not extend to any of our products which have been subjected to mis-

use neglect accident incorrect wiring not our own improper installation or to use in

violation of Instructions furnished by us. Nor does It extend to units which have been

repaired or altered outside of our factory. nor to accessories used therewith not of our

own manufacture. Hy Gain Warranty Service

Hy-Gain Electronics Corporation

4900 Superior Ave.

Lincoln. Nebraska 68504

Hy-Gain Electronics Corporation reserves the right to make any changes deemed

necessary or desirable without advance notice or incurring any obligation to make like

changes in units previously manufactured or sold.

You must furnish model number, date, place, and proof of purchase, such as acopy of

the sales receipt to establish warranty. Your letter should include all pertinent details

along with part or item numbers involved. Do not return anything until requested to do

so. No warranty card is furnished; you must supply the above information.

This warranty does not cover transportation costs that may be incurred. Hy-Gain

Electronics Corporation's sole liability is the remedy of any defect for the ninety-day

period of this warranty. Hy-Galn Electronics Corporation is not responsible for

Printed in U.S.A.

Any returned items must have prior authorization. Unexpected returns are greatly

delayed in handling. These delays can beavoided by writing in advance and furnishing

the necessary information.

Inhaltsverzeichnis

Andere Hy-Gain Antenne Handbücher

Hy-Gain

Hy-Gain AV-12AVQ Bedienungsanleitung

Hy-Gain

Hy-Gain 18HTjr Bedienungsanleitung

Hy-Gain

Hy-Gain DX-88 Bedienungsanleitung

Hy-Gain

Hy-Gain Discoverer 7-1 Bedienungsanleitung

Hy-Gain

Hy-Gain 18AVQII Bedienungsanleitung

Hy-Gain

Hy-Gain V-2R Bedienungsanleitung

Hy-Gain

Hy-Gain GPG-1B Bedienungsanleitung

Hy-Gain

Hy-Gain Super Duo-Beam Bedienungsanleitung

Hy-Gain

Hy-Gain AR-40 Bedienungsanleitung

Hy-Gain

Hy-Gain VB-25FM Bedienungsanleitung

Hy-Gain

Hy-Gain THUNDERBIRD TH6-DX Bedienungsanleitung

Hy-Gain

Hy-Gain AV-640 Bedienungsanleitung

Hy-Gain

Hy-Gain TH-11DX Bedienungsanleitung

Hy-Gain

Hy-Gain QK-710 Bedienungsanleitung

Hy-Gain

Hy-Gain LJ-115 Bedienungsanleitung

Hy-Gain

Hy-Gain LP-1009A Bedienungsanleitung

Hy-Gain

Hy-Gain LJ-203BA Bedienungsanleitung

Hy-Gain

Hy-Gain 18AVT/WB-S Bedienungsanleitung

Hy-Gain

Hy-Gain AV-6160 Bedienungsanleitung

Hy-Gain

Hy-Gain MK-80 Bedienungsanleitung

Hy-Gain

Hy-Gain Super Thunderbird TH-7DX Bedienungsanleitung

Hy-Gain

Hy-Gain Penetrator SPT-500 Bedienungsanleitung

Hy-Gain

Hy-Gain VB-214FM Bedienungsanleitung

Hy-Gain

Hy-Gain KIT-160-88 Bedienungsanleitung

Beliebte Antenne Handbücher anderer Marken

Alfa Network

Alfa Network APA-L01 Bedienungsanleitung

Naval

Naval PR-422CA Bedienungsanleitung

Feig Electronic

Feig Electronic ID ISC.ANTH200/200 Series Bedienungsanleitung

TERK Technologies

TERK Technologies TV44 Bedienungsanleitung

Directive Systems & Engineering

Directive Systems & Engineering DSE2324LYRMK Bedienungsanleitung

HP J8999A Bedienungsanleitung

MobilSat

MobilSat MSP-S Bedienungsanleitung

Steren

Steren ANT-UHF 13 Bedienungsanleitung

Novatel

Novatel 600-G Bedienungsanleitung

Radio Shack

Radio Shack Amplified VHF/UHF/FM Indoor Antenna Bedienungsanleitung

TRENDnet

TRENDnet TEW-AO12O Bedienungsanleitung

Radio Shack

Radio Shack 15-1837 Bedienungsanleitung

CommScope

CommScope CMAX-OMFX-43M-I53 Bedienungsanleitung

Ramsey Electronics

Ramsey Electronics DAP25 Bedienungsanleitung

COBHAM

COBHAM SAILOR 800 VSAT Gebrauchs- und Pflegehandbuch

Trango Systems

Trango Systems AD900-9 Bedienungsanleitung

Steren

Steren ANT-100 Bedienungsanleitung

Proxim

Proxim 5054-PA-23 Bedienungsanleitung