Hy-Gain V-6R Bedienungsanleitung

308 Industrial Park Road

Starkville, MS 39759 USA

Ph'. (662) 323-9538 FAX: (662) 323-6551

V-6R

6-Meter Collinear Gain Vertical

for 51-54 Mhz

INSTRUCTION MANUAL

General Description

The new Hy-Gain V-6R VHF antenna is a

collinear 5/8-wave omnidirectional vertical

antenna for the 51-54 MHz frequency range. The

V-6R features two sets of 1/4-wave radials

which properly decouple the lower 5/8-wave

radiator from the mast. It also features a 500

watt enclosed coil that matches the antenna to a

nominal 50 ohms.

The feedpoint is a female UHF connector that is

protected from the weather within the lower

radiator. The V-6R also features a mast-to-mast

bracket that will accept up to a 2 1/4 inch O.D.

ast.

SPECIFICATIONS

Assembly of Lower Radiator

Unpack the antenna and check the parts against

the parts list and drawings.

Select four of the radial clamps and associated

hardware and LOOSELY assemble them as

shown in Figure 1. Repeat the previous step for

the remainin

four radial clam

Slide both assemblies onto the 1 1/8" X 61" tube

assembly (Item 16) as shown in Figure I and 4.

Tighten only the eight (8) screws close to the

tube to hold the clamps in place. Place a No. 16

tubing clamp (Item 19) over the slotted end of

the tube as shown in Fi

ure 5.

Select the 1 3/8" x 44" slotted tube (Item 5) Place

a No. 16 tubing clamp (Item 19) over the slotted

end of the tube. Slide the slotted end over the

bottom end of the 1 1/8" x 61" tube assembly

until the tube touches the bottom of the bottom

radial clamp. Tighten the tubing clamp securely

Select the mast-to-mast clamps and associated

hardware and loosely assemble them as shown in

ure 2. Install the 1/4" hardware first.

Slide the assembled mast-to-mast clamp over the

bottom end of the 1 3/8" x 44" tube as shown in

Figure 2 and securely tighten the two (2) 1/4"-20

x l" bolts, nuts and lockwashers (Item Nos. 7, 10,

and 12

)

NOTE: The end of the 1 3/8" x 44" tube (Item 5)

should be even with the bottom of the mast-to-

mast clam

(

Item 9

)

Select the 1" x 60" tube assembly (Item 15).

Place a No. 10 tubing clamp (Item 18) over the

slotted end of the tube. Slide the bottom end of

this tube assembly into the top (slotted) end of the

1 1/8" x 61" tube assembly (Item 16) to the

dimension shown in Figure 4. Securely tighten

the No. 16 tubing clamp on the top of the 1 1/8" x

61" tube.

Figure 5

Compression

Clamps

Assembly of Upper Radiator

Refer to Fi

ures 3 and 5.

Select the V-6R coil assembly (Item 14). Select a

No. 10 tubing clamp (Item 18) and place over the

slotted tube end of the coil assembl

Select the 7/8" x 44" swaged tube (Item 4) and

insert the bottom end into the slotted end of the

coil assembly so that 42" is exposed. Tighten the

tubing clamp securely. Place a No. 6 tubing clamp

(Item 17) over the top (slotted) end of the 7/8"

tube.

Select the 5/8" x 38" swaged tube (Item 3) and

insert the bottom end into the slotted end of the

7/8" tube so that 35" is exposed. Tighten the

tubing clamp securely. Place a No. 6 tubing clamp

(Item 14) over the top (slotted ) end of the 5/8"

tube.

Select the 7/16" x 58" tube (Item 22) and insert

one end into the slotted end of the 5/8" tube so

that 44" is exposed. Tighten the tubing clamp

securely. Place the 7/16" caplug (Item 17) on the

end of this tube.

Final Assembl

It is recommended that you attach a short length

of coaxial cable to the antenna before installation.

After installation, you may then attach your

feedline to this cable. The short length of cable

must be at least 14 feet (4.3 m) long.

The V-6R may be fully assembled or partially

assembled before installation on your mast or

tower. Use one of the suggested methods as

described.

Select the eight (8) 7/16" x 52" radial tubes (Item

2), and insert them completely into the radial

clamps. Tighten all screws on both radial clamp

assemblies.

Place the antenna on a mast (2 1/4" O.D. max.)

using a gin-pole. Tighten the 1/4" bolts first, then

install and tighten the 5/16" hardware as shown in

Figure 2. Depending upon your requirements, you

may install the mast-to-mast clamps on your

supporting mast first, then install the antenna. Try

- this at at ground-level first!

Method 2: Partial Assembl

- Top of Tower

Attach the short length of coaxial cable to the

UHF connector on the bottom of the coil

assembly. Tighten the connector securely. Thread

the cable through the bottom radiator tubes until

the connector can be seen. Place the bottom of the

coil assembly into the top of the 1" x 61" tube

assembly and securely tighten the No.10 tubing

clamp.

Hand-tighten the screws on the radial clamps and

mark the exact position of the radial clamps with

either black tape or a permanent marker before

raising the antenna. Raise the antenna to a position

near the top of the tower. Select and install the (8)

7/16" x 52" radial tubes (Item 2) into the radial

clamps. Begin with the top set, raise the antenna

slightly, then install the bottom set. Securely

tighten all screws!

Method 1: Full Assembl

Attach the short length of coaxial cable to the

UHF connector on the bottom of the coil

assembly. Tighten the connector securely. Thread

the cable through the bottom radiator tubes until

the connector can be seen. Place the bottom of the

coil assembly into the top of the 1" x 61" tube

assembly and securely tighten the No. 10 tubing

clamp.

Place the antenna on a mast (2 1/4" O.D. max)

using a gin-pole. Tighten the 1/4" bolts first, then

install and tighten the 5/16" hardware as shown in

Figure 2. Depending upon your requirements, you

may install the mast-to-mast clamps on your

supporting mast first, then install the antenna. Try

this at

round-level first!

Method 3: Partial Assembly - Tower Side

Mount

Attach the short length of coaxial cable to the

UHF connector on the bottom of the coil

assembly. The length of this cable may be

increased so that the connection to the feedline

may be easily reached from the tower. Tighten the

connector securely. Thread the cable through the

bottom radiator tubes until the connector can be

seen. Place the bottom of the coil assembly into

the top of the 1" x 61" tube assembly and securely

tighten the No. 10 tubing clamp.

The tower (side-mount) support bracket(s) should

be installed prior to antenna installation. The

antenna should be supported at least 6 feet (2 m)

from the side of the tower for best performance.

Some detuning may be expected even at this

spacin

Hand-tighten the screws on the radial clamps and

mark the exact position of the radial clamps with

either black tape or a permanent marker before

raising the antenna. Raise the antenna to a

position near the support brackets. Select and

install the eight (8) 7/16" x 52" radial tubes (Item

2) into the radial clamps. Securely tighten all

screws!

Place the antenna on the support. Tighten the 1/4"

bolts first, then install and tighten the 5/16"

hardware as shown in Figure 2. Depending upon

your requirements, you may install the mast-to-

mast clamps on your supporting structure first,

then install the antenna. Try this at ground-level

first!

WARNING

Installation of this product near power lines is

dangerous. For your safety, follow the installation

directions.

Converting American

Measurements to Metric

Use this scale to identify lengths of bolts,

diameters of tubes, etc. The American inch (1")

and foot (1') can be converted to centimeters in

this wa

1 inch (1 ") = 2.54

cm 1 foot

(

)

= 30.48

Example:

42" x 2.54 = 106.7cm

PARTS LIST

Item

No. Part No. Description Qty

1 160012 Radial clamp, 45 degrees ........................................................... 8

2 175165 Tube, 7/16" x 52" ........................................................................8

3 190012 Tube, 5/8" x 38" ..........................................................................1

22 171533 Tube, 7/16" x 58" ........................................................................1

4 190205 Tube, 7/8" x 44" ..........................................................................1

5 191020 Tube, 13/8 " x 44" .....…………..................................................1

878785 Parts Pack, Base V-6R ............................................................... 1

6 500387 Bolt, 5/16"-18 x 5, hex head ...................................................4

7 502958 Bolt, 1/4"-20 x 1 ", hex head .................................................... 2

8 505737 Bolt, 1/4"-20 x 2", hex head .................................................... 2

9 5137000-1 Mast clamp..............................................................................2

10 554099 Nut, 1/4"-20, hex.....................................................................4

11 555747 Nut, 5/16"-18, hex...................................................................4

12 562961 Lockwasher, 1/4", internal ......................................................4

13 564792 Lockwasher, 5/16", split......................................................... 4

14 878786 Coil Assy. V-6R ..........................................................................1

15 878787 Tube Assy, V x 60". .................................................................. 1

16 878788 Tube Assy, 1 1/8" x 61". ............................................................ 1

878790 Parts Pack, V-6R.........................................................................1

17 358756 Clamp, #6, tube.......................................................................1

18 358757 Clamp, #10, tube.....................................................................3

19 358758 Clamp, #16, tube.....................................................................2

20 455644 Caplug, 7/16", black............................................................... 1

21 500160 Bolt, #10-24 x 5/8", hex head ............................................... 34

23 554071 Nut, # 10-24, hex ...................................................................34

24 565697 Lockwasher, #10, internal .................................................... 34

25 880395 Mast Clamp Assy........................................................................ l

Inhaltsverzeichnis

Andere Hy-Gain Antenne Handbücher

Hy-Gain

Hy-Gain BOLP-1013 Bedienungsanleitung

Hy-Gain

Hy-Gain AV-6160 Bedienungsanleitung

Hy-Gain

Hy-Gain 28 FM Bedienungsanleitung

Hy-Gain

Hy-Gain Discoverer 7-1 Bedienungsanleitung

Hy-Gain

Hy-Gain UB-7031DX Bedienungsanleitung

Hy-Gain

Hy-Gain Super Thunderbird TH-7DX Bedienungsanleitung

Hy-Gain

Hy-Gain GPG-2B Bedienungsanleitung

Hy-Gain

Hy-Gain DX-88 Bedienungsanleitung

Hy-Gain

Hy-Gain VB-214FM Bedienungsanleitung

Hy-Gain

Hy-Gain TH5 Bedienungsanleitung

Hy-Gain

Hy-Gain 216SAT Bedienungsanleitung

Hy-Gain

Hy-Gain TH-3JRS Bedienungsanleitung

Hy-Gain

Hy-Gain DX-77A Bedienungsanleitung

Hy-Gain

Hy-Gain MK-80 Bedienungsanleitung

Hy-Gain

Hy-Gain GPG-1B Bedienungsanleitung

Hy-Gain

Hy-Gain DB-1015A Bedienungsanleitung

Hy-Gain

Hy-Gain TH-11DX Bedienungsanleitung

Hy-Gain

Hy-Gain Penetrator SPT-500 Bedienungsanleitung

Hy-Gain

Hy-Gain AV-18VS Bedienungsanleitung

Hy-Gain

Hy-Gain 18HTjr Bedienungsanleitung

Hy-Gain

Hy-Gain V3R Bedienungsanleitung

Hy-Gain

Hy-Gain 533 Bedienungsanleitung

Hy-Gain

Hy-Gain VB-25FM Bedienungsanleitung

Hy-Gain

Hy-Gain RRK-88 Bedienungsanleitung

Beliebte Antenne Handbücher anderer Marken

Alfa Network

Alfa Network APA-L01 Bedienungsanleitung

Naval

Naval PR-422CA Bedienungsanleitung

Feig Electronic

Feig Electronic ID ISC.ANTH200/200 Series Bedienungsanleitung

TERK Technologies

TERK Technologies TV44 Bedienungsanleitung

Directive Systems & Engineering

Directive Systems & Engineering DSE2324LYRMK Bedienungsanleitung

HP J8999A Bedienungsanleitung

MobilSat

MobilSat MSP-S Bedienungsanleitung

Steren

Steren ANT-UHF 13 Bedienungsanleitung

Novatel

Novatel 600-G Bedienungsanleitung

Radio Shack

Radio Shack Amplified VHF/UHF/FM Indoor Antenna Bedienungsanleitung

TRENDnet

TRENDnet TEW-AO12O Bedienungsanleitung

Radio Shack

Radio Shack 15-1837 Bedienungsanleitung

CommScope

CommScope CMAX-OMFX-43M-I53 Bedienungsanleitung

Ramsey Electronics

Ramsey Electronics DAP25 Bedienungsanleitung

COBHAM

COBHAM SAILOR 800 VSAT Gebrauchs- und Pflegehandbuch

Trango Systems

Trango Systems AD900-9 Bedienungsanleitung

Steren

Steren ANT-100 Bedienungsanleitung

Proxim

Proxim 5054-PA-23 Bedienungsanleitung