Hyco FAN 30T Bedienungsanleitung
Tower Fan
MODEL: FAN 30T
Instruction Book
Version 1.0 March 2006
IMPORTANT SAFEGUARDS
Please keep these instructions
1. Check that the mains voltage corresponds with the rating of the appliance before
opening.
2. Read all instructions.
3. To protect against electric shock, do not immerse cords, plugs or appliances in water or
any other liquid.
4. Do not leave any appliance unattended while it is operating.
5. Close supervision is necessary when any appliance is used by or near children or infirm
persons.
6. Unplug from outlet when not in use or before cleaning.
7. Do not operate the appliance with a damaged cord or plug, or after the appliance has
been damaged in any manner. If the supply cord or appliance is damaged, it must be
replaced by the manufacturer or its service agent or a similarly qualified person in order
to avoid a hazard.
8. The use of accessory attachments not recommended by the appliance manufacturer
may cause injuries.
9. Do not use outdoors.
10. Do not let the cord hang over the edge of a table or counter or let it come into contact
with any hot surfaces.
11. To disconnect – remove the plug from the outlet. Do not pull plug out by the cord.
12. Do not use this product for anything other than its intended use. This appliance is for
household use only.
13. No liability can be accepted for any damage caused by non compliance with these
instructions or any other improper use or mishandling.
14. Always use the fan on a flat, stable surface.
15. Do not insert objects through the guard whilst the fan is operating.
Assembly
Version 1.0 March 2006
•Slot Base Foot A onto the Fan Base and pass the Power Cord through the Base Hole (see
image 1).
•Slot Base Foot B on top of Base Foot A so that both sections are fixed together (see image
2).
•Screw the Bolts into the holes to secure the Base Feet. Pass the Power Cord through the
Cord Channel and place the Plastic Grip over the top of the Power Cord. Using the screws
provided screw the Plastic Grip to the Base Foot to hold the Power Cord in place (see image
3).
Instructions for use
Plug into 220-2400V AC mains outlet and select
desired speed (1-3). Press 0 to stop the fan.
Pressing the Oscillation Button downwards which
is located above the Speed Buttons will cause the
fan to sweep back and forth. Releasing the button
will stop the oscillation. The fan will not oscillate
when the timer switch is set to 0.
Timer
Turn the Timer Switch anti-clockwise to the
desired time. The fan will automatically stop when
the Timer Switch reaches zero. When you do not
wish to use the timer set the switch at 1.
If the timer switch is set to 0 the fan will not
operate even if you set the desired Speed
Buttons.
Cleaning and Maintenance
•Switch off the power supply and pull out the plug from the mains socket before cleaning.
•A soft dry cloth is usually adequate but can be moistened with mild detergent solution if
required.
•Never clean the unit with solutions such as thinners and polishing powder etc.
Plug Replacement
•The appliance must be connected to a 240 volts AC supply by means of a three pin socket.
•The appliance is supplied with a rewireable 13 amp 3 pin plug fitted with a 3 amp fuse.
Should the fuse require replacement, it must be replaced with a fuse rated at 3 amp and
approved to BS1362.
•If the mains plug is unsuitable for the socket outlet in your home or is removed for any other
reason, then the cut off plug should be disposed of safely to prevent the hazard of electric
shock.
•There is a danger of electric shock if the cut off plug is inserted into any 13 amp socket
outlet.
Version 1.0 March 2006
The wires in the mains lead on this appliance are coloured in accordance with the following
code:
Green and Yellow – Earth
Blue – Neutral
Brown – Live
As the colours may not correspond with the markings identifying the terminals in your plug
proceed as follows.
•The green and yellow wire must be connected to the terminal in the plug which is marked
with the letter E or with the earth symbol or coloured green and yellow.
•The blue wire must be connected to the terminal marked N or coloured black.
•The brown wire must be connected to the terminal marked L or coloured red.
Conformity with Directives
zThis product is CE marked to denote conformity with Directives 73/23/EEC (Low
Voltage) and 89/336/EEC (Electromagnetic Compatibility), as amended.
zWaste electrical products should not be disposed of with household waste.
Please recycle where facilities exist. Check with your Local Authority or retailer for
recycling advice.
zHyco Manufacturing WF10 1NX 01977 517555 www.hyco.co.uk
Version 1.0 March 2006
Inhaltsverzeichnis
Andere Hyco Lüfter Handbücher
