Hydrotech 89 Valve Bedienungsanleitung

89 Valve

Water Soener Manual

Owners Manual

REVISION # 0

REVISION DATE November 19, 2015

54577

1. Read all instrucons carefully before operaon.

2. Avoid pinched o-rings during installaon by applying (provided with install kit) NSF cered lubri-

cant to all seals.

3. This system is not intended for treang water that is microbiologically unsafe or of unknown

quality without adequate disinfecon before or aer the system.

Canadian Head Oce

655 Park St.

Regina, SK S4N 5N1

U.S. Head Oce

8437 10th Avenue North

Golden Valley, MN 55427

Down Flow Valve Installation Upflow Valve Installation

IMPORTANT—PLEASE REFER TO THE PICTURE BELOW ON INLET/OUTLET SIDE OF THE

VALVE FOR UPFLOW AND DOWNLFOW CONFIGURATION

Efficiency Statement

This product is efficiency rated according to NSF/ANSI 44. The stated efficiencies are valid

only at the specified salt dosages and maximum service flow rate.

These softeners conform to NSF/ANSI 44 for the specific performance claims as verified

and substantiated by test data. These models are efficiency rated. The efficiency rating is

valid only at the stated salt dose and maximum service flow rate. They have a demand

initiated regeneration (D.I.R.) feature that complies with specific performance specifications

intended to minimize the amount of regenerant brine and water used in their operation.

These softeners have a rated softener efficiency of not less than 3350 grains of total

hardness exchange per pound of salt (based on sodium chloride) and shall not deliver more

salt than their listed ratings. The rated salt efficiency is measured by laboratory tests

described in NSF/ANSI Standard 44. These tests represent the maximum possible efficiency

that the systems can achieve. Operational efficiency is the actual efficiency after the system

has been installed. It is typically less than the efficiency due to individual application factors

including water hardness, water usage, and other contaminants that reduce the softener’s

capacity. These systems are not intended for use with water that is microbiologically unsafe

or of unknown quality without adequate disinfection before or after the system. For best

results, use plain, white nugget or pellet salt. Refer to Installation/operation manual and

warranty for further details on installation, parts and service, maintenance and further

restrictions or limitations to the use of the product.

Performance Data Sheet

Model Number 785-75C 785-100C 785-75 785-100 785-150 785-200 785-300

Qty High Capacity Resin

0.75 ft31.0 ft30.75 ft31.0 ft31.5 ft32.0 ft33.0 ft3

Rated Service Flow (gpm) 7.5 12.1 7.5 11.0 11.2 12.4 12.9

Pressure Drop at Rated Service Flow (psi) 7.0 15.0 9.0 15.0 15.0 15.0 15.0

Rated Softening Capacity (grains) 9,609 @ 2.25lbs 13,269 @ 3lbs 10,222 @ 2.25 lbs 13,269 @ 3lbs 20,443 @ 4.5lbs 27,258 @ 6lbs 40,887 @ 9lbs

Efficiency (grains/lb salt) 4,271 4,543 4,543 4,543 4,543 4,543 4,543

Max. Flow Rate to Drain (gpm) 2.0 2.4 1.5 2.0 2.4 3.5 5.0

Working Pressure

Operating Temperature

Min. 20 - Max. 125 psi

Min 39 - Max. 100 degrees Fahrenheit

89-75C 89-100C 89-75 89-100 89-150 89-200 89-300

Safety Guide

 Check and comply with your provincial /

state and local codes. You must follow

these guidelines.

 Use care when handling the water

softening system. Do not turn upside

down, drop, drag or set on sharp

protrusions.

 The water softening system works on 12

volt-60 Hz electrical power only. Be sure to

use only the included transformer.

 Transformer must be plugged into an

indoor 120 volt, grounded outlet only.

 Use clean water softening salts only, at

least 99.5% pure. NUGGET, PELLET or

coarse SOLAR salts are recommended. Do

not use rock, block, granulated or ice

cream making salts. They contain dirt and

sediments, or mush and cake, creating

maintenance problems.

 Keep the salt lid in place on the softener

unless servicing the unit or refilling with

salt.

 WARNING: This system is not

intended for treating water that is

microbiologically unsafe or of unknown

quality without adequate disinfection

before or after the system.

For your safety, the information in this manual must be followed to minimize the risk of

electric shock, property damage or personal injury.

Be sure to check the entire softener for any shipping damage or parts loss. Also note

damage to the shipping cartons. Contact the transportation company for all damage and

loss claims. The manufacturer is not responsible for damages in transit.

Small parts, needed to install the softener, are in a parts bag. To avoid loss of the small

parts, keep them in the parts bag until you are ready to use them.

Unpacking / Inspection

Table of Contents

PAGE

Unpacking / Inspection 3

Safety Guide 3

Proper Installation 4

Specification 5

Getting Started 5

Installation Instructions 7

Programming Instructions 10

Parts List 14

Care of your System 18

Warranty 19

Proper Installation

This water softening system must be properly installed and located in accordance with the

Installation Instructions before it is used.



Do not

install or store where it will not be

exposed to temperatures below freezing or

exposed to any type of weather. Water

freezing in the system will break it. Do not

attempt to treat water over 100°F.



Do not

install in direct sunlight. Excessive

sun or heat may cause distortion or other

damage to non-metallic parts.

 Properly ground to conform with all

governing codes and ordinances.

 Use only

lead-free solder and flux

for all

sweat-solder connections, as required by

state and federal codes.

 Maximum allowable inlet water pressure is

125 psi. If daytime pressure is over 80

psi, night time pressure may exceed the

maximum. Use a pressure reducing valve

to reduce the flow if necessary.

 Softener resins may degrade in the

presence of chlorine above 2 ppm. If you

have chlorine in excess of this amount,

you may experience reduced life of the

resin. In these conditions, you may wish

to consider purchasing a whole house

carbon filter softener system with a

chlorine reducing media.



WARNING:

Discard all unused parts and

packaging material after installation. Small

parts remaining after the installation could

be a choke hazard.

Specifications

Getting Started

Tools, Pipe, and Fittings, Other Materials

 Pliers

 Screwdriver

 Teflon tape

 Razor knife

 Two adjustable wrenches

 Additional tools may be required if

modification to home plumbing is required.

 Plastic inlet and outlet fittings are included

with the softener. To maintain full valve

flow, 3/4” or 1” pipes to and from the

softener fittings are recommended. You

should maintain the same, or larger, pipe

size as the water supply pipe, up to the

softener inlet and outlet.

 Use copper, brass or PEX pipe and fittings.

 Some codes may also allow for PVC plastic

pipe.

 ALWAYS install the included bypass valve,

or 3 shut-off valves. Bypass valves let you

turn off the water to the softener while still

having water throughout the house.

 5/8” OD drain line is needed for the valve

drain. A 10’ length of hose is included.

with some models.

 A length of 5/8” OD drain line tubing is

needed for the brine tank over flow fitting

(optional).

 Nugget or pellet water softener salt is

needed to fill the cabinet or brine tank.

 Continuous operation at flow rates greater than the service flow rate may affect capacity and efficiency performance.

 The manufacturer reserves the right to make product improvements which may deviate from the specifications and

descriptions stated herein, without obligation to change previously manufactured products or to note the change.

 The above capacity and flow rate specifications have not been validated by WQA.

Optional Settings - High Efficiency

Salt Used - Per Regeneration 2.3 lbs 3.0 lbs 2.3 lbs 3.0 lbs 4.5 lbs 6.0 lbs 9.0 lbs

Water Used - Regeneration 22.7 gal 28.3 gal 22.6 gal 31.6 gal 44.3 gal 60.9 gal 102.2 gal

Hardness Removal - Grains 11,250 15,000 11,250 15,000 22,500 30,000 45,000

Factory Settings - Standard Capacity

Salt Used - Per Regeneration 4.5 lbs 6.0 lbs 4.5 lbs 6.0 lbs 9.0 lbs 12.0 lbs 18.0 lbs

Water Used - Regeneration 40.5 gal 48.6 gal 34.0 gal 43.4 gal 62.7 gal 87.1 gal 139.2 gal

Hardness Removal - Grains 18,750 25,000 18,750 25,000 37,500 50,000 75,000

Optional - High Capacity

Salt Used - Per Regeneration 7.5 lbs 10.0 lbs 7.5 lbs 10.0 lbs 15.0 lbs 20.0 lbs 30.0 lbs

Water Used - Regeneration 56.1 gal 69.5 gal 49.6 gal 64.3 gal 90.3 gal 124.6 gal 196.2 gal

Hardness Removal - Grains 22,500 30,000 22,500 30,000 45,000 60,000 90,000

Resin Quantity - Cubic Feet

0.75 ft31.0 ft30.75 ft31.0 ft31.5 ft32.0 ft33.0 ft3

Tank Size 9x35 10x35 8x44 9x48 10x54 12x52 14x65

Tank Jacket / Media Loaded Yes Yes Yes Yes Yes No No

Brine Tank / Cabinet Size (Inches) 13.8 x 23.6 x 43.3 13.8 x 23.6 x 43.3 15.0 x 15.0 x 34.7 15.0 x 15.0 x 34.7 15.0 x 15.0 x 34.7 20.3 x 37.4 23.0 x 40.5

Salt Storage Capacity 175 lbs 175 lbs 240 lbs 240 lbs 240 lbs 350 lbs 420 lbs

Flow Rate @ 15 psi Pressure Drop 11.6 gpm 12.0 gpm 10.4 gpm 11.0 gpm 11.2 gpm 12.2 gpm 12.6 gpm

Flow Rate @ 25 psi Pressure Drop 15.6 gpm 16.0 gpm 14.3 gpm 15.0 gpm 15.1 gpm 16.2 gpm 16.6 gpm

Back Wash Flow Rate 2.0 gpm 2.4 gpm 1.5 gpm 2.0 gpm 2.4 gpm 3.5 gpm 5.0 gpm

Shipping Weight 93 lbs 110 lbs 105 lbs 122 lbs 155 lbs 158 lbs 244 lbs

Regeneration Type

Maximum Efficiency

Plumbing Connections

Resin Type

Electrical Requirements

Water Temperature

Water Pressure

Input 120V 60 Hz - Output 12V 650mA

Min 39 - Max. 100 degrees Fahrenheit

Min. 20 - Max. 125 psi

785-200

785-300

Counter Current / Up Flow

5,060 grains /lb salt

3/4" (Optional 1")

Canature 8% High Capacity Ion Exchange Resin

Specifications

785-75C

785-100C

785-75

785-100

785-150

75C 100C 75 100 150 200 300

 Place the softener as close as possible to

the pressure tank (well system) or water

meter (city water).

 Place the softener as close as possible to a

floor drain, or other acceptable drain point

(laundry tub, sump, standpipe, etc.).

 Connect the softener to the main water

supply pipe BEFORE the water heater. DO

NOT RUN HOT WATER THROUGH THE

SOFTENER. Temperature of water

passing through the softener must be less

than 100 deg. F.

 Keep outside faucets on hard water to

save soft water and salt.

 Do not install the softener in a place where

it could freeze. Damage caused by

freezing is not covered by the

warranty.

 Put the softener in a place water damage

is least likely to occur if a leak develops.

The manufacturer will not repair or pay for

water damage.

 A 120 volt electric outlet, is needed within

6 feet of the softener. (The transformer

has an attached 6 foot power cable.) Be

sure the electric outlet and

transformer are in an inside location,

to protect from wet weather.

 If installing in an outside location, you

must take the steps necessary to assure

the softener, installation plumbing, wiring,

etc., are as well protected from the

elements, contamination, vandalism, etc.,

as when installed indoors.

 Keep the softener out of direct

sunlight. The sun’s heat may soften and

distort plastic parts.

Where To Install The Softener

Refer to the below picture to know the installation of 89 Downflow and Uplflow Valve.

Please note the inlet/outlet orientation of the valve is opposite for downflow and upflow.

Down flow valve 89 installation instruction Up flow valve 89 installation instruction

1. If your hot water tank is electric, turn off the power to it to avoid damage to the element

in the tank.

2. If you have a private well, turn the power off to the pump and then shut off the main

water shut off valve. If you have municipal water, simply shut off the main valve. Go to

the faucet, (preferably on the lowest floor of the house) turn on the cold water until all

pressure is relieved and the flow of water stops.

3. Locate the softener tank and brine tank close to a drain where the system will be

installed. The surface should be clean and level.

4. Connect the inlet and outlet of the softener using appropriate fittings. Perform all

plumbing according to local plumbing codes.

 Use a ½” minimum pipe or tubing size for the drain line

 ON COPPER PLUMBING SYSTEMS BE SURE TO INSTALL A GROUNDING

WIRE BETWEEN THE INLET AND OUTLET PIPING TO MAINTAIN

GROUNDING.

Any solder joints near the valve must be done before connecting any piping to the valve.

Always leave at least 6" (152 mm) between the valve and joints when soldering pipes that

are connected to the valve. Failure to do this could cause damage to the valve.

5. Connect the drain hose (10 ft included) to the valve and secure it with a hose clamp (also

included). Run the drain hose to the nearest laundry tub or drain pipe. This can be ran

up overhead or down along the floor. If running the drain line more than 20 ft overhead,

it is recommended to increase the hose size to 3/4”. NEVER MAKE A DIRECT

CONNECTION INTO A WASTE DRAIN. A PHYSICAL AIR GAP OF AT LEAST 1.5” SHOULD

BE USED TO AVOID BACTERIA AND WASTEWATER TRAVELLING BACK THROUGH THE

DRAIN LINE INTO THE SOFTENER.

6. Using the Allen Key (included), place the unit in the bypass position. Slowly turn on the

main water supply. At the nearest cold treated water tap remove the faucet screen, open

the faucet and let water run a few minutes or until the system is free of any air or foreign

material resulting from the plumbing work.

7. Make sure there are no leaks in the plumbing system before proceeding. Close the water

tap when water runs clean.

8. Open the brine tank / cabinet salt lid and add water until there is approximately 3" (75

mm) of water in the tank. Do not add salt to the brine tank at this time.

9. Proceed to start up instructions.

Note: The unit is not ready for service until you complete the start-up

instructions.

Installation Instructions

Note: As the picture shows, connect the inlet and outlet according to the arrow direcon

which seeing from the top view, where you can see the mark of “Up ow” or “Down

ow” on the standard inlet and outlet connector assembly.

The installaon of 1“ integrated bypass valve：

If you use the 1” integrated bypass instead of the three manual valve, the installaon

method is showed as the picture below.

1 Use the clips to install the 1” bypass valve between the standard inlet and outlet con-

nector assembly and the inlet and outlet connector, make sure the O-ring is coated

with grease.

2. Connecon method of inlet and outlet connector：same as the above, make sure to

connect according to the direcon of arrow seeing from the top view；

3. It is also recommended to install the inlet and outlet pressure gauge and the inlet Y-type

lter；

4. When the two knobs on the bypass valve is parallel, the inlet and outlet are open, this

state of operaon is “Service”；

5. Rotate each of the two knobs in clockwise and anclockwise respecvely, when the

knobs on the bypass is in one line, the inlet and outlet are both closed, this state of op-

eraon is “By-pass”.

6. The two small quick connector at the two sides are the sample connecon for inlet and

outlet, choose the right elbow connector for taking water samples.

Soener commissioning

1. This water soening system must be properly installed（check the inlet and outlet, brine

line, drain line , power supply）and located in accordance with the installaon instruc-

ons before commissioning and pung into operaon.

2. The control panel using four touching keys, don’t operate the keys with thick gloves.

3. Open the bypass, rinse the inlet and outlet pipe with tap water. Change the control valve

to the “Manual Regeneraon” interface, iniate the control valve to the backwash pro-

cess.

4. Then close the bypass valve, slowly open the inlet valve, the raw water lling the tank

and empty the air of the system, open the valve more unl the backwash water is clean

5. Press any key to advance the control valve to the brine posion, check and make sure the

vacuum is present at the mouth of brine, and the ow rate of brine draw meet the re-

quirement.

6. Proceed to advance to the RINSE posion, allow the water to run unl it is clear. Proceed

to advance to the REFILL posion, check that the brine valve is lling water into the brine

tank, allow the valve to rell to the correct amount of water. Then advance to the SER-

VICE posion, open the outlet on the bypass.

7. Put the salt for regeneraon into the brine tank.

Programming Levels

There are 3 levels to the valve program. Master options and Factory options are typically adjusted at the fac-

tory. These options link the PCB function with the type of control valve and should not be tampered with.

Advanced options are used to configure the unit when the valve is assembled to the tank so that it can func-

tion as the proper size and intended system operation. Settings are the final options chosen when the unit is

installed to a specific location.

Button Configuration

Key Pad Configuration

MENU This funcon is to enter the basic set up informaon required at the me of installaon.

SET This funcon is to accept the values if changed and advance to the next page in the menu.

+ / - These buons are used to increase or decrease the value of the sengs while in the pro-

gramming mode.

Main Display Options

The main display page shows the Flow Rate, Date, Time Of Day, Remaining Volume, and Total Volume. The

display will alternate between the main page and the dealer information page.

PROGRAM LEVEL USER ACCESS

USER SETTINGS(I) These sengs are programmed when the unit is installed. The sengs should only be adjusted by a quali-

ed person.

MAIN MENU (II) These sengs are programmed when the unit is installed. The sengs should only be adjusted by a quali-

ed person.

ADVANCED MENU (II)

These sengs are programmed by the factory and should be adjusted when the valve is assembled into a

unit or system. It contains important sengs so the valve will operate properly for the type of system it is

intended for. The sengs should only be changed by qualied person.

HISTORY MENU (IV) This menu contains key diagnoscs for trouble shoong the system.

FACTORY MENU (V) These sengs are programmed by the factory. The sengs are important for the operaon of the valve

that should only be changed by a qualied person.

Flow Rate: 24.5 GPM

18-Apr-2015 10:35AM

Remain: 1,280 GAL

Capacity: 1,500 GAL

SET

Inhaltsverzeichnis

Andere Hydrotech Wasserspender Handbücher

Hydrotech

Hydrotech 785HE Technisches Datenblatt

Hydrotech

Hydrotech 89UF Series Bedienungsanleitung

Hydrotech

Hydrotech 7000 SXT Valve Bedienungsanleitung

Hydrotech

Hydrotech 89HE Gebrauchsanweisung

Hydrotech

Hydrotech 765 Technisches Datenblatt

Hydrotech

Hydrotech 89DF HIM Bedienungsanleitung

Hydrotech

Hydrotech 785 Series Technisches Datenblatt

Hydrotech

Hydrotech 89 HIMTLC Series Bedienungsanleitung

Hydrotech

Hydrotech 785 DF Bedienungsanleitung

Hydrotech

Hydrotech 785UF Technisches Datenblatt

Hydrotech

Hydrotech 565BM-75 Bedienungsanleitung

Hydrotech

Hydrotech 785 MBTO Bedienungsanleitung

Hydrotech

Hydrotech 6700XTR Series Bedienungsanleitung

Hydrotech

Hydrotech 565 Technisches Datenblatt

Hydrotech

Hydrotech 89DF Series Bedienungsanleitung

Hydrotech

Hydrotech 89 Gebrauchsanweisung

Hydrotech

Hydrotech 5600 Calendar Clock Valve Bedienungsanleitung

Hydrotech

Hydrotech NRV TO-150 Bedienungsanleitung

Beliebte Wasserspender Handbücher anderer Marken

Monarch Water

Monarch Water ULTIMATE MINI AQUA HE Bedienungsanleitung

Haier

Haier HLM-109B Bedienungsanleitung

abc

abc Fleck 5600SXT Bedienungsanleitung

GE GXOF18G Betriebsanleitung

Kenmore

Kenmore 625.385560 UltraFilter 650 Bedienungsanleitung

Innova

Innova CEV+ Kurzanleitung

Aries

Aries Hydra DI Handbuch

GE GNCF02H Bedienungsanleitung

ProFlo

ProFlo PFB Series Bedienungsanleitung

A.O. Smith

A.O. Smith FREZYA 300S Bedienungsanleitung

Frakco

Frakco Travelsoft RV 2400HD Bedienungsanleitung

GE GXSF30V Betriebsanleitung

Avanti

Avanti WD31EC Bedienungsanleitung

Avanti

Avanti WD360 Bedienungsanleitung

BRIO

BRIO CLCTTL520 Benutzerhandbuch

3M HCD-1 Bedienungsanleitung

Elkay

Elkay EFHFA8_2CJO Installationshandbuch

Coway

Coway CHP-671L Bedienungsanleitung