I-CAN Thunder AX 3600 Bedienungsanleitung
2
Restrictions for use
In all EU member states operation of 5150-5350 MHz is restricted to indoor use only.
USB
The equipment has to be connected to a standard USB device compliant with limited current circuit (as
per EN 62368-1-1).
Power source
Use only the Class II power adapter provided with the product. The product should be operated only
with power source of the same kind as indicated on the power adapter rating plate.
The power adapter provided is a limited power source as per EN 62368-1 Annex Q1 and it is compliant
to national standards of the specific country where the product is installed. It is strictly forbidden to use
different type of power source.
The plug-socket serves as the main disconnecting device. Be sure that the used power outlet is easily
accessible and located as close to the user as possible.
In order to reduce the risk of fire or electric shock, do not overload the electrical outlet, power strip, or
extension power cable.
Software
Please use only software release available onboard at first delivery or upon further updates by operator.
Other software releases do not guarantee compliance with essential requirements of RED Directive
2014/53/EU and may not allow the radio equipment to operate as intended.
Cleaning instructions
Unplug the product from the power outlet (or socket) and any other telecommunication interfaces
before cleaning. Use a damp cloth for cleaning. Do not use liquid or aerosol cleansers.
Maintenance
Do not open the case in order to avoid electric shock or exposition to overvoltages. Improper mounting
can cause electric shock during further use of the product. There are no parts inside the product that
can be substituted by the user.
Damage requiring service/replacement
In case the product requires service unplug the product from the electrical outlet and contact your
service provider.
Typical conditions which may require service:
– Liquid has been spilled into the product.
– The product does not operate normally when you follow the operating instructions.
– The product has been dropped or damaged.
– There are noticeable signs of overheating.
– The power cord, extension cord, or plug is damaged.
– A burning smell or smoke is perceived from the device.
SAFETY INFORMATION AND WARNINGS ON THE PRODUCT
When you use this product you shall always respect basic safety measures in order to
reduce risk of fire, electric shock or injury, following below instructions.
Before any operation is performed, please read the operation instructions and precautions
carefully in order to minimize the possibility of accidents.
Environmental conditions for product installation and use
The product shall be installed and configured in accordance with the user guide.
The product shall be used and installed indoor with a maximum ambient temperature of 40° C.
The product shall be installed in a place with a grade 2 of environmental pollution (a place without
conducting polluting agents).
The product shall not be placed near any source of heat or direct sunlight.
The product shall be placed in a well-ventilated area in order to prevent overheating. Do not cover or
block the air vents on the product. These are necessary for proper ventilation.
Do not use this product near water or in close proximity to bath tub, wash bowl, kitchen sink, or
laundry basin, in a wet basement, or near a swimming pool.
The product shall not get in contact with water and moisture. Moving the product from a cold environ-
ment to a hot one may cause moisture on some internal parts of the device. Wait until the product is
totally dry before turning it on. In case of fire, do not use water for fire-extinguishing.
The product shall not be used during a lightning storm. There is a remote risk of electric shock from
lightning.
Interface classification: The external interfaces of the product are classified as:
Telephone (Line) or FXS: ES2 circuits not subject to overvoltages.
xDSL: ES-2 circuit subject to overvoltages. This means, that although the cables
to be used for the normal connection in accordance with the installation
procedures are subject to overvoltages, the safety standards are respected.
The other telecommunication ports (LAN, USB Host) and the low voltage power supply port: ES1
circuits.
External xDSL cables must be connected only to the xDSL port. If these cables were connected to other
ports of the product not following the installation instructions, overvoltages can occur.
FXS analogue telephone ports are classified as ES2 circuits, meaning that there is no safety issue if
installation instructions are respected. FXS ports shall never be connected to analogue telephone equip-
ment placed outside the building where the product is installed.
Ethernet (LAN) and USB ports must be connected only to devices that support the same kind of inter-
face, and the cable used must not leave the building where the product is installed.
Wireless LAN
The product is provided with a Wi-Fi interface based on DSSS (Direct Sequence Spread Spectrum) and
OFDM (Orthogonal Frequency Division Modulation) radio technologies. The product complies with the
IEEE 802.11b/g/n/ac/ax standards and is Wi-Fi CertifiedTM according to Wi-Fi Alliance.
The radio equipment transmits in the 2.4GHz and 5GHz frequency bands; the maximum radio-
frequency power transmitted is lower than 100 mW (2.4GHz), 200mW (5.15GHz-5.35GHz) and 1000
mW (5.47GHz-5.725GHz)
In order to comply with human exposure to radiofrequency standards this product should be installed
and operated with 20 cm (8 inches) minimum distance between the radiator and your body.
3
UNPACKING YOUR WI-FI 6 ULTRA FAST HOME GATEWAY
Thunder Wi-Fi 6 Ultra Fast Home Gateway Power Supply DSL Splitter Grey DSL Cable
Yellow Ethernet Cable Red Ethernet Cable Safety Flyer Quck Installation Guide
4
CONNECTIONS
Camera, USB Key, Printer, HDD
USB
POWER SUPPLY
ETHERNET
PHONES
INTERNET
DUAL-BAND WI-FI
or
Gaming console
Tablet, Smartphone,
Notebook
DSL, Fiber
VoIP, Analogue
PC, TV, Gaming console, NAS, Printer
2.4 GHz
5 GHz
5
This chapter explains how to use the Configuration Wizard,
which helps the user to quickly personalize the router and set up
a connection to the Internet.
The Wizard can be launched by selecting Wizard in the drop-
down menu available by clicking the Menu icon
in the GUI Home page (see Section 3).
The Wizard comprises the following steps:
■Step 1: Selecting a language
■Step 2: Login and Password configuration
■Step 3: Entering the information for establishing a
connection to the Internet, as determined by
the Internet Service Provider (ISP)
■Step 4: Configuring Voice over IP Service (optional)
■Step 5: Assigning a name and a passphrase to secure
the Wi-Fi home network (optional)
■Step 6: Personal Data Collection (optional)
■Step 7: Summary
■Step 8: Firmware Upgrade (automatic)
Configuration Wizard
01
NOTE:
Information needed for connecting to the Internet is typically
provided by the ISP at the time a service subscription is
finalized.
6
The Welcome screen will appear (see Figure 1), showing the
i-CAN logo and the router model name.
To select a language:
1. Click ARROW DOWN next to the language name to display
the list of available languages.
2. Click to select a language from the drop-down menu. The
page refreshes with the selected language.
Click Start to initiate the setup process.
Figure 1. First Configuration Wizard - Language Selection
Step 1 – Selecting a Language
7
Next, mandatory step is user Login and Password configuration
as shown on the tab Configure User (see Figure 2).
This step allows to create User’s Login and Password for router
access.
1. Enter the name to be assigned to the user’s Login (e.g.,
“admin”)
2. Enter the password for the specified login name
3. Retype the password
When all the required information has been specified, the button
Next becomes active, allowing to proceed to Wizard Step 3.
Click Back to return to the previous Step or Next to continue
configuring the router.
Figure 2. First Configuration Wizard – User Configuration
NOTE:
This information enables users to enter router’s full
configuration.
Please make sure to save the information properly.
Step 2 – Login and Password Configuration
8
A connection to the Internet can be set up by choosing one of
the following two options (see Figure 3):
■Predefined. A list of pre-configured connections is shown,
sorted by country and type. If the ISP and the subscribed con-
nection type are present in the list, select the relevant entry
and click Next
■User Defined. If the ISP and the subscribed connection
type are not present in the list, the ISP name and connec-
tion parameters shall be manually entered, according to the
documentation that should have been provided by, or could
be obtained from the ISP.
Click Back to return to the previous Step or Next to continue
configuring the router.
If this step is taken again at a later time from the Internet
configuration page (Section 3.2) or by restarting the Wizard
from the Menu in the Home page (see Section 4.6) it would be
possible to click Skip to skip this step without any changes in the
configuration of the Internet connection.
Figure 3. First Configuration Wizard – Internet connection set up
NOTE:
Please make sure that the Internet cable is properly connected
to the router.
Step 3 – Connect to the Internet
9
As for the Internet connection setup, the configuration param-
eters to be specified in this step (see Figure 4) are typically pro-
vided by, or attainable from, the Internet Service Provider, after
applying for a Voice over IP service subscription.
Click Back to return to the previous Step, Skip to skip this step
or Next to continue setting up the device.
If this step is skipped, it would be possible to complete the
configuration of the VoIP service at a later time from the VoIP
configuration page (Section 3.5) or by restarting the Wizard
from the Menu in the Home page (see Section 4.6).
Figure 4. First Configuration Wizard – Voice Service
Step 4 – Configure Voice over IP Service
10
This step allows to specify the Wi-Fi network name (SSID) and
password by performing the following actions (refer to Figure 5)
1. Enter the name to be assigned to the network (SSID)
2. Enter the password
3. Retype the password
When all the required information has been specified, the button
Next becomes active, allowing to proceed to Wizard Step 6.
If the Skip button is pressed, no changes will be made to the cur-
rent values of SSID and password, displayed on the screen.
The configuration can be completed later on from the Wi-Fi con-
figuration page (Section 3.3) or by restarting the Wizard from
the Menu in the Home page (see Section 4.6).
The Back button can be clicked to return to the previous Step.
Figure 5. First Configuration Wizard – Wi-Fi Access Point
NOTE:
If the Wizard is run at first device switch-on or after a reset to
device factory configuration, the SSID and password will be
preset to their default values, which are printed on a label or
encoded in the QR-Code on the device itself.
After the modification of Wi-Fi parameters in the Wizard, it
will not be possible to use information printed on label or
QR-Code.
Step 5 – Wi-Fi Network Configuration
Beliebte Netzwerk-Router Handbücher anderer Marken
NETGEAR
NETGEAR FS526T - Switch Bedienungsanleitung
Korenix
Korenix JetNet 5710G Series Bedienungsanleitung
Automated Logic
Automated Logic ZN551 Betriebsanleitung
Cisco
Cisco ASR 1000 Series Bedienerhandbuch
EnGenius
EnGenius ESR-9710 Bedienungsanleitung
Cisco
Cisco 805 Series Bedienungs- und Sicherheitshinweise