I-O Wireless AWS-110 Bedienungsanleitung
Access Point User’s Guide
Model AWS-110
Version 1.1
2
TABLE OF CONTENTS
1 INTRODUCTION ..............................................................................................3
2 CONNECT THE ACCESS POINT TO THE NETWORK ...................................4
2.1 Install the Hardware...................................................................................4
2.2 Configure the Access Point .......................................................................4
3 USB DRIVER INSTALLATION..........................................................................5
3.1 Install Driver Under Windows 98 ...............................................................5
3.2 Install Driver Under Windows Me ..............................................................6
3.3 Install Driver Under Windows 2000 ...........................................................6
4 INSTALL THE CONFIGURATION UTILITIES ..................................................8
5 USB CONFIGURATION UTILITY .....................................................................9
5.1 Access the USB Configuration Utility.........................................................9
5.2 Setting the IP Address...............................................................................9
5.3 Configuration Utility..................................................................................11
5.4 Firmware Download.................................................................................14
5.5 Version Information .................................................................................15
5.6 Exit the Utility...........................................................................................15
6 SNMP MANAGER CONFIGURATION UTILITY .............................................16
6.1 Access the SNMP Manager Configuration Utility.....................................16
6.2 Setting the IP Address.............................................................................17
6.3 File...........................................................................................................17
6.3.1 Find Access Point ..........................................................................17
6.3.2 Connect to Access Point ................................................................18
6.3.3 Download Changes........................................................................19
6.4 Setup .......................................................................................................20
6.4.1 Bridge IP Configuration ..................................................................20
6.4.2 Privacy Option................................................................................21
6.4.3 Wireless Operational Settings........................................................22
6.5 Commands ..............................................................................................24
6.5.1 Reset Device..................................................................................24
6.5.2 Restore Defaults ............................................................................24
6.6 Info...........................................................................................................25
6.7 Traps .......................................................................................................26
6.8 Network ...................................................................................................26
6.9 Help .........................................................................................................27
7 FIRMWARE UPGRADE UTILITY ...................................................................28
FCC COMPLIANCE NOTICES...........................................................................29
TECHNICAL SPECIFICATIONS.........................................................................30
HARDWARE WARRANTY .................................................................................32
SOFTWARE LICENSE AGREEMENT................................................................33
PRODUCT SUPPORT AND WARRANTY ADMINISTRATION POLICY ............35
3
1 Introduction
The I-O Wireless Access Point allows you to create an infrastructure type
wireless network (LAN). The wireless Access Point converts airwave data into
wired Ethernet data, acting as a bridge between the wired LAN and wireless
clients. Connecting multiple Access Points via a wired Ethernet backbone can
further extend the wireless network coverage. As a mobile computing device
moves out of the range of one access point, it moves into the range of another.
As a result, wireless clients can freely roam from one access point domain to
another and still maintain seamless connection to the network.
Features:
•Complies with the IEEE 802.11b Direct Sequence Spread specification
•Complies with IEEE 802.3 specification
•Supports 11, 5.5, 2 and 1 Mbps Data Rates on the wireless interface
•Supports 10 Mbps Data Rate on the Ethernet interface
•WEP 64-bit data encryption for security
•Roaming capability
•Provides SNMP V1 management
•Remote management via SNMP protocol
•Local management via USB interface
•Firmware upgrade via USB interface
•Requires 5V@800mA power supply
•FCC Certified under Part 15 to Operate in 2.4GHz ISM Band
•Driver Support Microsoft Windows ® 98, Me and 2000
4
2 Connect the Access Point to the
Network
2.1 Install the Hardware
Connecting the I-O Wireless Access Point to the network is as simple as
connecting a hub or switch to another hub or switch.
1. Connect the Ethernet port of the Access Point to a hub or switch.
2. Connect the power supply to the Access Point. The three LEDs will turn on.
The middle LED will flicker as it is an indicator of activity on the Ethernet line.
2.2 Configure the Access Point
Configuring the Access Point involves setting the IP Address, a sub-net mask,
assigning a wireless network name, and setting up security for the wireless
network. There are a number of other configuration parameters that may be set,
but using the default values generally meets the needs of most installations.
There are two ways to configure the Access Point:
•Locally using the USB interface. This method connects a PC directly to the
Access Point using the USB interface. A USB driver and configuration utility
must be installed on the PC to use this method.
•Remotely using the Ethernet link. This method uses an SNMP configuration
utility installed on a PC to connect to the Access Point over the Ethernet link.
The following sections describe how to install the USB driver and configuration
utilities as well as using the utilities to configure the Access Point. After you
determine which configuration method you will use (locally with USB or remotely
via Ethernet) go to the appropriate section.
Note: If you are going to the USB interface, you will need to install the USB
driver before installing the configuration utilities.
5
3 USB Driver Installation
The USB Driver is installed on the PC that will be connected to the Access Point
via the USB cable. With this type of connection, you will be able to configure the
Access Point prior to using it on the Ethernet LAN.
1. Connect the Access Point:
a. To your computer using the USB cable
b. To the LAN hub or switch using the Ethernet cable
c. To the power supply
2. Insert the Utility CD into the CD-ROM drive.
3. Proceed to the one of the three following sections depending upon the
version of Windows on your PC.
3.1 Install Driver Under Windows 98
4. Windows 98 automatically recognizes a new USB Device. Click the Next
button to proceed.
5. Select Search for the best driver for your device. Click Next.
6. Select Specify a location. Enter the driver location as “d:\Driver” (d: is your
CD-ROM drive). Click Next.
7. Windows is now ready to install the driver. Click Next.
8. After Windows copies the files from your CD, you will be notified that
installation has been completed. Click Finish to complete the installation.
9. To verify that the USB driver has been installed, right click the mouse on the
My Computer icon and select Properties. Click Device Manager. The
Wireless 802.11b Access Point will be listed if the driver installation was
successful.
10.Proceed to the Install the Configuration Utilities section to install the USB
Configuration Utility, and then configure the Access Point using the utility.
6
3.2 Install Driver Under Windows Me
4. Windows ME automatically recognizes a new USB Device added. Select
Specify the location of the driver. Click the Next button to proceed.
5. At this point, Windows will ask you for new drivers. Make sure that Search for
the best driver for your device and Specify a location options are
selected. Enter the driver location as “d:\Driver” (d: is your CD-ROM drive).
Click Next.
6. Windows is now ready to install the driver. Click Next.
7. Windows will indicate that installation is complete. Click Finish to complete
the installation.
8. To verify that the USB driver has been installed, right click the mouse on the
My Computer icon and select Properties. Click Device Manager. The
Wireless 802.11b Access Point will be listed if the driver installation was
successful.
9. Proceed to the Install the Configuration Utilities section to install the USB
Configuration Utility, and then configure the Access Point using the utility.
3.3 Install Driver Under Windows 2000
4. Windows 2000 automatically recognizes the Wireless Access Point when it is
connected to the PC. Click the Next button to proceed.
5. Select Search for a suitable driver for my device. Click Next.
6. Select Specify a location. Click Next.
7. Enter the driver location as “d:\Driver” (d: is your CD-ROM drive). Click OK.
8. Windows is now ready to install the driver. Click Next.
9. Windows will indicate that installation is complete. Click Finish to complete
the installation.
10.To verify that the USB driver has been installed, right click the mouse on the
My Computer icon and select Properties. Select Hardware and click Device
Manager. The Wireless 802.11b Access Point will be listed if the driver
installation was successful.
7
11.Proceed to the Install the Configuration Utilities section to install the USB
Configuration Utility, and then configure the Access Point using the utility.
8
4 Install the Configuration Utilities
The configuration utilities must be installed before the Access Point can be
configured.
1. Execute the Setup.exe file found in the Utility sub-directory on the CD-
ROM. Click Start | Run and enter “d:\Utility\setup.exe” (d: is your CD-ROM
drive). Click OK.
2. Windows will bring you to the InstallShield Wizard screen. Click Next.
3. At this point, Windows will ask for the destination folder. Either accept the
default or enter a folder of your choice. Click Next.
4. Windows will ask for the program folder. Either accept the default or enter a
folder of your choice. Click Next.
5. Windows will indicate that installation has been completed. Click Finish to
complete the installation.
6. Proceed to either the USB Configuration Utility or SNMP Manager
Configuration Utility section to setup the configuration parameters for the
Access Point.
9
5 USB Configuration Utility
The USB Configuration Utility is used when the Access Point is connected
directly to a PC.
5.1 Access the USB Configuration Utility
1. Using the USB cable, connect the Access Point to computer where the USB
driver has been installed.
2. Select the USB Configuration Utility option from within the Wireless
802.11b Access Point Utility program group (or group where you installed
the configuration tools).
3. Windows will bring you to the Access Point Configuration & Firmware
Upgrade Utility screen.
From this screen, you will find the software firmware level, configure the Access
Point, and upgrade the Access Point’s firmware.
5.2 Setting the IP Address
If this is the first time you are connecting to the Access Point, the IP Address,
sub-net mask and ESSID (SSID) network name will need to be set up.
10
1. From within the Access Point Configuration & Firmware Upgrade Utility
screen, click the Configure button, then click the Get button.
2. In the left column, click on the Eth_IP_Address identifier. Then click the
Modify button.
3. Enter the IP Address, click OK.
4. Set up the values for the sub-net mask and the ESSID name.
5. Click the Set button.
Inhaltsverzeichnis
Beliebte Drahtloser Zugangspunkt Handbücher anderer Marken
D-Link
D-Link DWL-2100AP - AirPlus Xtreme G Bedienungsanleitung
Ubiquiti
Ubiquiti NanoStation NSM2 Bedienungsanleitung
Cisco
Cisco Aironet 1550 Series Bedienungsanleitung
Aruba
Aruba IAP-335 Bedienungsanleitung
Advantek Networks
Advantek Networks AWN-AP-54MR Bedienungsanleitung
IP-COM
IP-COM AP355 Bedienungsanleitung
Buffalo
Buffalo AirStation WLA-L11G Bedienungsanleitung
EnGenius
EnGenius EnStationACv2 Bedienungsanleitung
D-Link
D-Link DAP-3662 Bedienungsanleitung
xG Technology
xG Technology xMax CN1300 Bedienungsanleitung
Widelink
Widelink ezWave WAP-1100 Series Bedienungsanleitung
Edimax
Edimax CAP1200 Bedienungsanleitung
