I-Vac IVAC Pro Bedienungsanleitung

REMOTE USER GUIDE

www. switch.com

MBright Tools iVAC Inc.

5570 Jill Street.Box 557.Osgoode, Ontario Canada.K0A 2W0

Tel: 613 826 2200 .Fax: 613 826 3300.info@iVacSwitch.com

Table of Contents

1 Warnings

2 Physical Features

3 General Description

4 System Address

5 Tool Address

6 Replacing Batteries

 7Specications

8 Regulatory Approval

1 Warnings

Please read the operating instructions before use.

The iVAC Pro Remote is intended for indoor use

in dry locations only. Used batteries should be

disposed of in a safe manner.

2 Physical Features

DIP

Program

Switch

CR2032

Batteries

Belt Clip

3 General Description

The ‘iVAC Pro Remote’ operates in conjunction

with an ‘iVAC Pro Switch’ and enables a dust

collector to be controlled remotely, by means of a

manual operation.

When the ON button is pressed, a radio

frequency transmission is sent to the ‘iVAC Pro

Switch’ instructing it to turn on and provide

power to the dust collector. When the OFF button

is pressed, the power will be removed from the

dust collector.

To ensure consistent operation, it is

recommended that the buttons are operated for

one to two seconds.

The ‘iVAC Pro Remote’ can be programmed

by means of an internal DIP Program Switch to

operate on one of four System Addresses and

one of eight Tool Addresses, similar to an ‘iVAC

Pro Tool’. (Refer to iVAC Pro System User Guide

supplied with the iVAC Pro Switch)

The iVAC Pro Remote is housed in a plastic case

90mm x 70mm x 25mm.

An easily attached belt clip is also provided.

The rear cover is attached by three screws.

Removing the cover allows access to the

batteries and the DIP Program Switch.

This allows the batteries to be changed and

also to program address functions of the ‘iVAC

Pro Remote’ by means of the six position DIP

Program Switch.

There are two address functions, System Address

and Tool Address.

4 System Address

A System consists of an’ iVAC Pro Switch’ and

from one to eight iVAC Pro Tools or iVAC Pro

Remotes. There can be any mix of Tools or

Remotes.

By means of positions S1 and S2 of the DIP

Program Switch, the Remote can be assigned to

work on one of four System Addresses, A, B, C

or D.

The System Address enables up to four

Systems to operate independently while within

communication range of each other.

System Address

*factory setting

S1 S2

*A Off Off

B On Off

C Off On

D On On

5 Tool Address

Each iVAC Pro Remote or iVAC Pro Tool must

be assigned an independent one of eight Tool

Addresses. This information is used by the iVAC

Pro Switch to enable it to know the status of each

individual iVAC Pro Tool or iVAC Pro Remote in

the System. The Tool Address is set by means of

positions S3, S4 and S5 of the Program Switch.

S6 is not used.

Tool Address

*factory setting

S3 S4 S5

1 On Off Off

2 Off On Off

3 On On Off

4 Off Off On

5 On Off On

6 Off On On

*7 On On On

8 Off Off Off

6 Replacing the Batteries

The batteries have a useful life of 25,000

operations over a 3 year period.

To remove the batteries it is recommended to use

the tip of a pen or similar device and push from

the inside edge of the battery holder.

When replacing CR2032 batteries, both batteries

should be replaced at the same time. The

positive (+) side of the battery should face away

from the circuit board.

Andere Handbücher für iVAC Pro

Inhaltsverzeichnis

Sprachen:

Andere i-Vac Fernbedienung Handbücher

i-Vac

i-Vac iVAC Pro Bedienungsanleitung

Beliebte Fernbedienung Handbücher anderer Marken

Panasonic

Panasonic EUR7622KB0 Bedienungsanleitung

Bang & Olufsen

Bang & Olufsen Beo4 Bedienungsanleitung

Sunwave Tech.

Sunwave Tech. RemoteComm SRC-7000 Bedienungsanleitung

Multiplex

Multiplex PROFI TX 9 Bedienungsanleitung

One Remote

One Remote RMB4 Bedienungsanleitung

FUTABA

FUTABA 9ZAP - PART2 Bedienungsanleitung

HR Matic

HR Matic HR MULTI 3 Bedienungsanleitung

Yamaha

Yamaha ACC-GNRST-30-20 Bedienungsanleitung

EisSound

EisSound KBSOUND Bedienungsanleitung

Marantz

Marantz RC101 Bedienungsanleitung

Conrad

Conrad FS20 TC6 Bedienungsanleitung

Anritsu

Anritsu MP1777A Bedienungsanleitung

Niles

Niles WVC100 Fehlerbehebungshandbuch

RCA

RCA RCU1300 Bedienungsanleitung

Bang & Olufsen

Bang & Olufsen BEO6 Bedienungsanleitung

GE 94901 Bedienungsanleitung

Onbon

Onbon YQ1-75 Bedienungsanleitung

FUTABA

FUTABA R7108SB Montageanleitung