i3 International Ax46-series Bedienungsanleitung
Ax46/66-series
User Guide
Before attempting to connect or operate this product, read these instructions carefully.
Save this manual for future use.
CONTENTS
1. Warnings and operation notes.................................3
2. Unpacking..................................................................5
3. Installation................................................................6
4. Connecting to the SRX-Pro Server.........................10
5. Advanced Camera Setup.........................................18
6. Specifications..........................................................36
2
i3-TRNG-CAMS-Ax46/66.indd Rev. 130816
Ax46/66-series User Guide
COPYRIGHT ©2013 by i3 International, Inc. All rights reserved.
No part of this manual may be reproduced or transmitted in any form or by any
means, electronic or mechanical, including but not limited to, photocopying,
recording, or by any information storage or retrieval system, without the prior
written permission of the copyright owner and the publisher.
Annexxus is a registered trademark of i3 International Inc.
Disclaimer
This quick start guide is provided as is, without warranty of any kind, expressed or
implied, including but not limited to performance, merchantability, or fitness for any
particular purpose. Neither i3 International Inc. nor its dealers or distributors shall be
liable to any person or entity with respect to any liability, loss, or damage, caused or
alleged to have been caused directly or indirectly by this information.
Furthermore, i3 International Inc. reserves the right to revise this publication, and to
make changes to the content at any time, without notice.
FCC
This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and (2)
this device must accept any interference received, including interference that may
cause undesired operation.
Address:
i3 International Inc.
780 Birchmount Road, Unit 16
Scarborough, ON M1K 5H4
Canada
Contact us:
Tech Support: 1.877.877.7241
Web Site: www.i3international.com
Table of Contents
1. Warnings and operation notes
2. Unpacking
3. Installation
4. Connecting to SRX-Pro Server
5. Advanced Camera Setup
6. Specifications
3Rev. 130816i3-TRNG-CAMS-Ax46/66.indd
1. Warnings and operation notes
Please read this guide carefully before you install the camera. Keep this
guide for future reference.
Thank you for purchasing an i3 Ax46/66-series IR Outdoor Dome Camera.
If the system needs to be modified or repaired, contact a certified i3 International
Dealer/Installer. When serviced by unauthorized technician, the system warranty
will be voided. Should you have any problems or questions regarding our products,
contact your local i3 International Dealer/Installer.
1.1 Precautions
Installation and serving should be performed only by qualified and
experienced technicians to conform to all local codes and to maintain
your warranty.
When installing your Ax46/66 camera be sure to avoid:
• excessive heat, such as direct sunlight or heating appliances
• contaminants such as dust and smoke
• strong magnetic fields
• sources of powerful electromagnetic radiation such as radios or TV transmitters
• moisture and humidity
• areas with mechanical vibrations
• fluorescent lamps or objects that reflect light
• unstable light sources as this may cause flickering
• temperatures below -10° Celsius or 14° Fahrenheit and above 50° Celsius or
122° Fahrenheit for Ax46-series cameras, -25° Celsius or -13° Fahrenheit and
above 60° Celsius or 140° Fahrenheit for Ax66-series cameras
WARNING! The use of CSA certified/ UL Listed Class 2 power
adapter is required to ensure compliance.
WARNING! To reduce the risk of fire or electric shock, do not
expose the product to rain or moisture.
4
i3-TRNG-CAMS-Ax46/66.indd Rev. 130816
1.2 Power Supply
When using 12VDC, ensure the supplied voltage meets the power consumption
requirements of this camera before powering the camera on. Incorrect voltage may
cause irreparable damage to the video camera and will effectively void the camera
warranty. The camera also comes with the built-in PoE power support.
1.3 Cleaning
• For maximum optical clarity, the camera or lens must remain clean. Use a soft,
dry cloth to remove finger prints and dust from the dome cover.
• Use a blower to remove dust from the lens.
• Clean the body with a soft, dry cloth. If it is very dirty, use a cloth dampened
with a small quantity of neutral detergent, then wipe dry.
• Do not use volatile solvents such as alcohol, benzene, or thinners, as they may
damage the surface finish.
1.4 Servicing
To avoid electrical shock and to preserve the product warranty, DO NOT disassemble
the camera. Refer servicing to qualified personnel only.
WARNING! DO NOT connect both PoE and DC12V power connectors
at the same time. For DC power supply use, make sure the polarity is
correct to avoid malfunction and / or camera damage.
5Rev. 130816i3-TRNG-CAMS-Ax46/66.indd
2. Unpacking
Check that the items received match those listed on the order form and packing slip.
In addition to this manual and a fully assembled camera, the dome camera packing
box includes:
1. User Manual and Annexxus Finder CD x1
2. Guide Pattern sticker x1
3. Torx key x1
4. Plastic Anchor x3
5. Round Head Screw (Tapping type) x3
If any parts are missing or damaged, contact the dealer you purchased the camera
from.
Accessories (not to scale)
1
User Guide
IP Finder
25
4
3
Ceiling Mounting
Hole
Hole
HoleHole
6
i3-TRNG-CAMS-Ax46/66.indd Rev. 130816
3. Installation
Use the appropriate brackets and equipment to mount the camera. After installing
the camera, your network camera should be accessed from your local network.
3.1 Camera Parts and definitions
Mounting base
Horizontal stand
Vertical stand
Lower dome
Infrared lamp plate
Lens
Black liner
Safety rope
INDC12V
Cables
Power line
Network cable
Ø111
82.4
Ø79.1
Ø100.4
Unit: mm
Fig 3-1 - Parts and connectors
Fig 3-2 - Dimensions
7Rev. 130816i3-TRNG-CAMS-Ax46/66.indd
3.3 Mounting and adjusting camera
This is a dual axis camera and thus a ceiling mounting instead of a wall mounting is
recommended in order to provide the camera with an optimal view. When installing
on a wall, choose a location and field of view that is straight in front of the camera
as much as possible.
To mount the camera, do the following:
1. Prepare the surface for mounting. Drill screw holes on the surface with
the supplied camera mounting template. (Figure 3-3). If you need to route
cables from the bottom of the camera, cut a hole in the ceiling. Alternatively, if
necessary, cables can be routed through the opening on the side of the camera’s
mounting base. (Figure 3-4).
Fig 3-3 - Mounting template dimensions
Fig 3-4 - Camera base, side cable access
8
i3-TRNG-CAMS-Ax46/66.indd Rev. 130816
2. Disassemble camera prior to mounting. Loosen the set screws on the
camera with the supplied hex key to remove the lower dome.
3. Attach the camera to the surface. Fix the mounting base on the surface
with the supplied screws.
4. Adjust the camera’s pan and tilt position to obtain an optimal view-
ing angle. Loosen the tilt lock screws inside the camera. Adjust the tilting posi-
tion within 65 degrees and tighten the tilt lock screws. Rotate the black liner to
adjust the panning position within 360 degrees.
5. Reinstall the lower dome. Replace the lower dome onto the camera base
and tighten the screws.
Fig 3-5 - Attaching camera to wall
Tilt lock screw
Black liner
Fig 3-6 - Adjusting viewing angle
9Rev. 130816i3-TRNG-CAMS-Ax46/66.indd
Fig 3-7 - Reattach dome
10
i3-TRNG-CAMS-Ax46/66.indd Rev. 130816
4. Connecting to the SRX-Pro Server
4.1 Camera Connection Options
4.2 Hardware/Software Requirements
The following requirements must be met to achieve a successful network connection
with the Ax46/66-series IP camera.
SRX-Pro Server:
• i3 SRX-Pro Version 3.0 or higher
• Latest GiPi adapter is installed. GiPi adapters can be downloaded from i3 FTP
website. (Please contact i3 Technical Support for more information.)
• Windows XP, XPe, 7 Pro or 7e
• Internet Explorer Version 8.0 or later
• CPU: Intel Pentium Core 2 or higher
• Memory: 1GB or more
• VGA card--supporting Direct X 9.0 or above
Power Supply
Your camera requires a DC12V/PoE power supply. Make sure to use the correct
power supply before connecting to this network camera. Use a RJ45 network
connector to connect the camera to your computer or hub switch. Remember, If PoE
(Power over Ethernet) connector is used, an electrical cable is not required
Note: Camera damages resulted from improper power application are
i3 SRX-Pro Server
Crossover direct connection
LAN
i3 SRX-Pro Server
Via Gigabit Switch
Connection Type 1:
Connection Type 2:
Dieses Handbuch passt für folgende Modelle
8
Inhaltsverzeichnis
Andere i3 International Sicherheitskamera Handbücher
i3 International
i3 International Ax78R Bedienungsanleitung
i3 International
i3 International C-AX401C1MN Bedienungsanleitung
i3 International
i3 International Ax49D Bedienungsanleitung
i3 International
i3 International Am73 Bedienungsanleitung
i3 International
i3 International Ax45RM series Bedienungsanleitung
i3 International
i3 International Di721 Bedienungsanleitung
i3 International
i3 International Ax52 Series Bedienungsanleitung
i3 International
i3 International Ax40W2 series Bedienungsanleitung
i3 International
i3 International Ax63C Bedienungs- und Wartungsanleitung
i3 International
i3 International Ax63Z Series Bedienungsanleitung
i3 International
i3 International Ax45RM series Bedienungsanleitung
i3 International
i3 International H59B2 Bedienungsanleitung
i3 International
i3 International Am53 Bedienungsanleitung
i3 International
i3 International Ax73RM-series Bedienungsanleitung
i3 International
i3 International C-Di210 Bedienungsanleitung
i3 International
i3 International Ax51B Bedienungsanleitung
i3 International
i3 International Di721 Bedienungsanleitung
i3 International
i3 International Ax63Z Series Bedienungsanleitung
i3 International
i3 International M79 Bedienungsanleitung
i3 International
i3 International ANNEXXUS Ax41V1MVR Bedienungsanleitung
