IBM SP3001 Leitfaden
Power Supply Replacement Instructions
The following table lists the appliance models that are supported by the instructions in this document:
Product Model IBM®Part Number
IBM Security Network Protection XGS 7100 97Y1013
IBM Security SiteProtector™System SP 3001 46N5744
Note: The illustrations in this document might differ slightly from your appliance model.
Important: Before you proceed with these instructions, review the IBM Systems Safety Notices provided in
the IBM Media Terms and Conditions CD that is included with your appliance model.
CAUTION:
The power control button on the device and the power switch on the power supply do not turn off the
electrical current supplied to the device. The device also might have more than one power cord. To
remove all current from the device, ensure that all power cords are disconnected from the power
source.
CAUTION:
Never remove the cover on a power supply or any part that has the following label attached.
CAUTION:
Hazardous voltage, current, and energy levels are present inside any component that has this label
attached. There are no serviceable parts inside these components. If you suspect a problem with one
of these parts, contact a service technician.
Identifying the power supply
The back panel of the appliance contains the power supply units, as highlighted in yellow in Figure 1.
Identifying a failed power supply
The power supply unit uses an LED to indicate whether the unit is working as expected. The power
supply LED is located directly above the power cord connector, as shown in Figure 2:
The following table explains the different states of the power supply LED and suggests actions to solve
issues with the power supply:
Table 1. Different states of the power supply LED
Power supply LED status Possible condition Action
Off No power is going to the appliance,
or there is a problem with the power
source.
1. Check the power that is going to
the appliance.
2. Make sure that the power cord is
connected to a functioning power
source.
3. Turn off the appliance and then
turn the appliance back on.
4. If the problem remains, replace
the power supply.
Note: This condition is normal when
no power is present.
Flashes green once every second The power supply is operational, but
the appliance is in standby.
No further action needed.
Flashes red 3 times a second The power supply is faulty. Replace the power supply.
Solid green The power supply is operating
normally.
No further action needed.
Figure 1. Location of the power supply units on the back of the appliance
Figure 2. Location of the power supply LED
2
Replacing a failed power supply
Before you begin: When you replace a failed power supply, make sure that you do not unplug the power
supply unit that is working because this action disrupts service to the appliance.
Complete the following steps to replace a failed power supply:
1. Remove the failed power supply from the power supply bay by unplugging its power cord, pinching
the side clip, and then pulling the failed power supply from the bay, as shown in Figure 3.
Important: During normal operation, each power supply bay must contain a power supply for
adequate cooling.
2. Slide the replacement power supply into the bay until the retention latch clicks into place. Make sure
that the power supply connects firmly to the power supply connector.
3. Route the power cord for the new power supply through the power supply handle and through any
cable clamps on the back of the appliance to prevent the power cord from being accidentally pulled
out when you slide the appliance into and out of the rack.
4. Connect the power cord for the new power supply to the power cord connector on the power supply,
and then connect the power cord to a properly grounded electrical outlet.
What to do next
Make sure that the power supply LED is illuminated in solid green, which indicates that the unit is
operating correctly.
Figure 3. Removing the power supply from the back of the appliance
First edition: November 2014
© Copyright IBM Corporation 2014, 2015.
US Government Users Restricted Rights – Use, duplication or disclosure restricted by GSA ADP Schedule Contract
with IBM Corp.
Andere Handbücher für SP3001
4
Dieses Handbuch passt für folgende Modelle
3
Andere IBM Firewall Handbücher
IBM
IBM Proventia Management SiteProtector SP1001 Bedienungsanleitung
IBM
IBM GX7000 Series Bedienungsanleitung
IBM
IBM Proventia Management SiteProtector SP2001 Bedienungsanleitung
IBM
IBM Proventia Bedienungsanleitung
IBM
IBM 1G Bedienungsanleitung
IBM
IBM QRadar XGS 5200 Leitfaden
IBM
IBM DataPower XH40 Bedienungsanleitung
IBM
IBM GX7 Series Leitfaden
IBM
IBM SP3001 Bedienungsanleitung
IBM
IBM QRadar XGS 5200 Leitfaden
Beliebte Firewall Handbücher anderer Marken
Lanner electronics
Lanner electronics FW-7650 Series Bedienungsanleitung
Swisscom
Swisscom Internet Backup Bedienungsanleitung
SonicWALL
SonicWALL NSa 5700 Bedienungsanleitung
DPtech
DPtech FW1000 SERIES Bedienungsanleitung
FEITIAN
FEITIAN MultiPass FIDO Bedienungsanleitung
EBLOCKER
EBLOCKER PRO Bedienungsanleitung