IBM 2809 Bedienungsanleitung

AS/400e 170 or 250

2809 or 2824 LAN/WAN

Workstation Card

Instruction

Ve r s i o n 4

SENG-2809-04



AS/400e 170 or 250

2809 or 2824 LAN/WAN

Workstation Card

Instruction

Ve r s i o n 4

SENG-2809-04



Note

Before using this information and the product it supports, be sure to read the “Safety and Environmental Notices” on

page iii and the “Notices” on page 11.

Fifth Edition (July 2000)

This edition applies only to reduced instructions set computer (RISC) systems.

US Government Users Restricted Rights – Use, duplication or disclosure restricted by GSA ADP Schedule Contract

with IBM Corp.

Safety and Environmental Notices

Danger Notices

A danger notice calls attention to a situation that is potentially lethal or extremely

hazardous to people.

DANGER

An electrical outlet that is not correctly wired could place hazardous voltage

on metal parts of the system or the products that attach to the system. It is the

customer’s responsibility to ensure that the outlet is correctly wired and

grounded to prevent an electrical shock. (RSFTD201)

DANGER

To prevent a possible electrical shock when installing the system, ensure that

the power cords for all devices are unplugged before installing signal cables.

(RSFTD202)

DANGER

To prevent a possible electrical shock when adding or removing any devices

to or from the system, ensure that the power cords for those devices are

unplugged before the signal cables are connected or disconnected. If possible,

disconnect all power cords from the existing system before you add or

remove a device. (RSFTD203)

DANGER

To prevent a possible electrical shock during an electrical storm, do not

connect or disconnect cables or station protectors for communications lines,

display stations, printers, or telephones. (RSFTD003)

DANGER

To prevent a possible electrical shock from touching two surfaces with

different electrical grounds, use one hand, when possible, to connect or

disconnect signal cables. (RSFTD004)

Caution Notices

A caution notice calls attention to a situation that is potentially hazardous to

people because of some existing condition.

CAUTION:

Telecommunications Statement: This unit contains over-voltage circuits between

the ac power outlet and the unit. These circuits meet the standard limits

described in International Electrical Commission (IEC) 664, installation category

II. It is the customer’s responsibility to ensure that the power outlet meets the

standards of IEC 664, installation category II. (RSFTC214)

Laser Safety Information

CAUTION:

This product may contain a CD-ROM which is a class 1 laser product.

(RSFTC240)

Product Recycling and Disposal

Components of the system, such as structural parts and circuit cards, can be

recycled where recycling facilities exist. IBM does not currently collect and recycle

used IBM products from customers in the United States other than those products

that are involved in trade-in programs. Companies are available to disassemble,

reutilize, recycle, or dispose of electronic products. Contact an IBM account

representative for more information.

The system unit contains batteries and circuit boards with lead solder. Before you

dispose of this unit, these batteries and circuit boards must be removed and

discarded according to local regulations or recycled where facilities exist. This book

contains specific information on each battery type where applicable.

Battery Return Program

In the United States, IBM has established a collection process for reuse, recycling,

or proper disposal of used IBM batteries and battery packs. For information on

proper disposal of the batteries in this unit, please contact IBM at 1-800-426-4333.

Please have the IBM part number that is listed on the battery available when you

make your call. For information on battery disposal outside the United States,

contact your local waste disposal facility.

Environmental Design

The environmental efforts that have gone into the design of the system signify

IBM’s commitment to improve the quality of its products and processes. Some of

these accomplishments include the elimination of the use of Class I

ozone-depleting chemicals in the manufacturing process, reductions in

manufacturing wastes, and increased product energy efficiency. For more

information, contact an IBM account representative.

iv AS/400e 170 or 250 2809 or 2824 LAN/WAN Workstation Card V4R5

Installation Instructions

This feature is customer installed. It will take approximately 1 hour to install the

hardware. However, you may elect not to perform this feature installation yourself.

You may contact IBM or an Authorized Dealer to make arrangements for them to

perform the feature installation for a fee.

You need to allow additional time to complete your jobs, back up your system, IPL

your system, and verify your hardware configuration.

__ 1. When you use these instructions, you will do the following:

vRemove the system unit covers.

vInstall your new hardware.

vInstall covers.

vIPL your operating system.

vVerify your new hardware configuration.

__ 2. Some of the steps in these instructions may require a tool to remove the

screws. Use a medium-sized standard screwdriver or a 5.5 mm socket

wrench.

__ 3. Some of the pictures in these instructions may not look exactly like the

system unit that you have. However, the steps to perform the task are the

same.

__ 4. Before you begin:

vEnsure that you have a current backup of your operating system and

licensed programs. If you have backed up the operating system and

licensed programs since the last time you applied PTFs, that backup is

acceptable.

vEnsure that you take a few minutes to become familiar with these

instructions.

vIf there are incorrect, missing or visibly damaged parts, contact one of the

following:

–Your authorized dealer

–Point of purchase (For example, IBM Direct)

–IBM Rochester Manufacturing Automated Information Line (R-MAIL)

- 1-800-300-8751 (United States)

- 1-507-253-5242 (worldwide)

__ 5. Determine if there are any existing prerequisites before you install your new

feature. Go to this Web site and locate your feature number and OS/400

release and check the prerequisites.

http://as400service.ibm.com/s_dir/slkbase.NSF/

Then do the following to get to the Customer Install Features Prerequisites:

a. Select All Documents

b. Select Collapse

c. Select General Information

d. Select Offerings

e. Select Feature Prerequisites

f. Select Customer Install Features Prerequisites

When you have the following cards, install them in the sequence listed below.

vThe 2809 or 2824 LAN/WAN workstation card

vThe 285x or 2866 Integrated NetFinity cards

vAll other adapter cards

Getting Ready __ 1. Ensure that all jobs are complete.

__ 2. When all jobs are complete, type

pwrdwnsys *immed

on an AS/400 command line and press the Enter key.

Note: Should you encounter difficulties during the installation, contact your

authorized dealer or service provider.

__ 3. When the AS/400 is completely powered down, power off all PCs and

devices, such as printers and displays, that are connected to the system unit.

__ 4. Unplug any power cords, such as printers and displays, from electrical

outlets.

__ 5. Unplug the system unit power cord from the electrical outlet.

__ 6. Remove the system unit back cover by placing your hand near the bottom

of the cover and lifting up and out, (Figure 1).

Figure 1. Remove System Unit Back Cover

2AS/400e 170 or 250 2809 or 2824 LAN/WAN Workstation Card V4R5

Installing the 2809 or 2824 LAN/WAN Workstation Card

__ 1. The adapter card slots are E02 through E14 in the expansion unit,

(Figure 2). Slot E01 is not an available position.

__ 2. Remove the left side cover by removing the screws and sliding the cover

from front to back until it stops. Pull the cover out (Figure 3 on page 4).

Figure 2. Adapter Card Positions

Installation Instructions 3

Your system unit contains a battery that only trained personnel can

replace.

__ 3. CAUTION:

The battery is a lithium battery. Only trained service personnel may

replace this battery using the instructions in the Problem Analysis,

Repair, and Parts service manual. To avoid possible explosion, do not

burn or charge the battery. Exchange only with the IBM-approved part.

Discard the battery as instructed by local regulations. (RSFTC241)

__ 4. Attach the disposable wrist strap to prevent electrostatic discharge from

damaging a device. Figure 4 on page 5 shows an example of where to

attach the adhesive part of the foil to an unpainted surface.

Notes:

a. Follow the same precautions you would use without the wrist strap.

The 2209 Disposable Wrist Strap is for static control. It will not increase

nor decrease your risk of receiving electric shock when using or

working on electrical equipment.

b. Discard the wrist strap immediately and contact your dealer for a

replacement, if the disposable wrist strap appears damaged or cut off.

Do not continue until a new wrist strap is available.

c. Remove the liner from the copper foil at the end, when you unroll the

wrist strap.

d. Attach the copper foil to an exposed, unpainted metal surface on the

frame of the system unit (electrical ground).

Figure 3. Remove System Unit Side Cover

4AS/400e 170 or 250 2809 or 2824 LAN/WAN Workstation Card V4R5

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere IBM Server Handbücher

IBM

IBM Netfinity 3500 M10 Bedienungsanleitung

IBM

IBM 8480 - Eserver xSeries 205 Betriebsanleitung

IBM

IBM Power E1050 Bedienungsanleitung

IBM

IBM x3455 - System - 7984 Bedienungsanleitung

IBM

IBM x3500 - System - 7977 Bedienungsanleitung

IBM

IBM Power ESE 8412-EAD Bedienungsanleitung

IBM

IBM BladeCenter HS22 Bedienungsanleitung

IBM

IBM 7977D2U Bedienungsanleitung

IBM

IBM Power Systems Series Bedienungsanleitung

IBM

IBM IntelliStation R Pro Betriebsanleitung

IBM

IBM System x3620 M3 7376 Bedienungsanleitung

IBM

IBM H SERIES RS/6000 Bedienungsanleitung

IBM

IBM 8686 - Eserver xSeries 360 Betriebsanleitung

IBM

IBM System x3250 M3 Type 4251 Bedienungsanleitung

IBM

IBM BladeCenter HS22 Bedienungsanleitung

IBM

IBM BladeCenter HS22 Bedienungsanleitung

IBM

IBM SG24-4576-00 Kurzanleitung zur Einrichtung

IBM

IBM BladeCenter HS23 Bedienungsanleitung

IBM

IBM TotalStorage SAN140M Handbuch

IBM

IBM System x3100 M3 Bedienungsanleitung

IBM

IBM E Server i Series Bedienungsanleitung

IBM

IBM xSeries 365 Bedienungsanleitung

IBM

IBM p 655 series Bedienungsanleitung

IBM

IBM System x3620 M3 7376 Bedienungsanleitung

Beliebte Server Handbücher anderer Marken

HP AlphaServer ES47 Bedienungsanleitung

Dell

Dell PowerEdge R410 Bedienungsanleitung

PowerNAS

PowerNAS CMA Bedienungsanleitung

Supero

Supero FatTwin F617R3-FT Bedienungsanleitung

MSI

MSI P1-109N-L70 Bedienungsanleitung

Dell

Dell PowerEdge XE9640 Handbuch

Dell

Dell PS4100 Montageanleitung

EtroVISION

EtroVISION EV3151 Bedienungsanleitung

NEC

NEC Express5800/T110j Bedienungsanleitung

HP ProLiant Gen9 Bedienungsanleitung

Compaq

Compaq ProLiant 3000 Handbuch

Dell

Dell PowerEdge 3YPMN Bedienungsanleitung

iRobo

iRobo IPC2U Bedienungsanleitung

Nortel

Nortel 1000 Con?guration guide Bedienungsanleitung

Asus

Asus AP7500 Bedienungs- und Wartungshandbuch

Avid Technology

Avid Technology AirSpeed 5000 Bedienungsanleitung

HP Integrity rx2600 Installationsanleitung

Milestone

Milestone Husky IVO 350T Bedienungsanleitung