IBM E Server i Series Bedienungsanleitung

iSeries

Setting Up Your

0578, 5074, 5078 or 5079

Expansion Unit

Version 5

SA41-5149-02

ERserver



iSeries

Setting Up Your

0578, 5074, 5078 or 5079

Expansion Unit

Version 5

SA41-5149-02

ER s e r v e r



Note

Before using this information and the product it supports, be sure to read the information in

“Safety and Environmental Notices” on page v and “Notices” on page 51.

Third Edition (August 2002)

This edition applies only to reduced instruction set computer (RISC)) systems.

US Government Users Restricted Rights – Use, duplication or disclosure restricted by GSA ADP Schedule Contract

with IBM Corp.

Contents

Safety and Environmental Notices . . . v

Danger Notices .............v

Caution Notices .............v

Laser Safety Information .........vi

Product Recycling and Disposal.......vi

Battery Return Program .........vi

Environmental Design ..........vi

About Setting up your 0578, 5074, 5078

or 5079 Expansion Unit (SA41–5149) . . vii

Who should read this book .........vii

Prerequisite and related information ......vii

iSeries Navigator ............vii

How to send your comments ........viii

Chapter 1. Preparing to set up your 5074

or 5079 Expansion Unit ........1

Hardwarerequirements...........1

Site planning considerations for the 5079 .....1

Identifying HSL and SPCN Cables ......2

Planning your cable layout ........2

Configurationrules...........5

Powering down your iSeries system unit .....6

Chapter 2. Setting up your 5074

expansion unit ............9

Connecting your 5074 directly to your system unit . 9

Connecting your 5074 to another expansion unit . . 10

Connecting your 5074 at the beginning of a loop 11

Connecting your 5074 to the middle of a loop . . 13

Connecting your 5074 to the end of a loop . . . 14

Chapter 3. Setting up your 0578

expansion unit ...........15

Connecting your 0578 directly to your system unit 15

Chapter 4. Setting up your 5079

Expansion Unit ...........19

Connecting your 5079 directly to your system unit 19

Connecting your 5079 to another expansion unit . . 22

Connecting your 5079 at the beginning of a loop 22

Connecting your 5079 in the middle of a loop . . 24

Connecting your 5079 to the end of a loop . . . 25

Chapter 5. Completing your installation 27

Chapter 6. Verifying Your New

Configuration ............29

Appendix A. Removing the back covers 31

5075 and 820 back cover ..........31

5074, 830 and 890 back cover ........31

5079 and 840 back cover ..........32

Accessing units in a rack ..........34

Appendix B. Connector Locations . . . 35

820 HSL connector locations .........35

830 HSL connector locations .........36

840 HSL connector locations .........37

890 HSL connector locations .........38

5079 connector locations ..........39

5074 connector locations ..........40

5075 connector locations ..........41

5078 connector locations ..........41

Appendix C. System unit control panel 43

Appendix D. Cabling rules for systems

with a migration unit or the 9079 and

9094 expansion unit .........45

Notices ..............51

Trademarks..............52

Electronic Emission Notices .........53

Federal Communications Commission (FCC)

Statement..............53

Electronic Emission Notices .........54

Federal Communications Commission (FCC)

Statement..............54

iv Setting up your 0578, 5074, 5078 or 5079 Expansion Unit V5R2

Safety and Environmental Notices

Danger Notices

A danger notice calls attention to a situation that is potentially lethal or extremely

hazardous to people.

DANGER

An electrical outlet that is not correctly wired could place hazardous voltage

on metal parts of the system or the products that attach to the system. It is the

customer’s responsibility to ensure that the outlet is correctly wired and

grounded to prevent an electrical shock. (RSFTD201)

DANGER

To prevent a possible electrical shock when installing the system, ensure that

the power cords for all devices are unplugged before installing signal cables.

(RSFTD202)

DANGER

To prevent a possible electrical shock when adding or removing any devices

to or from the system, ensure that the power cords for those devices are

unplugged before the signal cables are connected or disconnected. If possible,

disconnect all power cords from the existing system before you add or

remove a device. (RSFTD203)

DANGER

To prevent a possible electrical shock during an electrical storm, do not

connect or disconnect cables or station protectors for communications lines,

display stations, printers, or telephones. (RSFTD003)

DANGER

To prevent a possible electrical shock from touching two surfaces with

different electrical grounds, use one hand, when possible, to connect or

disconnect signal cables. (RSFTD004)

Caution Notices

A caution notice calls attention to a situation that is potentially hazardous to

people because of some existing condition.

CAUTION:

Telecommunications Statement: This unit contains over-voltage circuits between

the ac power outlet and the unit. These circuits meet the standard limits

described in International Electrical Commission (IEC) 664, installation category

II. It is the customer’s responsibility to ensure that the power outlet meets the

standards of IEC 664, installation category II. (RSFTC214)

Laser Compliance

All Lasers are certified in the U.S. to conform to the requirements of DHHS 21 CFR

Subchapter J for class 1 laser products. Outside the U.S., they are certified to be in

compliance with the IEC 825 (first edition 1984) and as a class 1 laser product.

Consult the label on each part for laser certification numbers and approval

information.

Laser Safety Information

CAUTION:

This product may contain a CD-ROM which is a class 1 laser product.

(RSFTC240)

CAUTION:

All IBM laser modules are designed so that there is never any human access to

laser radiation above a class 1 level during normal operation, user maintenance,

or prescribed service conditions. Data processing environments can contain

equipment transmitting on system links with laser modules that operate at

greater than class 1 power levels. For this reason, never look into the end of an

optical fiber cable or open receptacle. Only trained service personnel should

perform the inspection or repair of optical fiber cable assemblies and

receptacles. (RSFTC243)

Product Recycling and Disposal

Components of the system, such as structural parts and circuit cards, can be

recycled where recycling facilities exist. IBM does not currently collect and recycle

used IBM products from customers in the United States other than those products

that are involved in trade-in programs. Companies are available to disassemble,

reutilize, recycle, or dispose of electronic products. Contact an IBM account

representative for more information.

The system unit contains batteries and circuit boards with lead solder. Before you

dispose of this unit, these batteries and circuit boards must be removed and

discarded according to local regulations or recycled where facilities exist. This book

contains specific information on each battery type where applicable.

Battery Return Program

In the United States, IBM has established a collection process for reuse, recycling,

or proper disposal of used IBM batteries and battery packs. For information on

proper disposal of the batteries in this unit, please contact IBM at 1-800-426-4333.

Please have the IBM part number that is listed on the battery available when you

make your call. For information on battery disposal outside the United States,

contact your local waste disposal facility.

Environmental Design

The environmental efforts that have gone into the design of the system signify

IBM’s commitment to improve the quality of its products and processes. Some of

these accomplishments include the elimination of the use of Class I

ozone-depleting chemicals in the manufacturing process, reductions in

manufacturing wastes, and increased product energy efficiency. For more

information, contact an IBM account representative.

vi Setting up your 0578, 5074, 5078 or 5079 Expansion Unit V5R2

About Setting up your 0578, 5074, 5078 or 5079 Expansion

Unit (SA41–5149)

This book contains installation about setting up your expansion unit. You may elect

to set up your new expansion unit yourself. It will take approximately one to three

hours to install the hardware

You also may elect not to install the expansion unit yourself. You may contact IBM

or an authorized dealer to make arrangements for them to install it for a fee.

Who should read this book

You should be familiar with the iSeries system, display, and keyboards. You should

also know how to power down the system and perform a system initial program

load. You should also know how to power down system peripherals such as

printers, monitors, and PCs.

Prerequisite and related information

Use the iSeries Information Center as your starting point for looking up iSeries

technical information.

You can access the Information Center two ways:

vFrom the following Web site:

http://www.ibm.com/eserver/iseries/infocenter

vFrom CD-ROMs that ship with your Operating System/400 order:

iSeries Information Center, SK3T-4091-02. This package also includes the PDF

versions of iSeries manuals, iSeries Information Center: Supplemental Manuals,

SK3T-4092-01, which replaces the Softcopy Library CD-ROM.

The iSeries Information Center contains advisors and important topics such as

Java, TCP/IP, Web serving, secured networks, logical partitions, clustering, CL

commands, and system application programming interfaces (APIs). It also includes

links to related IBM Redbooks and Internet links to other IBM Web sites such as

the Technical Studio and the IBM home page.

With every new hardware order, you receive the iSeries Setup and Operations

CD-ROM, SK3T-4098-01. This CD-ROM contains IBM Eserver iSeries Access for

Windows and the EZ-Setup wizard. iSeries Access offers a powerful set of client

and server capabilities for connecting PCs to iSeries servers. The EZ-Setup wizard

automates many of the iSeries setup tasks.

iSeries Navigator

IBM iSeries Navigator is a powerful graphical interface for managing your iSeries

servers. iSeries Navigator functionality includes system navigation, configuration,

planning capabilities, and online help to guide you through your tasks. iSeries

Navigator makes operation and administration of the server easier and more

productive and is the only user interface to the new, advanced features of the

OS/400 operating system. It also includes Management Central for managing

multiple servers from a central system.

You can find more information on iSeries Navigator in the iSeries Information

Center and at the following Web site:

http://www.ibm.com/eserver/iseries/navigator/

How to send your comments

Your feedback is important in helping to provide the most accurate and

high-quality information. If you have any comments about this book or any other

iSeries documentation, fill out the readers’comment form at the back of this book.

vIf you prefer to send comments by mail, use the readers’comment form with the

address that is printed on the back. If you are mailing a readers’comment form

from a country other than the United States, you can give the form to the local

IBM branch office or IBM representative for postage-paid mailing.

vIf you prefer to send comments by FAX, use either of the following numbers:

–United States, Canada, and Puerto Rico: 1-800-937-3430

–Other countries: 1-507-253-5192

vIf you prefer to send comments electronically, use one of these e-mail addresses:

–Comments on books:

[email protected]

–Comments on the iSeries Information Center:

[email protected]

Be sure to include the following:

vThe name of the book or iSeries Information Center topic.

vThe publication number of the book.

vThe page number or topic of a book to which your comment applies.

viii Setting up your 0578, 5074, 5078 or 5079 Expansion Unit V5R2

Andere Handbücher für E Server i Series

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere IBM Server Handbücher

IBM

IBM eServer xSeries 205Type 8480 Bedienungsanleitung

IBM

IBM PS700 Installationsanleitung

IBM

IBM Power Systems Series Bedienungsanleitung

IBM

IBM 8648 - eServer xSeries 226 Bedienungsanleitung

IBM

IBM System x3500 M2 Type 7839 Bedienungsanleitung

IBM

IBM 8670 - Eserver xSeries 345 Bedienungsanleitung

IBM

IBM Netfinity 7600 Bedienungsanleitung

IBM

IBM x3800 - System - 8865 Bedienungsanleitung

IBM

IBM ISERIES SC41-5210-04 Bedienungsanleitung

IBM

IBM System x3950 X6 Bedienungsanleitung

IBM

IBM System x3530 M4 Bedienungsanleitung

IBM

IBM HS40 - BladeCenter - 8839 Betriebsanleitung

IBM

IBM 270 Bedienungsanleitung

IBM

IBM Power System E880C Gebrauchs- und Pflegehandbuch

IBM

IBM 88632SU Bedienungsanleitung

IBM

IBM NetVista N2200l Bedienungsanleitung

IBM

IBM S812L Bedienungsanleitung

IBM

IBM z13s Kurzanleitung

IBM

IBM x3655 - System - 7985 Bedienungsanleitung

IBM

IBM System x3620 M3 7376 Bedienungsanleitung

IBM

IBM NETFINITY 4000R Bedienungsanleitung

IBM

IBM Power System 8335-GTW Bedienungsanleitung

IBM

IBM iSeries Series Administratorhandbuch

IBM

IBM 5100 Bedienungsanleitung

Beliebte Server Handbücher anderer Marken

HP AlphaServer ES47 Bedienungsanleitung

Dell

Dell PowerEdge R410 Bedienungsanleitung

PowerNAS

PowerNAS CMA Bedienungsanleitung

Supero

Supero FatTwin F617R3-FT Bedienungsanleitung

MSI

MSI P1-109N-L70 Bedienungsanleitung

Dell

Dell PowerEdge XE9640 Handbuch

Dell

Dell PS4100 Montageanleitung

EtroVISION

EtroVISION EV3151 Bedienungsanleitung

NEC

NEC Express5800/T110j Bedienungsanleitung

HP ProLiant Gen9 Bedienungsanleitung

Compaq

Compaq ProLiant 3000 Handbuch

Dell

Dell PowerEdge 3YPMN Bedienungsanleitung

iRobo

iRobo IPC2U Bedienungsanleitung

Nortel

Nortel 1000 Con?guration guide Bedienungsanleitung

Asus

Asus AP7500 Bedienungs- und Wartungshandbuch

Avid Technology

Avid Technology AirSpeed 5000 Bedienungsanleitung

HP Integrity rx2600 Installationsanleitung

Milestone

Milestone Husky IVO 350T Bedienungsanleitung