IBM Enterprise Server H80 Series Bedienungsanleitung

RS/6000 Enterprise Server Model H80

~pSeries 660 Models 6H0 and 6H1

User’s Guide

SA38-0565-03

IBM

Fourth Edition (June 2001)

Before using this information and the product it supports, read the information in “Safety Notices” on page ix,

“Appendix A. Environmental Notices” on page 129, and “Appendix B. Notices” on page 131.

A reader’s comment form is provided at the back of this publication. If the form has been removed, address comments

to Publications Department, Internal Zip 9561, 11400 Burnet Road, Austin, Texas 78758-3493. To send comments

electronically, use this commercial internet address: [email protected]. Any information that you supply may be

used without incurring any obligation to you.

Note to U.S. Government Users -- Documentation related to restricted rights -- Use, duplication or disclosure is subject

to restrictions set forth in GSA ADP Schedule Contract with IBM Corp.

Contents

Safety Notices ........................ix

Rack Safety Instructions .....................ix

Electrical Safety........................ix

Laser Safety Information .....................xi

Laser Compliance ......................xi

Data Integrity and Verification ..................xiii

About This Book.......................xv

ISO 9000..........................xv

Online Publications ......................xv

Related Publications ......................xv

Ergonomic Information .....................xvi

Trademarks.........................xvi

Chapter 1. Introducing the RS/6000 Enterprise Server Model H80 ......1

Chapter 2. Using the RS/6000 Enterprise Server Model H80 ........3

Operator Panel ........................3

Scrolling Ball Indicator......................3

Powering Off and Powering On the System...............3

Powering Off the System ....................3

Powering On the System ....................4

Powering Off and Powering On the System Using the Service Processor ....4

POST Indicators........................4

POST Keys .........................5

1Key..........................5

5Key..........................5

6Key..........................5

8Key..........................6

Console Strategy .......................6

Reading the I/O Drawer Operator Panel Display .............7

Checkpoints ........................7

Using the Keyboards ......................7

Using the Three-Button Mouse ...................8

Handling the Mouse Correctly ..................8

Caring for the Mouse .....................8

Cleaning the Mouse .....................9

Using the 3.5-Inch Diskette Drive..................10

Write-Protecting 3.5-Inch Diskettes ................10

Loading and Unloading the 3.5-Inch Diskette .............11

Using the CD-ROM Drive ....................11

Loading the CD-ROM Drive ..................12

Unloading the CD-ROM Drive ..................12

Cleaning the CD-ROM Drive ..................12

Emergency Eject ......................12

Using the Service Processor and Service Agent Features .........14

iii

Service Processor......................14

Electronic Service Agent ...................15

Chapter 3. Using the Service Processor...............17

Service Processor Menus ....................18

Accessing the Service Processor Menus Locally............18

Accessing the Service Processor Menus Remotely ...........18

Saving and Restoring Service Processor Settings ...........18

Menu Inactivity .......................19

General User Menu ......................19

Privileged User Menus .....................20

MainMenu........................20

Service Processor Setup Menu .................22

Passwords ........................23

System Power Control Menu ..................26

System Information Menu ...................29

Memory Riser Card 1 Memory DIMM Locations for Service Processor Menus 34

Memory Riser Card 2 Memory DIMM Locations for Service Processor Menus 34

Processor Card Memory DIMM Locations for Service Processor Menus ....35

Language Selection Menu ...................36

Call-In/Call-Out Setup Menu ..................38

Modem Configuration Menu ..................39

Serial Port Selection Menu ...................40

Serial Port Speed Setup Menu .................40

Telephone Number Setup Menu .................41

Call-Out Policy Setup Menu ..................42

Customer Account Setup Menu .................43

Service Processor Procedures in Service Mode .............43

Service Processor Functions ...................44

System Power-On Methods ...................45

Service Processor Reboot/Restart Recovery ..............46

Boot (IPL) Speed ......................46

Failure During Boot Process ..................46

Failure During Normal System Operation ..............46

Service Processor Reboot/Restart Policy Controls ...........46

System Firmware Updates ....................48

General Information on System Firmware Updates ...........48

Determining the Level of Firmware on the System ...........49

System Firmware Update Using a Locally Available Image ........49

Updating System Firmware From the Service Processor Menus ......50

Updating System Firmware from the AIX Service Aids ..........50

Updating System Firmware from the AIX Command Line .........50

Recovery Mode ......................50

Configuring and Deconfiguring Processors or Memory...........51

Run-Time CPU Deconfiguration (CPU Gard) .............52

Service Processor System Monitoring - Surveillance ...........52

System Firmware Surveillance..................52

Operating System Surveillance .................52

Call-Out (Call-Home) ......................53

Console Mirroring .......................55

iv User’s Guide

System Configuration ....................55

Service Processor Error Log ...................56

LCD Progress Indicator Log ...................57

Service Processor Operational Phases ................58

Pre-Standby Phase .....................58

Standby Phase.......................58

Bring-Up Phase ......................59

Run-Time Phase ......................60

Chapter 4. Using System Management Services............61

Password Utilities ......................62

Display Error Log ......................63

Remote Initial Program Load Setup ................63

SCSI Utilities .......................67

Select Console.......................67

MultiBoot.........................68

Select Language ......................71

OK Prompt ........................71

Exiting System Management Services ...............71

Chapter 5. Using the Online and Standalone Diagnostics ........73

Online and Standalone Diagnostics Operating Considerations ........73

Selecting a Console Display ..................73

Identifying the Terminal Type to the Diagnostics ............73

Undefined Terminal Types ...................74

Running Online Diagnostics ..................74

Running Standalone Diagnostics .................74

Running the Diagnostics from a TTY Terminal ............75

Required Diagnostic Attributes..................75

Additional Communication Attributes................77

Additional Keyboard Attributes..................77

Additional Printer Attributes...................78

Online Diagnostics Modes of Operation ...............79

Service Mode .......................79

Running the Online Diagnostics in Service Mode ...........79

Concurrent Mode ......................80

Running the Online Diagnostics in Concurrent Mode ..........80

Maintenance Mode .....................81

Running the Online Diagnostics in Maintenance Mode..........81

Standalone Diagnostic Operation..................81

Running the Standalone Diagnostics ...............81

Chapter 6. Introducing Tasks and Service Aids ............83

Tasks ...........................83

Add Resource to Resource List ..................84

AIX Shell Prompt .......................85

Analyze Adapter Internal Log ...................85

Backup and Restore Media....................85

Certify Media ........................85

Change Hardware Vital Product Data ................86

Contents v

Configure Dials and LPF Keys...................86

Configure Reboot Policy.....................87

Configure Remote Maintenance Policy ................88

Configure Ring Indicate Power-On Policy ...............90

Configure Surveillance Policy ...................90

Create Customized Configuration Diskette...............91

Delete Resource from Resource List ................91

Disk Maintenance .......................91

DisktoDiskCopy......................91

Display/Alter Sector .....................92

Display Configuration and Resource List ...............92

Display Firmware Device Node Information ..............92

Display Hardware Error Report ..................93

Display Hardware Vital Product Data ................93

Display Machine Check Error Log .................93

Display Microcode Level.....................93

Display or Change Bootlist ....................93

Display or Change Diagnostic Run-Time Options ............94

Display Previous Diagnostic Results.................94

Display Resource Attributes ...................95

Display Service Hints......................95

Display Software Product Data ..................95

Display System Environmental Sensors ...............96

Examples ........................97

Display Test Patterns......................97

Download Microcode ......................97

Download Microcode to PCI SCSI RAID Adapter ...........98

Download Microcode to Disk Drive Attached to a PCI SCSI RAID Adapter . . . 98

Download Microcode to a PCI FC-AL Adapter ............98

Download Microcode to Other Devices ...............98

Fibre Channel RAID Service Aid ..................98

Flash SK-NET FDDI Firmware...................99

Format Media ........................99

Hardfile Attached to SCSI Adapter (non-RAID) ............99

Hardfile Attached to PCI SCSI RAID Adapter ............101

Optical Media .......................101

Diskette Format ......................101

Generic Microcode Download ..................102

Hot Plug Task........................102

PCI Hot Plug Manager ....................103

SCSI Hot Swap Manager ...................104

RAID Hot Plug Devices ...................105

Local Area Network Analyzer...................106

Log Repair Action ......................106

Periodic Diagnostics .....................106

PCI RAID Physical Disk Identify..................106

Process Supplemental Media ..................107

Run Diagnostics .......................107

Run Error Log Analysis ....................107

Run Exercisers .......................107

vi User’s Guide

Exerciser Commands (CMD)..................107

Abbreviations .......................108

Memory Exerciser .....................108

Save or Restore Hardware Management Policies ............109

SCSI Bus Analyzer ......................109

SCSD Tape Drive Service Aid ..................110

Spare Sector Availability ....................111

SSA Service Aid .......................111

Update Disk-Based Diagnostics ..................111

Update System or Service Processor Flash ..............111

Attention ........................112

7135 RAIDiant Array Service Aid .................113

Examples ........................113

7318 Serial Communications Network Server Service Aid .........114

Chapter 7. Using the System Verification Procedure ..........115

Step 1. Considerations before Running This Procedure ..........115

Step 2. Loading the Diagnostics..................115

Step 3. Running System Verification ................116

Step 4. Additional System Verification ................116

Step 5. Stopping the Diagnostics .................116

Chapter 8. Hardware Problem Determination ............119

Problem Determination Using the Standalone or Online Diagnostics ......119

Problem Determination When Unable to Load Diagnostics .........124

Appendix A. Environmental Notices................129

Product Recycling and Disposal..................129

Environmental Design .....................129

Unit Emissions.......................129

Appendix B. Notices .....................131

Appendix C. Service Processor Setup and Test ...........133

Service Processor Setup Checklist .................133

Testing the Setup ......................134

Testing Call-In ......................134

Testing Call-Out ......................134

Serial Port Configuration ...................135

Appendix D. Modem Configurations ...............137

Sample Modem Configuration Files ................137

Generic Modem Configuration Files ...............137

Specific Modem Configuration Files ...............137

Configuration File Selection ...................138

Examples for Using the Generic Sample Modem Configuration Files ....140

Customizing the Modem Configuration Files.............140

IBM 7852-400 DIP Switch Settings................141

Xon/Xoff Modems .....................141

Ring Detection ......................141

Contents vii

Terminal Emulators .....................142

Recovery Procedures ....................142

Transfer of a Modem Session ..................142

Recovery Strategy .....................143

Prevention Strategy .....................144

Modem Configuration Sample Files ................145

Sample File modem_m0.cfg ..................145

Sample File modem_m1.cfg ..................148

Sample File modem_z.cfg...................151

Sample File modem_z0.cfg ..................154

Sample File modem_f.cfg ...................157

Sample File modem_f0.cfg ..................160

Sample File modem_f1.cfg ..................163

Index ..........................167

viii User’s Guide

Safety Notices

danger

notice indicates the presence of a hazard that has the potential of causing

death or serious personal injury.

Danger

notices appear on the following pages:

caution

notice indicates the presence of a hazard that has the potential of causing

moderate or minor personal injury.

Caution

notices appear on the following pages:

vxi

v11

For a translation of the safety notices contained in this book, see the

System Unit

Safety Information

, order number SA23-2652.

Rack Safety Instructions

vDo not install this unit in a rack where the internal rack ambient temperatures will

exceed 40 degrees C.

vDo not install this unit in a rack where the air flow is compromised. Any side, front or

back of the unit used for air flow through the unit must not be in indirect contact with

the rack.

vCare should be taken to ensure that a hazardous condition is not created due to

uneven mechanical loading when installing this unit in a rack. If the rack has a

stabilizer it must be firmly attached before installing or removing this unit.

vThis unit requires 3 amps with an input of 200-240 V ac power, or it can have -48V

dc power. Consideration should be given to the connection of the equipment to the

supply circuit so that overloading of circuits does not compromise the supply wiring

or overcurrent protection.

vAn electrical outlet that is not correctly wired could place hazardous voltage on the

metal parts of the system or the devices that attach to the system. It is the

responsibility of the customer to ensure that the outlet is correctly wired and

grounded to prevent an electrical shock.

Electrical Safety

Observe the following safety instructions anytime you are connecting or disconnecting

devices attached to the workstation.

DANGER

An electrical outlet that is not correctly wired could place hazardous voltage

on metal parts of the system or the devices that attach to the system. It is the

responsibility of the customer to ensure that the outlet is correctly wired and

grounded to prevent an electrical shock.

Before installing or removing signal cables, ensure that the power cables for

the system unit and all attached devices are unplugged.

When adding or removing any additional devices to or from the system,

ensure that the power cables for those devices are unplugged before the

signal cables are connected. If possible, disconnect all power cables from the

existing system before you add a device.

Use one hand, when possible, to connect or disconnect signal cables to

prevent a possible shock from touching two surfaces with different electrical

potentials.

During an electrical storm, do not connect cables for display stations, printers,

telephones, or station protectors for communications lines.

CAUTION:

This product is equipped with a three-wire power cable and plug for the user’s

safety. Use this power cable in conjunction with a properly grounded electrical

outlet to avoid electrical shock.

DANGER

To prevent electrical shock hazard, disconnect the power cable from the

electrical outlet before relocating the system.

CAUTION:

This unit has more than one power supply cord. To reduce the risk of electrical

shock, disconnect two power supply cords before servicing.

xUser’s Guide

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere IBM Server Handbücher

IBM

IBM Power System System E950 Bedienungsanleitung

IBM

IBM 867372X Betriebsanleitung

IBM

IBM BladeCenter HS23 Bedienungsanleitung

IBM

IBM Netfinity 3500 M20 Bedienungsanleitung

IBM

IBM System x3250 Bedienungsanleitung

IBM

IBM x3350 - System - 4192 Bedienungsanleitung

IBM

IBM E Server 440 x Series Betriebsanleitung

IBM

IBM F80 Bedienungsanleitung

IBM

IBM System x3250 M5 Bedienungsanleitung

IBM

IBM eServer xSeries 226Type 8648 Bedienungsanleitung

IBM

IBM System x3690 X5 Bedienungsanleitung

IBM

IBM System x3620 M3 7376 Bedienungsanleitung

IBM

IBM System x3650 M2 Type 7947 Bedienungsanleitung

IBM

IBM 71455RU Bedienungsanleitung

IBM

IBM S822LC Bedienungsanleitung

IBM

IBM N Series Kurzanleitung

IBM

IBM eServer BladeCenter HS20Type 8832 Betriebsanleitung

IBM

IBM x3850 X5 Bedienungsanleitung

IBM

IBM 88743RU - System x3950 E Bedienungsanleitung

IBM

IBM System x3530 M4 Bedienungsanleitung

IBM

IBM System x3650 M4 Type 7915 Bedienungsanleitung

IBM

IBM System x3500 M4 Bedienungsanleitung

IBM

IBM 8832L1X Betriebsanleitung

IBM

IBM NetVista Montageanleitung

Beliebte Server Handbücher anderer Marken

HP AlphaServer ES47 Bedienungsanleitung

Dell

Dell PowerEdge R410 Bedienungsanleitung

PowerNAS

PowerNAS CMA Bedienungsanleitung

Supero

Supero FatTwin F617R3-FT Bedienungsanleitung

MSI

MSI P1-109N-L70 Bedienungsanleitung

Dell

Dell PowerEdge XE9640 Handbuch

Dell

Dell PS4100 Montageanleitung

EtroVISION

EtroVISION EV3151 Bedienungsanleitung

NEC

NEC Express5800/T110j Bedienungsanleitung

HP ProLiant Gen9 Bedienungsanleitung

Compaq

Compaq ProLiant 3000 Handbuch

Dell

Dell PowerEdge 3YPMN Bedienungsanleitung

iRobo

iRobo IPC2U Bedienungsanleitung

Nortel

Nortel 1000 Con?guration guide Bedienungsanleitung

Asus

Asus AP7500 Bedienungs- und Wartungshandbuch

Avid Technology

Avid Technology AirSpeed 5000 Bedienungsanleitung

HP Integrity rx2600 Installationsanleitung

Milestone

Milestone Husky IVO 350T Bedienungsanleitung