IBM EServer iSeries 8 Series Bedienungsanleitung

iSeries 270 and 8xx

Upgrading the System Unit from

Operations Console to Twinaxial

Console (5540)

Version 5

ERserver



iSeries 270 and 8xx

Upgrading the System Unit from

Operations Console to Twinaxial

Console (5540)

Version 5

ER s e r v e r



US Government Users Restricted Rights – Use, duplication or disclosure restricted by GSA ADP Schedule Contract

with IBM Corp.

Upgrade Operations Console to twinaxial console

Before you begin

This feature is customer installable. You can elect not to do this installation

yourself. You may contact IBM

or an authorized dealer to make arrangements for

them to perform the feature installation for a fee.

You need to allow additional time to complete your jobs, back up your system,

perform an initial program load (IPL) of your system, and verify your hardware

configuration.

When you use these instructions, you may do some of the following:

vRemove the system unit covers.

vInstall your new hardware.

vInstall covers.

vPerfrom an IPL of your operating system.

vVerify your new hardware configuration.

Some of the figures in these instructions may not look exactly like the system unit

that you have. However, the steps to perform the task are the same.

__ 1. Ensure that you have a current backup of your system (including operating

systems, licensed programs, and data).

__ 2. Ensure that you take a few minutes to become familiar with these

instructions.

__ 3. If there are incorrect, missing, or visibly damaged parts, contact one of the

following:

vYour authorized dealer

vIBM Rochester Manufacturing Automated Information Line (R-MAIL)

–1-800-300-8751 (United States)

–1-507-253-5242 (worldwide)

__ 4. If you encounter difficulties during the installation, contact your authorized

service provider or your authorized dealer.

__ 5. Determine if there are any existing PTF prerequisites before you install your

new feature. Go to the following Web site:

http://www-912.ibm.com/supporthome.nsf/document/10000051

a. Select All Documents.

b. Select Collapse.

c. Select General Information.

d. Select Offerings.

e. Select Feature Prerequisites.

f. Select Customer Install Features Prerequisites.

g. Locate your feature number and OS/400

release, and check the

prerequisites.

Power off the system unit

__ 1. Ensure that all jobs are complete.

__ 2. When all jobs are complete, type pwrdwnsys *immed on a command line and

press Enter.

Note: Should you encounter difficulties during the installation, contact your

authorized dealer or service provider.

__ 3. When the unit is completely powered down, disconnect all PCs from the

system unit. Power off all devices, such as printers and displays, that are

connected to the system unit.

__ 4. Unplug any power cords, such as printers and displays, from electrical

outlets.

__ 5. Unplug the system-unit power cord and any attached expansion-unit power

cords from the electrical outlet.

__ 6. Refer to “Removing the covers” on page 9 to remove the system unit

covers.

__ 7. Attach the disposable wrist strap to prevent electrostatic discharge from

damaging a device. Attach the adhesive part of the foil to an unpainted

surface on the frame of the unit.

Notes:

a. Follow the same precautions you would use without the wrist strap. The

2209 Disposable Wrist Strap is for static control. It will not increase or

decrease your risk of receiving electric shock when using or working on

electrical equipment.

b. Remove the liner from the copper foil at the end, when you unroll the

strap.

c. Attach the copper foil to an exposed, unpainted metal surface on the

frame of the unit (electrical ground).

Installing the 2746 workstation adapter card

__ 1. DANGER

To prevent a possible electrical shock from touching two surfaces with

different electrical grounds, use one hand, when possible, to connect

or disconnect signal cables. (RSFTD004)

__ 2. If you are using local console on a network (LAN console), remove the

console network cable.

__ 3. If you are using local console directly attached, disconnect the Operations

Console cable connected to the card in one of the following positions:

v270 or 810 system unit, position C07. See “Configuration tables”on

page 15 for more information.

v820 system unit, position C06. See “Configuration tables”on page 15 for

more information.

v825 system unit, position C07. See “Configuration tables”on page 15 for

more information.

v830, 840, SB2, SB3 system unit, position C02. See “Configuration tables”

on page 15 for more information.

v870 or 890 system unit, position C02. See “Configuration tables”on

page 15 for more information.

__ 4. Is there a 2746 card installed in one of the following positions?

v270 or 810 system unit: C06

v820 system unit: C04 or C11

2Upgrading the System Unit from Operations Console to Twinaxial Console (5540) V5R2

v825 system unit: C07

v830, 840, SB2, SB3 system unit: C04, C06, C07, C09, or C10

v870 or 890 system unit: C04, C06, C07, C08, or C09

__ No: Continue with the next step.

__ Yes:Goto“Connecting the Twinaxial cable attachment and Twinaxial

console cable”on page 5.

__ 5. Before you remove the card from the system unit, you need to see if you

have an open position to install the card you removed in a different

position.

Look at the PCI card area. Are there any open positions?

__ Yes: Go to the Install PCI Card topic in the Information Center for

instructions on Moving a card in your iSeries.

__ No: Use the following to help determine card placement.

–Go to the Install PCI Card topic in the Information Center

–Contact your authorized service provider or your authorized

dealer

__ 6. Attention: Adapter cards are fragile. Use static strap when handling,

handle only by the edges, and keep fingers off printed circuit area.

__ 7. Install the new 2746 adapter card in one of the following positions:

v270 system unit: C06

v810 system unit: C07

v820 system unit: C04 or C11

v825 system unit: C06

v830, 840, SB2, SB3 system unit: C04, C06, C07, C09, or C10

v870 or 890 system unit: C04, C06, C07, C08, or C09

__ 8. Does your unit have screws to secure the cards?

__ No: Continue with the next step.

__ Yes: Remove the screw from the card position where you plan to

install the card.

Upgrade Operations Console to twinaxial console 3

__ Go to step 11 on page 5.

__ 9. Your unit has card latches to secure the cards.

__ 10. Open the latch at the card position where you plan to install the card.

Move the latch counterclockwise and then swing the black latch out.

Figure 1. Example of 270, 810, 820, 825, 5075 Card Latch

4Upgrading the System Unit from Operations Console to Twinaxial Console (5540) V5R2

__ 11. Remove the card filler plate.

__ 12. Attention: Adapter cards are fragile:

vHandle only by the edges

vKeep fingers off printed circuit area

vUse static strap when handling

vLeave in protective packaging until ready to install

__ 13. Align the new adapter card with the card holders inside the system unit

and push until it is connected securely.

__ 14. Swing the black latch in and move the other latch clockwise, or install the

screw to secure the card.

__ 15. Go to “Connecting the Twinaxial cable attachment and Twinaxial console

cable”.

Connecting the Twinaxial cable attachment and Twinaxial console

cable

__ 1. Find the 8-port Twinaxial cable attachment (part number 21F5093) and label

the cable, for example, C06.

__ 2. Connect the 8-port Twinaxial cable attachment to the connector on the 2746

card.

Note: Each port on the 8-port attachment cable supports seven devices that

allow for 56 attached devices, of which only 40 can be active.

Figure 2. Example of 830, 840, 870, 890, SB2, SB3, 5079 Card Latches

Upgrade Operations Console to twinaxial console 5

__ 3. Set up the workstation or personal computer (PC) that will be connected to

the system unit and used as the console.

Notes:

a. Place the workstation or PC that will be used as the system unit console

not more than 6 meters (20 feet) from the system unit.

b. Follow the instructions that came with the workstation or PC to set it up.

__ 4. Find a Twinaxial cable and label it console cable.

__ 5. Align the key B in port 0 on the 8-port Twinaxial cable connector with the

slot A on the Twinaxial cable ( Figure 3) attachment.

Push in, hold, and turn the outer ring until it is tight.

__ 6. Connect the other end of the Twinaxial console cable to the PC or

workstation that is the system unit console.

Note: The workstation address of your console must be set to 0. To set the

address, refer to the book that was shipped with your device.

__ 7. Install the side and back covers.

__ 8. DANGER

An electrical outlet that is not correctly wired could place hazardous

voltage on metal parts of the system or the products that attach to the

system. It is the customer’s responsibility to ensure that the outlet is

correctly wired and grounded to prevent an electrical shock.

(RSFTD201)

Plug the following power cords into an electrical outlet.

vSystem unit

Note: Do not power on your system unit at this time.

vSystem unit console

Figure 3. Where to Connect the System Unit Console Cable

6Upgrading the System Unit from Operations Console to Twinaxial Console (5540) V5R2

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere IBM Server Handbücher

IBM

IBM BladeCenter QS20 Bedienungsanleitung

IBM

IBM System x3250 M4 Bedienungsanleitung

IBM

IBM 4252E1U Bedienungsanleitung

IBM

IBM 5100 Produktinformationsblatt

IBM

IBM Power System 8335-GCA Bedienungsanleitung

IBM

IBM x3100 Bedienungsanleitung

IBM

IBM System x3755 M3 7164 Bedienungsanleitung

IBM

IBM POWER 710 Bedienungsanleitung

IBM

IBM System x3690 X5 Bedienungsanleitung

IBM

IBM PureFlex System Bedienungsanleitung

IBM

IBM 87302RU Technisches Handbuch

IBM

IBM System x3200 4362 Bedienungsanleitung

IBM

IBM XSERIES 255 TYPE 8685 Bedienungsanleitung

IBM

IBM 8678 Bedienungsanleitung

IBM

IBM System x3250 Bedienungsanleitung

IBM

IBM xSeries 300 Betriebsanleitung

IBM

IBM NeXtScale System Bedienungsanleitung

IBM

IBM 84894MU Bedienungsanleitung

IBM

IBM System x3300 M4 Bedienungsanleitung

IBM

IBM S822LC Bedienungsanleitung

IBM

IBM 4194D6U Bedienungsanleitung

IBM

IBM System x3500 M2 Type 7839 Bedienungsanleitung

IBM

IBM Power AC922 8335-GTW Bedienungsanleitung

IBM

IBM BladeCenter HS22 Bedienungsanleitung

Beliebte Server Handbücher anderer Marken

HP AlphaServer ES47 Bedienungsanleitung

Dell

Dell PowerEdge R410 Bedienungsanleitung

PowerNAS

PowerNAS CMA Bedienungsanleitung

Supero

Supero FatTwin F617R3-FT Bedienungsanleitung

MSI

MSI P1-109N-L70 Bedienungsanleitung

Dell

Dell PowerEdge XE9640 Handbuch

Dell

Dell PS4100 Montageanleitung

EtroVISION

EtroVISION EV3151 Bedienungsanleitung

NEC

NEC Express5800/T110j Bedienungsanleitung

HP ProLiant Gen9 Bedienungsanleitung

Compaq

Compaq ProLiant 3000 Handbuch

Dell

Dell PowerEdge 3YPMN Bedienungsanleitung

iRobo

iRobo IPC2U Bedienungsanleitung

Nortel

Nortel 1000 Con?guration guide Bedienungsanleitung

Asus

Asus AP7500 Bedienungs- und Wartungshandbuch

Avid Technology

Avid Technology AirSpeed 5000 Bedienungsanleitung

HP Integrity rx2600 Installationsanleitung

Milestone

Milestone Husky IVO 350T Bedienungsanleitung

IBM eServer iSeries 8 Series Bedienungsanleitung

Beliebte Server Handbücher anderer Marken