IBM Eserver pSeries 690 Bedienungsanleitung

pSeries 690 Installation Guide

Installation Guide

SA38-0587-01

ERserver

IBM

pSeries 690 Installation Guide

Installation Guide

SA38-0587-01

ER ser ver

IBM

Second Edition April 2002

Before using this information and the product it supports, read the information in “Safety Notices” on page vii,

Appendix B, “Environmental Notices” on page 47, and Appendix C, “Notices” on page 49.

Note to U.S. Government Users -- Documentation related to restricted rights -- Use, duplication or disclosure is subject

to restrictions set forth is GSA ADP Schedule Contract with IBM Corp.

A reader’s comment form is provided at the back of this publication. If the form has been removed, address comments

to Information Development, Department H6DS-905-6C006, 11400 Burnet Road, Austin, Texas 78758-3493. To send

comments electronically, use this commercial internet address: [email protected]. Any information that you

supply may be used without incurring any obligation to you.

Contents

Safety Notices........................vii

Electrical Safety .......................vii

Laser Safety Information .....................ix

Laser Compliance ......................ix

Data Integrity and Verification ..................xi

About This Book ......................xiii

ISO 9000 .........................xiii

Online Publications ......................xiii

Highlighting .........................xiii

Related Publications ......................xiii

Trademarks .........................xiv

Chapter 1. Getting Started ....................1

Documentation Overview .....................3

Configuring Online Documentation..................5

Viewing the Online Documentation from the Documentation CD .......5

Installing the Online Documentation on a System ............5

Installing the online documentation on a Documentation Server .......5

Chapter 2. Installing the pSeries 690 ................7

Minimum System Configuration...................7

Multiple System Configurations ...................8

Prerequisites to Installing the pSeries 690 ...............8

Weight Reduction ......................8

Step 1. Unpack the pSeries 690 ..................8

Step 2. Check the Inventory ....................9

PrimaryRack Inventory.....................9

Secondary Rack Inventory (If Ordered) ...............9

Step 3. Position and Level the PrimaryRack ..............10

Step 4. Attach and Cable Secondary Rack (If Ordered) ..........11

Connecting Internal Power Cords for the Secondary Rack ........13

Connecting I/O Cables for the Secondary Rack ............14

Connecting the Integrated Battery Feature Power for the Secondary Rack . . . 15

Step 6. Observe this Safety Notice During Installation ...........16

Step 7. Check the Cables and Connect I/O Devices ...........17

Step 8. Verify that the Emergency Power Off (UEPO) Switch is in the

Off

Position 17

Computer Room Emergency Power Off (EPO) ............17

Step 9. Check the Outlets and the Power Source ............19

Step 10. Connect and Route the Power Cords to the pSeries 690 .......21

Step 11. Install the Hardware Management Console (HMC) .........22

Position the HMC and Monitor..................22

Connect the Cables .....................22

Connect the External Modem ..................26

Connect the LAN Cable (If Applicable) ...............27

Plug in the HMC Power Cord ..................27

iii

Step 12. Turn on the IBF Breaker (If Present) .............28

Step 13. Have the Customer Activate the Designated Circuit Breakers .....28

Step 14. Set the Console’s Date and Time ..............28

Step 15. Ensure that the Latest Firmware, HMC Code and Adapter/Drive Microcode

are Installed ........................29

Proceed to Verifying the Hardware Operation..............30

Chapter 3. Verifying the Hardware Operation .............31

Considerations Before Running This Procedure .............31

Loading the Online Diagnostics in Service Mode ............31

Loading the Standalone Diagnostics from CD-ROM............32

Chapter 4. Completing the Installation ...............33

Install the Doors .......................33

Install the Front Door.....................33

Install the Rear Door .....................33

Configure the Network .....................35

Configure Inventory Scout Services .................35

Collect Vital Product Data Information ...............36

Configure the Service Agent ...................37

Running System Verification ...................39

Performing Additional System Verification ...............40

Stopping the Diagnostics ....................40

Service Focal Point ......................40

Getting Started.......................41

Complete System Records and Installation Procedure ...........42

Appendix A. Communications Statements ..............43

Federal Communications Commission (FCC) Statement ..........43

European Union (EU) Statement ..................43

International Electrotechnical Commission (IEC) Statement .........44

United Kingdom Telecommunications Safety Requirements .........44

Avis de conformité aux normes du ministère des Communications du Canada. . . 44

Canadian Department of Communications Compliance Statement .......44

VCCI Statement .......................44

Electromagnetic Interference (EMI) Statement - Taiwan ..........45

Radio Protection for Germany ...................45

Appendix B. Environmental Notices ................47

Product Recycling and Disposal ..................47

Environmental Design .....................47

Acoustical Noise Emissions ...................48

Declared Acoustical Noise Emissions ...............48

Appendix C. Notices .....................49

Appendix D. Securing the Rack .................51

Positioning the Rack ......................51

Installing the Frame Kit .....................51

Rack Tie-Down Kits .....................51

iv pSeries 690 Installation Guide

||||

Mounting Internal Rack Components ...............53

Determine Your Next Step ...................54

Attach the Rack to a Concrete (Non-Raised) Floor ............55

Attaching the Rack to a Short or Long Raised Floor ...........59

Appendix E. Installing Multiple pSeries 690s To One Hardware Management

Console .........................65

Installing the 8-Port ASYNC Adapter.................65

Connect the Serial Cables from the pSeries 690 to the 8-Port ASYNC Adapters 66

Installing the 128-Port ASYNC Adapter ................67

128-Port ASYNC Adapter Line Connectors .............67

Setting a RAN Node Number ..................68

Configuring the 128-Port ASYNC Adapter ..............69

Updating the Device Driver...................71

Connect the Serial Cables from the pSeries 690 to the 128-Port ASYNC Adapters 71

Verify Installation is Complete by Using the HMC Interface .........72

Appendix F. System Records ..................75

Record the Identification Numbers .................75

Record System - CPU, Memory, and I/O Configuration ..........77

Verify that All Hardware is Present .................81

Appendix G. Subsystem Positioning and Cabling ...........83

Operator Panel Cable and Diskette Drive Cable to the Media Subsystem (rear view) 83

I/O Subsystem Positions, Fully Populated Primary and Secondary Rack

(rear view without IBF) ....................84

I/O Subsystem Positions, Fully Populated Primary and Secondary Rack (rear view

with IBFs).........................85

Placement of Subsystem 4 in a Two-Rack Configuration

(rear view with IBF) .....................86

I/O Subsystems (1 Through 4 Without IBFs) RIO Cabling to I/O Books .....87

I/O Subsystems (5 and 6) RIO Cabling to the Secondary I/O Book ......88

I/O Subsystems (7 and 8) RIO Cabling to the Third I/O Book ........89

I/O Subsystem (1 through 3 with IBFs) RIO Cabling to I/O Books .......90

RIO Cable to I/O Subsystem (4 through 6) with IBFs Installed ........91

I/O Subsystems (7 and 8) RIO Cabling to the Third I/O Book ........92

Power and SCSI Cables to the Media Subsystem ............93

Hardware Management Console for pSeries (HMC) to the Primary I/O Book . . . 94

Appendix H. Cabling Information .................95

Power Cabling ........................95

RIO Cables and I/O Power Cables .................97

Appendix I. Service Processor Setup and Test ............101

Service Processor Setup Checklist .................101

Testing the Setup ......................102

Testing Call-In ......................102

Testing Call-Out ......................103

Serial Port Configuration ...................103

Contents v

||||||||||||||||||||

Appendix J. Removing and Installing the Rack Top Frame........105

Options for Performing this Procedure................105

Required Tools .......................106

Removing the Covers .....................107

Side Cover Removal ....................108

Removing the Rack Top Frame for Clearance Through Doorways ......108

Preparing for Rack Top Frame Installation for pSeries 690 (Reduced Height

Option) RPQ8A1173 .....................115

Installing the Rack Top Frame ..................119

Cover Replacement......................126

Index ..........................127

vi pSeries 690 Installation Guide

||||

Safety Notices

Attention: When moving or relocating certain configurations of the system, the Bulk

Power Regulators (BPR’s) must be removed from the top of the rack (front and rear) to

ensure product stability. Specifically, removal of the top two BPR’s in the front and rear

is required in systems that have less then 2 I/O drawers in the rack.

danger

notice indicates the presence of a hazard that has the potential of causing

death or serious personal injury.

Danger

notices appear on the following pages:

vvii

v16

caution

notice indicates the presence of a hazard that has the potential of causing

moderate or minor personal injury.

Caution

notices appear on the following pages:

vviii

vix

v16

v19

v22

For a translation of the safety notices contained in this book, see the

System Unit

Safety Information

, order number SA23-2652.

Electrical Safety

Observe the following safety instructions any time you are connecting or disconnecting

devices attached to the system.

DANGER

An electrical outlet that is not correctly wired could place hazardous voltage

on metal parts of the system or the devices that attach to the system. It is the

responsibility of the customer to ensure that the outlet is correctly wired and

grounded to prevent an electrical shock.

Use one hand, when possible, to connect or disconnect signal cables to

prevent a possible shock from touching two surfaces with different electrical

potentials.

During an electrical storm, do not connect cables for display stations, printers,

telephones, or station protectors for communications lines.

vii

CAUTION:

This product is equipped with a four-wire (three-phase and ground) power cable

for the user’s safety. Use this power cable with a properly grounded electrical

outlet to avoid electrical shock.

DANGER

To prevent electrical shock hazard, disconnect all power cables from the

electrical outlet before relocating the system.

CAUTION:

This unit has more than one power supply cord. Follow procedures for removal

of power from the system when directed.

CAUTION:

Energy hazard, remove power before servicing.

CAUTION:

Energy hazard, remove all jewelry before servicing.

viii pSeries 690 Installation Guide

Andere Handbücher für eserver pSeries 690

Inhaltsverzeichnis

Andere IBM Server Handbücher

IBM

IBM 8038 Bedienungsanleitung

IBM

IBM 884872U - eServer 326 - 8848 Bedienungsanleitung

IBM

IBM System x3610 Bedienungsanleitung

IBM

IBM Netfinity 6000R Bedienungsanleitung

IBM

IBM 79463AU Bedienungsanleitung

IBM

IBM pSeries 650 Bedienungsanleitung

IBM

IBM x3550 M4 Type 7914 Montage- und Wartungsanleitung

IBM

IBM eserver pSeries 690 Bedienungsanleitung

IBM

IBM 9040-MR9 Bedienungsanleitung

IBM

IBM totalstorage 326 Bedienungsanleitung

IBM

IBM xSeries 330 Betriebsanleitung

IBM

IBM 425162U Bedienungsanleitung

IBM

IBM X366 Series Bedienungsanleitung

IBM

IBM B50 Bedienungsanleitung

IBM

IBM 847620U - Netfinity 3000 - 20U Betriebsanleitung

IBM

IBM xSeries 230 6RY Betriebsanleitung

IBM

IBM BladeCenter HS20 7981 Bedienungsanleitung

IBM

IBM System x3650 M4 Type 7915 Bedienungsanleitung

IBM

IBM eserver i5 Bedienungsanleitung

IBM

IBM System x3250 M4 Bedienungsanleitung

IBM

IBM 8686 - Eserver xSeries 360 Betriebsanleitung

IBM

IBM eServer xSeries 225 Type 8647 Bedienungsanleitung

IBM

IBM 4348 Bedienungsanleitung

IBM

IBM Power System 9009-42A Bedienungsanleitung

Beliebte Server Handbücher anderer Marken

HP AlphaServer ES47 Bedienungsanleitung

Dell

Dell PowerEdge R410 Bedienungsanleitung

PowerNAS

PowerNAS CMA Bedienungsanleitung

Supero

Supero FatTwin F617R3-FT Bedienungsanleitung

MSI

MSI P1-109N-L70 Bedienungsanleitung

Dell

Dell PowerEdge XE9640 Handbuch

Dell

Dell PS4100 Montageanleitung

EtroVISION

EtroVISION EV3151 Bedienungsanleitung

NEC

NEC Express5800/T110j Bedienungsanleitung

HP ProLiant Gen9 Bedienungsanleitung

Compaq

Compaq ProLiant 3000 Handbuch

Dell

Dell PowerEdge 3YPMN Bedienungsanleitung

iRobo

iRobo IPC2U Bedienungsanleitung

Nortel

Nortel 1000 Con?guration guide Bedienungsanleitung

Asus

Asus AP7500 Bedienungs- und Wartungshandbuch

Avid Technology

Avid Technology AirSpeed 5000 Bedienungsanleitung

HP Integrity rx2600 Installationsanleitung

Milestone

Milestone Husky IVO 350T Bedienungsanleitung