IBM 220 Bedienungsanleitung

7206 Model 220 External 4mm Tape Drive

7206 Model 220

4mm Tape Drive

Service Guide

SY32-0409-01



7206 Model 220 External 4mm Tape Drive

7206 Model 220

4mm Tape Drive

Service Guide

SY32-0409-01



Note!

Before using this information and the product it supports, be sure to read the general information under “Notices” on

page v.

First Edition (February, 2000)

This edition, SY32–0409–01, applies to Model 220 of the 7206 4mm Tape Drive and to all subsequent releases and

modifications until otherwise indicated in new editions. This edition applies only to the specified model of the

device.

US Government Users Restricted Rights – Use, duplication or disclosure restricted by GSA ADP Schedule Contract

with IBM Corp.

Contents

Notices ...............v

Safety and Environmental Notices .......vi

Danger Notices ............vi

Caution Notices ............vii

Attention Notices ...........vii

Product Recycling and Disposal ......vii

Battery Return Program .........viii

Environmental Design .........viii

Electronic Emission Notices.........viii

Federal Communications Commission (FCC)

Statement..............viii

Trademarks...............x

About This Guide ..........xi

Related Publications ...........xi

How to send your comments ........xii

Chapter 1. Reference Information....1

FrontView...............2

Operator Controls ...........2

Emergency Eject Feature .........3

Indicator Lights ............3

Rear View ...............6

Internal View ..............7

Rear View of the Drive ...........8

System Requirement............9

Specifications ..............9

Cleaning the Tape Drive ..........10

Chapter 2. Using the Media ......13

Types of Tape Cartridges ..........13

Recommendations for Data Cartridge Usage . . . 14

Data Cartridge Erasure ..........14

Storage and Shipping Environments ......14

Tape Cartridge Storage .........15

Operating in Harsh Environments .......16

Setting the Write-Protect Switch .......16

Chapter 3. Maintenance Analysis

Procedures.............17

Purpose of the MAPs ...........17

Flowchart of the MAPs ..........18

Step 1: Power and Fan...........19

Step 2: Electrical Outlet Voltage........19

Step 3: Power Cable ...........20

Step 4: Power Supply, Fan, and Tape Drive ....20

Step 5: Cooling Fan............21

Step 6: Tape Drive ............21

Step 7: SCSI Address Switch.........22

Step 8: SCSI Address Cable .........22

Step 9: Tape Drive Status Lights .......22

Step 10: Power Supply Voltage Level ......23

Step 11: Reassembly ...........24

Step 12: External SCSI Cable Connection ....24

Step 13: Terminator Connection........25

Step 14: Configuration...........25

Step 15: AIX Diagnostics ..........26

Chapter 4. Removal and Replacement

Procedures.............27

Handling Static-Sensitive Devices .......27

Removing and Replacing the Cover ......28

Removing and Replacing the Drive ......30

Removing and Replacing the Power Supply . . . 32

Removing and Replacing the Cooling Fan ....34

Manually Removing a Tape Cartridge .....35

Chapter 5. Parts Diagram and Parts

List ................37

How To Use This Parts List .........37

Example of Parts Listing .........37

Assembly 1: Parts Diagram .........38

Appendix A. Power Cables ......41

Appendix B. Ordering Tape Cartridges 45

Appendix C. Safety Inspection

Procedures.............47

Readers’ Comments — We’d Like to

Hear from You ...........51

iv 7206 Model 220 Service Guide

Notices

This information was developed for products and services offered in the U.S.A.

IBM may not offer the products, services, or features discussed in this document in

other countries. Consult your local IBM representative for information on the

products and services currently available in your area. Any reference to an IBM

product, program, or service is not intended to state or imply that only that IBM

product, program, or service may be used. Any functionally equivalent product,

program, or service that does not infringe any IBM intellectual property right may

be used instead. However, it is the user’s responsibility to evaluate and verify the

operation of any non-IBM product, program, or service.

IBM may have patents or pending patent applications covering subject matter

described in this document. The furnishing of this document does not give you

any license to these patents. You can send license inquiries, in writing, to:

IBM Director of Licensing

IBM Corporation

500 Columbus Avenue

Thornwood, NY 10594

U.S.A.

For license inquiries regarding double-byte (DBCS) information, contact the IBM

Intellectual Property Department in your country or send inquiries, in writing, to:

IBM World Trade Asia Corporation

Licensing

2-31 Roppongi 3-chome, Minato-ku

Tokyo 106, Japan

The following paragraph does not apply to the United Kingdom or any other

country where such provisions are inconsistent with local law:

INTERNATIONAL BUSINESS MACHINES CORPORATION PROVIDES THIS

PUBLICATION “AS IS”WITHOUT WARRANTY OF ANY KIND, EITHER

EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED

WARRANTIES OF NON-INFRINGEMENT, MERCHANTABILITY OR FITNESS

FOR A PARTICULAR PURPOSE. Some states do not allow disclaimer of express or

implied warranties in certain transactions, therefore, this statement may not apply

to you.

This information could include technical inaccuracies or typographical errors.

Changes are periodically made to the information herein; these changes will be

incorporated in new editions of the publication. IBM may make improvements

and/or changes in the product(s) and/or the program(s) described in this

publication at any time without notice.

Any references in this information to non-IBM Web sites are provided for

convenience only and do not in any manner serve as an endorsement of those Web

sites. The materials at those Web sites are not part of the materials for this IBM

product and use of those Web sites is at your own risk.

Any performance data contained herein was determined in a controlled

environment. Therefore, the results obtained in other operating environments may

vary significantly. Some measurements may have been made on development-level

systems and there is no guarantee that these measurements will be the same on

generally available systems. Furthermore, some measurement may have been

estimated through extrapolation. Actual results may vary. Users of this document

should verify the applicable data for their specific environment.

Information concerning non-IBM products was obtained from the suppliers of

those products, their published announcements or other publicly available sources.

IBM has not tested those products and cannot confirm the accuracy of

performance, compatibility or any other claims related to non-IBM products.

Questions on the capabilities of non-IBM products should be addressed to the

suppliers of those products.

All statements regarding IBM’s future direction or intent are subject to change or

withdrawal without notice, and represent goals and objectives only.

If you are viewing this information softcopy, the photographs and color

illustrations may not appear.

The drawings and specifications contained herein shall not be reproduced in whole

or in part without the written permission of IBM.

IBM has prepared this publication for use by hardware service representatives in

the maintenance or repair of the specific machines indicated. IBM makes no

representations that it is suitable for any other purpose.

Safety and Environmental Notices

Danger Notices

A danger notice calls attention to a situation that is potentially lethal or extremely

hazardous to people.

Use the following danger notices throughout this book.

DANGER

To prevent a possible electrical shock from touching two surfaces with

different electrical grounds, use one hand, when possible, to connect or

disconnect signal cables. (RSFTD004)

DANGER

Dangerous voltage being measured. (RSFTD005)

vi 7206 Model 220 Service Guide

DANGER

Up to 240 V ac is present at the power module connectors when the main

power cord is connected to a power source. (RSFTD010)

DANGER

An electrical outlet that is not correctly wired could place hazardous voltage

on metal parts of the system or the products that attach to the system. It is the

customer’s responsibility to ensure that the outlet is correctly wired and

grounded to prevent an electrical shock. (RSFTD201)

DANGER

To prevent a possible electrical shock when adding or removing any devices

to or from the system, ensure that the power cords for those devices are

unplugged before the signal cables are connected or disconnected. If possible,

disconnect all power cords from the existing system before you add or

remove a device. (RSFTD203)

DANGER

To prevent a possible electrical shock when installing the device, ensure that

the power cord for that device is unplugged before installing signal cables.

(RSFTD204)

DANGER

Do not attempt to open the covers of the power supply. Power supplies are

not serviceable and are to be replaced as a unit. (RSFTD217)

Caution Notices

A caution notice calls attention to a situation that is potentially hazardous to

people because of some existing condition.

Use the following caution notices throughout this book.

Attention Notices

An attention notice indicates the possibility of damage to a program, device,

system, or data.

Product Recycling and Disposal

Components of the system, such as structural parts and circuit cards, can be

recycled where recycling facilities exist. IBM does not currently collect and recycle

used IBM products from customers in the United States other than those products

that are involved in trade-in programs. Companies are available to disassemble,

reutilize, recycle, or dispose of electronic products. Contact an IBM account

representative for more information.

The system unit contains batteries and circuit boards with lead solder. Before you

dispose of this unit, these batteries and circuit boards must be removed and

discarded according to local regulations or recycled where facilities exist. This book

contains specific information on each battery type where applicable.

Notices vii

Battery Return Program

In the United States, IBM has established a collection process for reuse, recycling,

or proper disposal of used IBM batteries and battery packs. For information on

proper disposal of the batteries in this unit, please contact IBM at 1-800-426-4333.

Please have the IBM part number that is listed on the battery available when you

make your call. For information on battery disposal outside the United States,

contact your local waste disposal facility.

Environmental Design

The environmental efforts that have gone into the design of the system signify

IBM’s commitment to improve the quality of its products and processes. Some of

these accomplishments include the elimination of the use of Class I

ozone-depleting chemicals in the manufacturing process, reductions in

manufacturing wastes, and increased product energy efficiency. For more

information, contact an IBM account representative.

Electronic Emission Notices

The following Statement applies to this IBM product. The statement for other IBM

products intended for use with this product will appear in their accompanying

manuals.

Federal Communications Commission (FCC) Statement

Note: This equipment has been tested and found to comply with the limits for a

class B digital devices, pursuant to Part 15 of the FCC Rules. These limits are

designed to provide reasonable protection against harmful interference in a

residential installation. This equipment generates, uses, and can radiate radio

frequency energy and, if not installed and used in accordance with the instructions,

may cause harmful interference to radio communications. However, there is no

guarantee that interference will not occur in a particular installation. If this

equipment does cause harmful interference to radio or television reception, which

can be determined by turning the equipment off and on, the user is encouraged to

try to correct the interference by one or more of the following measures:

vReorient or relocate the receiving antenna.

vIncrease the separation between the equipment and receiver.

vConnect the equipment into an outlet on a circuit different from that to which

the receiver is connected.

vConsult an IBM authorized dealer or service representative for help.

Properly shielded and grounded cables and connectors must be used in order to

meet FCC emission limits. Proper cables and connectors are available from IBM

authorized dealers. IBM is not responsible for any radio or television interference

caused by using other than recommended cables or connectors or by unauthorized

changes or modifications to this equipment. Unauthorized changes or

modifications could void the user’s authority to operate the equipment.

This device complies with Part 15 of the FCC Rules. Operation is subject to the

following two conditions: (1) this device may not cause harmful interferences, and

(2) this device must accept any interferences received, including interference that

may cause undesired operation.

Responsible Party:

viii 7206 Model 220 Service Guide

Andere Handbücher für 220

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere IBM Lagerung Handbücher

IBM

IBM DS3500 Betriebsanleitung

IBM

IBM SAN Volume Controller 2145-CG8 Betriebsanleitung

IBM

IBM N Series Montageanleitung

IBM

IBM TS7700 Series Installationsanleitung

IBM

IBM Ultrastar 18ZX Bedienungsanleitung

IBM

IBM Storwize V7000 Bedienungsanleitung

IBM

IBM Modbus Plus Bedienungsanleitung

IBM

IBM Ultrastar 36LZX Bedienungsanleitung

IBM

IBM System Storage TS3500 Bedienungsanleitung

IBM

IBM DDS Generation 6 USB Bedienungsanleitung

IBM

IBM Ultrastar 9LZX Bedienungsanleitung

IBM

IBM TotalStorage DS8000 Bedienungsanleitung

IBM

IBM Storwize V5000 Bedienungsanleitung

IBM

IBM Ultrastar 36Z15 Bedienungsanleitung

IBM

IBM FlashSystem 840 Bedienungsanleitung

IBM

IBM Storwize V7000 Bedienungsanleitung

IBM

IBM TU3 2104 Handbuch

IBM

IBM 01K1316 Betriebsanleitung

IBM

IBM FC 5026 Bedienungsanleitung

IBM

IBM DYLA-28100 - Travelstar 8.1 GB Hard Drive Bedienungsanleitung

IBM

IBM 1 GB Microdrive Storage Card Bedienungsanleitung

IBM

IBM N6270 Bedienungsanleitung

IBM

IBM TotalStorage SAN256N Director 2045-N16 Produkthandbuch

IBM

IBM Ultrastar 73LZX Bedienungsanleitung

Beliebte Lagerung Handbücher anderer Marken

QNAP

QNAP TS 32PXU Series Bedienungsanleitung

LaCie

LaCie RUGGED RAID Bedienungsanleitung

Freecom

Freecom CLS DOCK Bedienungsanleitung

PNY

PNY Attache P-FD64MBATT3 Bedienungsanleitung

HP StorageWorks MSL2024 Bedienungsanleitung

OLT

OLT 6x6 Maximizer Bedienungsanleitung

Transcend

Transcend JetFlash 160 Bedienungsanleitung

LaCie

LaCie RUGGED MINI Bedienungsanleitung

Thunderbolt

Thunderbolt 600 Bedienungsanleitung

Panasonic

Panasonic LB-DH8 series Handbuch

Intel

Intel RAID High Availability Bedienungsanleitung

LaCie

LaCie 12big Thunderbolt 3 Bedienungsanleitung

Spectra Logic

Spectra Logic T-Series Spectra T50e Bedienungsanleitung

Panasonic

Panasonic LKM-F931-1 Bedienungsanleitung

Tabernus

Tabernus Enterprise Erase E2400 Bedienungsanleitung

Rocstor

Rocstor COMMANDER 3F series Bedienungsanleitung

HP P9000 Bedienungsanleitung

Western Digital

Western Digital Ultrastar Data60 Bedienungsanleitung