IBM 3409-S03 Bedienungsanleitung

IBM Cloud Object Storage System™

Version 3.13.4

Slicestor®2584 Appliance Manual

3409-S03/3401-S03/3403-S03

IBM

Note

Before using this information and the product it supports, read the following information:

vThe general information in Notices

vThe information in Safety and environmental notices

vThe information in the IBM Environmental Notices and User Guide (provided on a DVD)

This edition applies to IBM Cloud Object Storage System™Slicestor®2584 and is valid until replaced by new

editions.

US Government Users Restricted Rights – Use, duplication or disclosure restricted by GSA ADP Schedule Contract

with IBM Corp.

Contents

Figures ............... v

Tables ............... vii

Safety and environmental notices ... ix

Safety notices .............. ix

Environmental notices........... xii

Declared noise emissions ........ xiii

Support information ......... xv

Chapter 1. Appliance safety precautions 1

Introduction .............. 1

Damage ................ 1

Handling ............... 1

Operation ............... 3

Electrical safety ............. 5

Rack system safety precautions ........ 6

Electrostatic discharge (ESD) precautions ..... 7

Regional safety ............. 7

Chapter 2. System overview ...... 9

Chassis ................ 9

The enclosure core product ......... 9

Components .............. 10

Power supply unit (2200 kW PSU)....... 14

Power supply unit (2800 kW PSU)....... 15

Cooling module ............. 16

Compute modules ............ 18

Chapter 3. Installation ........ 21

Preparation .............. 21

Installation .............. 22

Power cord connection .......... 24

Grounding checks ............ 24

Data security .............. 25

Chapter 4. Operation......... 27

Before you begin ............ 27

Power on ............... 27

Ops panel LEDs ............. 28

Unit identification number ......... 29

Power down .............. 30

Lock the drawers ............ 30

Chapter 5. Troubleshooting ...... 31

Initial start-up problems .......... 31

LEDs ............... 31

Thermal sensors ............. 37

Troubleshooting ............. 37

Hardware faults ............. 39

Chapter 6. Module replacement .... 41

Overview ............... 41

General procedures ............ 41

Replace a disk drive in carrier (DDIC) ..... 43

Replace a cooling module ......... 45

Replace a power supply unit (PSU) ...... 46

Replace a compute module ......... 47

Battery removal ............. 50

Appendix A. Technical specifications 51

Dimensions .............. 51

Components (fully populated) ........ 51

Thermal ............... 51

Temperature and humidity ......... 51

Cooling modules ............ 52

AP-TL-1 and AP-LS-1 compute modules..... 52

Power supply unit (2200 kW PSU)....... 53

Power supply unit (2800 kW PSU)....... 53

Supported drives ............ 54

Shock and vibration tolerance ........ 54

Appendix B. Standards and regulations 55

EMC qualification ............ 55

Acoustics ............... 56

AC power cords ............. 56

SMM Phase .............. 56

Appendix C. Post Codes ....... 57

SEC Phase............... 57

DXE Phase .............. 57

BDS Phase............... 58

SMM Phase .............. 59

Notices .............. 61

Trademarks .............. 63

Homologation statement .......... 63

iv Slicestor®2584 Appliance Manual

Figures

1. Lifting hazard ............ 2

2. Chassis label (FCC compliance) ...... 3

3. Module bay caution label ........ 4

4. Hot surface warning label ........ 4

5. PSU warning label .......... 5

6. Drawer caution label .......... 5

7. Enclosure front view .......... 9

8. AP-TL-1 module locations........ 10

9. AP-LS-1 module locations........ 10

10. Drawer LEDs (left side only) ....... 12

11. A disk drive in carrier (DDIC) ...... 12

12. Enclosure operator’s panel ....... 14

13. 2200 W PSU ............ 15

14. PSU LEDs ............. 15

15. 2800 W PSU ............ 16

16. PSU LEDs ............. 16

17. Cooling module ........... 17

18. Cooling module LEDs ......... 18

19. AP-TL-1 module ........... 18

20. AP-LS-1 module ........... 19

21. Unpacking the system ......... 22

22. Mounting the system into a rack (left rail only) 23

23. Rear enclosure mounting ........ 24

24. PSU Power Switch and LEDs ...... 27

25. Ops panel LEDs ........... 28

26. Anti-tamper locks .......... 30

27. PSU LEDs ............. 31

28. Cooling module LEDs ......... 32

29. Operator’s panel LEDs......... 33

30. Drawer LEDs (left sideplane only) ..... 35

31. Drive Fault LED ........... 36

32. Compute module LEDs ........ 36

33. Anti-tamper locks (shown disengaged) 42

34. Opening the bottom drawer ....... 42

35. Drawer latch ............ 43

36. Drive location plan .......... 43

37. Removing a DDIC .......... 44

38. Installing a DDIC .......... 44

39. Latch position of a correctly inserted drive 45

40. Cooling module LEDs ......... 45

41. Removing a Cooling Module (1) ..... 46

42. Removing a Cooling Module (2) ..... 46

43. Removing a PSU module (1) ....... 47

44. Removing a PSU Module (2) ....... 47

45. AP-TL-1 compute module LEDs ..... 48

46. AP-LS-1 module ........... 48

47. Removing a module (1). ........ 49

48. Removing a module (2). ........ 49

49. Remove the battery .......... 50

vi Slicestor®2584 Appliance Manual

Tables

1. Declared noise emissions in accordance with

ISO 9296(1,2,3) ............ xiii

2. Cooling module LED states ....... 18

3. Ops panel LED states ......... 28

4. PSU LED states ........... 31

5. Cooling module LED descriptions ..... 32

6. Ops panel LED descriptions ....... 33

7. Ops panel LED states ......... 33

8. Drawer LED descriptions ........ 35

9. Compute module LED descriptions .... 37

10. Alarm Conditions .......... 37

11. Enclosure dimensions ......... 51

12. Components ............ 51

13. Thermal specifications ......... 51

14. Temperature and humidity limits ..... 51

15. Compute canister specifications ...... 52

16. PSU specifications .......... 53

17. PSU specifications .......... 53

18. Supported disk drives ......... 54

19. Shock and vibration tolerance ...... 54

20. Power cord specifications ........ 56

21. POST Codes – SMM Phase ....... 56

22. POST Codes – SEC Phase ........ 57

23. POST Codes – BDS Phase ........ 57

24. POST Codes – BDS Phase ........ 58

25. POST Codes – SMM Phase ....... 59

viii Slicestor®2584 Appliance Manual

Safety and environmental notices

Review the safety notices, environmental notices, and electronic emission notices for IBM®Cloud Object

Storage System before you install and use the product.

Suitability for telecommunication environment - This product is not intended to connect directly or

indirectly by any means whatsoever to interfaces of public telecommunications networks.

Examples of a caution and a danger notice. Numbers in parentheses refer to message numbers in the IBM

Safety Notices publication G229-9054, which is included with your product.

CAUTION:

A caution notice indicates the presence of a hazard that has the potential of causing moderate or

minor personal injury. (C001)

DANGER

A danger notice indicates the presence of a hazard that has the potential of causing death or serious

personal injury. (D002)

Safety notices

Safety notices for this product.

Familiarize yourself with the IBM Safety Notices publication G229-9054, which is included with your

product.

DANGER: When working on or around the system, observe the following precautions:

Electrical voltage and current from power, telephone, and communication cables are hazardous. To

avoid a shock hazard:

• , connect power to this unit only with the IBM provided powerIf IBM supplied a power cord(s)

cord. Do not use the IBM provided power cord for any other product.

• Do not open or service any power supply assembly.

• Do not connect or disconnect any cables or perform installation, maintenance, or reconfiguration

of this product during an electrical storm.

• The product might be equipped with multiple power cords. To remove all hazardous voltages,

disconnect all power cords.

• Connect all power cords to a properly wired and grounded electrical outlet. Ensure that the outlet

supplies proper voltage and phase rotation according to the system rating plate.

• Connect any equipment that will be attached to this product to properly wired outlets.

• When possible, use one hand only to connect or disconnect signal cables.

• Never turn on any equipment when there is evidence of fire, water, or structural damage.

• Do not attempt to switch on power to the machine until all possible unsafe conditions are corrected.

• Assume that an electrical safety hazard is present. Perform all continuity, grounding, and power

checks specified during the subsystem installation procedures to ensure that the machine meets

safety requirements.

• Do not continue with the inspection if any unsafe conditions are present.

• Disconnect the attached power cords, telecommunications systems, networks, and modems before

you open the device covers, unless instructed otherwise in the installation and configuration

procedures.

• Connect and disconnect cables as described in the following procedures when installing, moving,

or opening covers on this product or attached devices.

To disconnect:

1. Turn off everything (unless instructed otherwise).

2. Remove the power cords from the outlets.

3. Remove the signal cables from the connectors.

4. Remove all cables from the devices.

To connect:

1. Turn off everything (unless instructed otherwise).

2. Attach all cables to the devices.

3. Attach the signal cables to the connectors.

4. Attach the power cords to the outlets.

5. Turn on the devices.

• Sharp edges, corners and joints may be present in and around the system. Use care when handling

equipment to avoid cuts, scrapes and pinching. (D005)

DANGER: Heavy equipment — personal injury or equipment damage might result if mishandled.

(D006)

xSlicestor®2584 Appliance Manual

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere IBM Lagerung Handbücher

IBM

IBM 4146 T30 Bedienungsanleitung

IBM

IBM SAN384B-2 Handbuch

IBM

IBM FlashSystem 710 Bedienungsanleitung

IBM

IBM BladeCenter Management Module Bedienungsanleitung

IBM

IBM 3420 Bedienungsanleitung

IBM

IBM DS4700 EXPRESS Installationsanleitung

IBM

IBM ATA-3 Bedienungsanleitung

IBM

IBM DS8000 - ADDITIONAL INFORMATION Bedienungsanleitung

IBM

IBM DTCA-23240 - Travelstar 3.2 GB Hard Drive Bedienungsanleitung

IBM

IBM 7133 Series Bedienungsanleitung

IBM

IBM DBCA-206480 - Travelstar 6.4 GB Hard Drive Bedienungsanleitung

IBM

IBM TU3 2104 Handbuch

IBM

IBM Deskstar 14GXP Bedienungsanleitung

IBM

IBM ATA-100 Bedienungsanleitung

IBM

IBM SAN Volume Controller 2145-CG8 Betriebsanleitung

IBM

IBM T400 Bedienungsanleitung

IBM

IBM System Storage TS2240 Bedienungsanleitung

IBM

IBM DTCA-23240 - Travelstar 3.2 GB Hard Drive Bedienungsanleitung

IBM

IBM DDS Generation 6 Bedienungsanleitung

IBM

IBM Universal Tape Library Bedienungsanleitung

IBM

IBM System Storage DS5020 Betriebsanleitung

IBM

IBM Storwize V7000 Bedienungsanleitung

IBM

IBM Ultrastar 18ZX Bedienungsanleitung

IBM

IBM Travelstar 6GT Bedienungsanleitung

Beliebte Lagerung Handbücher anderer Marken

QNAP

QNAP TS 32PXU Series Bedienungsanleitung

LaCie

LaCie RUGGED RAID Bedienungsanleitung

Freecom

Freecom CLS DOCK Bedienungsanleitung

PNY

PNY Attache P-FD64MBATT3 Bedienungsanleitung

HP StorageWorks MSL2024 Bedienungsanleitung

OLT

OLT 6x6 Maximizer Bedienungsanleitung

Transcend

Transcend JetFlash 160 Bedienungsanleitung

LaCie

LaCie RUGGED MINI Bedienungsanleitung

Thunderbolt

Thunderbolt 600 Bedienungsanleitung

Panasonic

Panasonic LB-DH8 series Handbuch

Intel

Intel RAID High Availability Bedienungsanleitung

LaCie

LaCie 12big Thunderbolt 3 Bedienungsanleitung

Spectra Logic

Spectra Logic T-Series Spectra T50e Bedienungsanleitung

Panasonic

Panasonic LKM-F931-1 Bedienungsanleitung

Tabernus

Tabernus Enterprise Erase E2400 Bedienungsanleitung

Rocstor

Rocstor COMMANDER 3F series Bedienungsanleitung

HP P9000 Bedienungsanleitung

Western Digital

Western Digital Ultrastar Data60 Bedienungsanleitung