IBM T400 Bedienungsanleitung

IBMTotalStorageLTOUltrium2TapeDrive

Models T400 and T400F

Setup, Operator, and Service Guide

GA32-0455-00



IBMTotalStorageLTOUltrium2TapeDrive

Models T400 and T400F

Setup, Operator, and Service Guide

GA32-0455-00



Note

Before using this guide and the product it supports, read the information in “Safety and Environmental Notices” on page vii

and “Notices” on page 101.

First Edition (November 2002)

This edition applies to the IBM TotalStorage LTO Ultrium 2 Tape Drive Models T400 and T400F Setup, Operator, and

Service Guide and to all subsequent releases and modifications until otherwise indicated in new editions.

US Government Users Restricted Rights – Use, duplication or disclosure restricted by GSA ADP Schedule Contract

with IBM Corp.

Contents

Safety and Environmental Notices .................vii

Danger Notice .........................vii

Caution Notice .........................vii

Attention Notice ........................viii

Laser Safety and Compliance ...................viii

Preface ............................ix

Intended Audience ........................ix

Related Publications .......................ix

IBM Ultrium Publications.....................ix

IBM Fibre Channel Publications ..................ix

Other Publications .......................ix

Chapter 1. Introduction ......................1

Cartridge Compatibility ......................2

Speed Matching and Channel Calibration ...............2

Sleep Mode ..........................2

Supported Servers and Operating Systems ...............3

SCSI Attachment ........................4

Physical Characteristics of the SCSI Interface .............4

Speed ...........................4

Address Assignments ......................5

Installing, Removing, or Resetting a Drive on an Active SCSI Bus .....5

Fibre Channel Attachment .....................6

Supported Topologies ......................6

Speed ...........................7

Address Assignments ......................7

World Wide Names.......................8

Physical Characteristics of the Fibre Channel Interface .........8

Installing, Removing, or Resetting a Drive on an Active Fibre Channel ....8

Supported Device Drivers .....................9

Chapter 2. Specifications ....................11

Chapter 3. Installing the Tape Drive ................13

Rear View of the SCSI Drive ....................14

Rear View of the Fibre Channel Drive ................15

Step 1. Unpack the Drive .....................16

Step 2. Remove Power from the Enclosure ..............16

Step 3. Set the SCSI ID or Arbitrated Loop Physical Address ........17

Setting the SCSI ID (SCSI Drive Only) ...............17

Setting the Arbitrated Loop Physical Address (Fibre Channel Drive Only) 19

Step 4. Change the Link Services of the Drive (optional) .........24

Step 5. Mount the Tape Drive into the Enclosure ............26

Step 6. Connect and Test Power to the Tape Drive............27

Step 7. Connect the Internal SCSI or Fibre Channel Cable.........27

Step 8. Connect the Internal LDI Cable (optional) ............28

Step 9. Run Drive Diagnostics ...................28

Step 10. Install the Device Drivers..................28

Step 11. Connect the External SCSI or Fibre Channel Interface to the Server 28

Connect the External SCSI Interface to the Server ...........28

Connect the External Fibre Channel Interface to the Server .......29

Step 12. Connect the External LDI Interface to the Server (optional) .....29

Step 13. Configure the Tape Drive to the Server, Switch, or Hub.......29

Chapter 4. Operating the Tape Drive ................31

Status Light ..........................32

Unload Button .........................33

Single-Character Display .....................33

Single Red Dot ........................33

Inserting a Tape Cartridge .....................34

Removing a Tape Cartridge ....................35

Cleaning the Drive Head .....................35

Selecting a Diagnostic or Maintenance Function.............36

Exiting Maintenance Mode ....................45

Updating the Firmware ......................45

Updating Firmware through the SCSI or Fibre Channel Interface .....45

Updating Firmware through the Library/Drive Interface .........45

Updating the Firmware with an FMR Tape Cartridge ..........46

Chapter 5. Using the Media....................47

Data Cartridge .........................48

Cleaning Cartridges .......................49

Setting the Write-Protect Switch ..................50

Handling the Cartridges......................50

Provide Training .......................51

Ensure Proper Packaging ....................51

Provide Proper Acclimation and Environmental Conditions ........52

Perform a Thorough Inspection ..................52

Handle the Cartridge Carefully ..................53

Examples of Cartridge Problems .................54

Repositioning or Reattaching a Leader Pin...............55

Repositioning a Leader Pin ...................55

Reattaching a Leader Pin ....................57

Environmental and Shipping Specifications for Tape Cartridges .......62

Disposing of Tape Cartridges....................63

Ordering Media Supplies .....................63

Ordering Custom Bar Code Labels ................64

Chapter 6. Resolving Problems ..................65

Methods of Receiving Errors and Messages ..............66

Descriptions and Corrective Actions for Errors and Messages.......67

Using Sense Data.......................71

Obtaining a Drive Dump ....................75

Viewing the Drive Error Log ...................76

Resolving Problems Reported by the Server ..............77

Fixing SCSI Bus Errors .....................77

Fixing Fibre Channel Errors ...................79

Resolving Media-Related Problems .................82

Chapter 7. Servicing the Tape Drive ................83

Removing a SCSI Tape Drive from an Enclosure ............83

Removing a Fibre Channel Tape Drive from an Enclosure .........84

Manually Removing a Tape Cartridge.................85

Removing the Cartridge ....................85

Fixing an Internal Jam .....................88

Appendix A. Tools and Supplies..................95

iv IBM TotalStorage LTO Ultrium 2 Tape Drive

Appendix B. TapeAlert Flags ...................97

TapeAlert Flags Supported by the Drive................97

Notices ...........................101

Trademarks..........................101

Electronic Emission Notices....................102

Special Considerations for Electromagnetic Compatibility ........102

IBM TotalStorage LTO Ultrium 2 Tape Drive Models T400 and T400F . . . 102

Getting Help .........................104

Warranty...........................104

Glossary ..........................105

Index ............................117

Contents v

vi IBM TotalStorage LTO Ultrium 2 Tape Drive

Safety and Environmental Notices

When using this product, observe the danger, caution, and attention notices that are

contained in this guide. Symbols that represent the severity of the safety condition

accompany the notices.

The sections that follow define each type of safety notice and give examples.

Danger Notice

A danger notice calls attention to a situation that is potentially lethal or extremely

hazardous to people. A lightning bolt symbol always accompanies a danger notice

to represent a dangerous electrical condition. A sample danger notice follows:

DANGER

An electrical outlet that is not correctly wired could place

hazardous voltage on metal parts of the system or the products

that attach to the system. It is the customer’s responsibility to

ensure that the outlet is correctly wired and grounded to prevent

an electrical shock.

Caution Notice

A caution notice calls attention to a situation that is potentially hazardous to people

because of some existing condition. One of several symbols can accompany a

caution notice:

If the symbol is... It means....

A hazardous electrical condition with less severity than an

electrical danger.

A generally hazardous condition not represented by other

safety symbols.

A hazardous condition due to the use of a laser in the

product. Laser symbols are always accompanied by the

classification of the laser as defined by the U. S.

Department of Health and Human Services (for example,

Class I, Class II, and so forth).

Sample caution notices follow:

CAUTION:

The controller card contains a lithium battery. To avoid possible

explosion, do not burn, exchange, or charge the battery. Discard the

controller card as instructed by local regulations for lithium

batteries.

CAUTION:

Do not attempt to use the handle on the module to lift the entire

device (module and enclosure) as a unit. First remove the module;

then, use two hands to lift the enclosure.

Attention Notice

An attention notice indicates the possibility of damage to a program, device, or

system (server), or to data. An exclamation point symbol may accompany an

attention notice, but is not required. Sample attention notices follow:

Attention: If you use a power screwdriver to perform this

procedure it could destroy the tape.

Attention: Do not operate the Ultrium 2 Tape Drive in a poor air quality

environment.

Laser Safety and Compliance

These products contain components that comply with performance standards that

are set by the U.S. Food and Drug Administration (Part 21CFR, 1040.10/11). This

means that these products belong to a class of laser products that do not emit

hazardous laser radiation. This classification was accomplished by providing the

necessary protective housing and scanning safeguards to ensure that laser

radiation is inaccessible during operation or is within Class I limits. External safety

agencies have reviewed these products and have obtained approvals to the latest

standards as they apply to this product type.

viii IBM TotalStorage LTO Ultrium 2 Tape Drive

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere IBM Lagerung Handbücher

IBM

IBM SAN384B-2 Handbuch

IBM

IBM ThinkPad Zip250 Ultrabay 2000 Drive Bedienungsanleitung

IBM

IBM CISCO MDS 9124 - UPDATE FOR SYSTEM STORAGE Technisches Handbuch

IBM

IBM SAN768B Handbuch

IBM

IBM XIV STORAGE SYSTEM Bedienungsanleitung

IBM

IBM TotalStorage DS4800 Betriebsanleitung

IBM

IBM Ultrastar 36LP Installations- und Betriebsanleitung

IBM

IBM System Storage N3220 Handbuch

IBM

IBM 12/24 GB DDS/3 4 mm Bedienungsanleitung

IBM

IBM Ultrastar 9LP Bedienungsanleitung

IBM

IBM LC921 Bedienungsanleitung

IBM

IBM DS4700 EXPRESS Installationsanleitung

IBM

IBM N6270 Bedienungsanleitung

IBM

IBM System x3755Types 7163 Bedienungsanleitung

IBM

IBM 3581 Bedienungsanleitung

IBM

IBM DYLA-28100 - Travelstar 8.1 GB Hard Drive Bedienungsanleitung

IBM

IBM Ultrastar 18XP Bedienungsanleitung

IBM

IBM DS8880 Series Technisches Handbuch

IBM

IBM System Storage DS4000 EXP420 Betriebsanleitung

IBM

IBM 80 GB VS160 Bedienungsanleitung

IBM

IBM 01K1316 Betriebsanleitung

IBM

IBM E Server x 100 Series Bedienungsanleitung

IBM

IBM Elastic Storage System 3200 Bedienungsanleitung

IBM

IBM SAN384B Handbuch

Beliebte Lagerung Handbücher anderer Marken

QNAP

QNAP TS 32PXU Series Bedienungsanleitung

LaCie

LaCie RUGGED RAID Bedienungsanleitung

Freecom

Freecom CLS DOCK Bedienungsanleitung

PNY

PNY Attache P-FD64MBATT3 Bedienungsanleitung

HP StorageWorks MSL2024 Bedienungsanleitung

OLT

OLT 6x6 Maximizer Bedienungsanleitung

Transcend

Transcend JetFlash 160 Bedienungsanleitung

LaCie

LaCie RUGGED MINI Bedienungsanleitung

Thunderbolt

Thunderbolt 600 Bedienungsanleitung

Panasonic

Panasonic LB-DH8 series Handbuch

Intel

Intel RAID High Availability Bedienungsanleitung

LaCie

LaCie 12big Thunderbolt 3 Bedienungsanleitung

Spectra Logic

Spectra Logic T-Series Spectra T50e Bedienungsanleitung

Panasonic

Panasonic LKM-F931-1 Bedienungsanleitung

Tabernus

Tabernus Enterprise Erase E2400 Bedienungsanleitung

Rocstor

Rocstor COMMANDER 3F series Bedienungsanleitung

HP P9000 Bedienungsanleitung

Western Digital

Western Digital Ultrastar Data60 Bedienungsanleitung