IBM CN4093 Bedienungsanleitung

Configuring the IBM Flex System Fabric CN4093 10 b Converged Scalable

Switch

Prerequisites:

Make sure that a IBM Flex System Fabric CN4093 10Gb Con erged Scalable Switch is installed in I/O

module bay 1 or 2 of a Flex System Enterprise chassis and that the chassis is configured. Complete the

following quick start guides:

Installing the IBM Flex System Enterprise Chassis

Initial setup of chassis I/O modules (switches)

Steps:

Note: This process illustrates how to enable the switch ports through the Chassis Management Module

(CMM) command-line interface. For information about using the CMM interface, you can use the

Configuring IBM Flex System nterprise Chassis components quick start guide. You can find that quick

start guide at this location:

In the information center (Internet):

http://pic.dhe.ibm.com/infocenter/flexsys/information/topic/com.ibm.acc.commontasks.doc/commonta

sks_chassis_config.html

The IBM Flex System product documentation is also a ailable on the IBM Flex System Manager management node. To access

the installed documentation, click Information Center from the IBM Flex System Manager Home page and then na igate to:

IBM Flex System information -> Quick start guides -> Installing and configuring the IBM Flex System Enterprise Chassis

1. Log on to the Chassis Management Module (CMM) CLI with an SSH application. The default IP

address is 192.168.70.100 and the default login/password is USERID/PASSW0RD. If necessary, obtain

the IP address and login of the CMM from your system administrator.

2. Set the en ironment to the bay where you installed the switch. For example, if you installed the

switch in I/O module bay 2, enter the following command:

en -T system:switch[2]

3. Run the following command to enable external data ports:

ifconfig -ep enabled

External ports 1-2 and 11-16 are now enabled for data throughput.

Page 1 of 2

Activating additional keys:

If you ha e purchased additional keys, they need to be installed on the switch. Complete the following

steps to install keys using the ISCLI interface:

1. To retrie e the key, na igate a browser to https://www.ibm.com/systems/x/fod/index.wss and sign in

with your ID and Password.

2. Click Request activation key.

3. Enter the authorization code. The authorization code was supplied to you by email or on paper as

part of the ordering process.

4. Click Continue and follow the instructions and download the key file.

5. Log on to the CN4093 switch with an SSH application. The default IP addresses for the switch

through the CMM are as follows: 192.168.70.120 (bay 1), 192.168.70.121 (bay 2), 192.168.70.122

(bay 3), 192.168.70.123 (bay 4). If necessary, obtain the IP address and log in of the switch from

your system administrator.

6. Enter ena.

7. Enter software-key.

8. Enter enakey address <hostname or IP address> keyfile <file name>

protocol tftp mgt-port

Note: you must reset the switch to apply the key.

9. Reset the switch. Enter reload..

Repeat these steps for additional keys, if needed. The sequence of steps is shown here:

Router#ena

Router(config)#software-key

Router(Software-Key)#enakey address 9.44.143.206 keyfile

ibm_fod_0007_ 010CM28N001_anyos_noarch.key protocol tftp mgt-port

Starting download key file...

Key file download complete (494 bytes)

Software feature Upgrade1 will be Active upon next reboot.

Aug 5 11:47:39 1080:0:0:0:0:0:0:82 NOTICE mgmt: Software feature Upgrade1

will be Active upon next reboot.

A Reboot is required for the new settings to take effect.

Router(Software-Key)#reload

...

Resetting at 11:47:59 Tue Aug 5, 2014...

Page 2 of 2

Andere Handbücher für CN4093

Inhaltsverzeichnis

Andere IBM Schalten Handbücher

IBM

IBM 2109 - SAN Fibre Channel Switch Model S16 Bedienungsanleitung

IBM

IBM 8237 Bedienungsanleitung

IBM

IBM Flex System FC3171 Bedienungsanleitung

IBM

IBM 8265 Nways ATM Switch Bedienungsanleitung

IBM

IBM RackSwitch G8000 Bedienungsanleitung

IBM

IBM FC5022 Bedienungsanleitung

IBM

IBM SAN40B-4 - System Storage Switch Fehlerbehebungshandbuch

IBM

IBM T860 Bedienungsanleitung

IBM

IBM 8285 Nways Bedienungsanleitung

IBM

IBM Flex System Fabric EN4093 Bedienungsanleitung

IBM

IBM 8271 F12 Bedienungsanleitung

IBM

IBM RackSwitch G8264CS Bedienungsanleitung

IBM

IBM BNT Bedienungsanleitung

IBM

IBM RS/6000 SP Bedienungsanleitung

IBM

IBM 8239 Token-Ring Stackable Hub Sicherheitsleitfaden

IBM

IBM ThinkPad 600 Bedienungs- und Sicherheitshinweise

IBM

IBM 3110X - Cisco Catalyst Switch Handbuch

IBM

IBM 524 Bedienungsanleitung

IBM

IBM 8271 Nways Ethernet LAN Switch Bedienungsanleitung

IBM

IBM RedBooks SAN24B-5 Bedienungsanleitung

IBM

IBM TotalStorage 3534-F08 Bedienungsanleitung

IBM

IBM SAN32M-2 Bedienungsanleitung

IBM

IBM TotalStorage 2109 M12 Montage- und Wartungsanleitung

IBM

IBM Global console manager Bedienungsanleitung

Beliebte Schalten Handbücher anderer Marken

URC

URC Total Control MFS-8 Bedienungsanleitung

Azbil

Azbil HPQ-D11 Bedienungsanleitung

Sony

Sony DFS-900M Bedienungsanleitung

SICK

SICK i17S Bedienungsanleitung

F&F

F&F SZR-277 Bedienungsanleitung

Shure

Shure UAMS/BK Bedienungsanleitung

Dräger

Dräger X-zone Switch Off Bedienungsanleitung

Asco

Asco Joucomatic 349 Series Bedienungsanleitung

BT Mini Hub Bedienungsanleitung

D-Link

D-Link DES-1226G Bedienungsanleitung

Johnson Controls

Johnson Controls FS80-C Bedienungsanleitung

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Bedienungsanleitung

MicroNet

MicroNet SP1200A Bedienungsanleitung

Ruijie

Ruijie RG-PF2920 Series Installations- und Betriebsanleitung

Altinex

Altinex DA1914SX Bedienungsanleitung

MiLAN

MiLAN MIL-SM2401M Bedienungsanleitung

RJM

RJM MASTERMIND PBC/6X Bedienungsanleitung

Atlas

Atlas MMK-KVM8 Bedienungsanleitung